Satel INT-SF Bedienungsanleitung

Andere Handbücher für INT-SF

2

Inhaltsverzeichnis

Andere Satel Tastenfeld Handbücher

Satel

Satel PRF-LCD Bedienungsanleitung

Satel

Satel VERSA INT-TSH2 Betriebsanleitung

Satel

Satel INT-TSG2 Betriebsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Satel

Satel VERSA-LCDM-WRL Bedienungsanleitung

Satel

Satel Integra INT-KSG2R Bedienungsanleitung

Satel

Satel VERSA INT-TSH2 Benutzerhandbuch

Satel

Satel INT-KWRL Bedienungsanleitung

Satel

Satel INT-SF Bedienungsanleitung

Satel

Satel INTEGRA INT-TSH2 Bedienungsanleitung

Satel

Satel INT-KSG Benutzerhandbuch

Satel

Satel INT-TSG2 Bedienungsanleitung

Satel

Satel INT-TSI Bedienungsanleitung

Satel

Satel CR-MF5 Bedienungsanleitung

Satel

Satel INT-SK-GR Bedienungsanleitung

Satel

Satel INT-SCR Bedienungsanleitung

Satel

Satel INT-TSH Bedienungsanleitung

Satel

Satel INT-SF Bedienungsanleitung

Satel

Satel INT-TSG Bedienungsanleitung

Satel

Satel INT-S Bedienungsanleitung

Satel

Satel MKP-300 Bedienungsanleitung

Satel

Satel INT-S Series Bedienungsanleitung

Satel

Satel PRF-LCD-WRL Bedienungsanleitung

Satel

Satel CA-6 KLED Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung

INT-SF

Partition keypad int-sf_sii_en 07/20

Quick installation guide

Full manual is available on www.satel.eu

The device should be installed by qualified personnel.

Before installation, please read the full manual thoroughly.

Disconnect power before making any electrical connections.

The keypad is designed for indoor installation. The place of installation should be readily

accessible to the system users.

1. Open the keypad enclosure (Fig. 1). The enclosure opening tool, shown in the illustration,

is included in the keypad delivery set.

2. Set the partition keypad address (see “Address setting”).

3. Run the wires through the opening in the enclosure base.

4. Using wall plugs (anchors) and screws, fasten the enclosure base to the wall. Select wall

plugs specifically intended for the mounting surface (different for concrete or brick wall,

different for drywall, etc.).

5. Connect the CLK, DTA and COM terminals to the appropriate terminals of the control

panel expander bus (see the control panel installer manual).

2 INT-SF SATEL

6. If the partition keypad is to control an electric strike, electromagnetic lock or another door

actuator, connect this device to the NO terminals as shown in Fig. 2. It is not

recommended that the door actuator be powered from the same source as the partition

keypad.

7. If the keypad is to supervise the door status, connect the detector supervising the door

status to the IN and COM terminals. If the keypad is not to supervise the door status,

connect the IN terminal to the COM terminal or, when configuring the keypad, set value 0

for the “Max. door open time” parameter.

8. Connect the power wires to the 12V and COM terminals. The keypad may be powered

directly from the control panel, from an expander with power supply or from a power

supply.

9. Close the enclosure and then lock it with the screw.

10.Power on the alarm system.

11.Start the identification function in the control panel (see the control panel installer

manual). The keypad will be identified as "INT-S/SK".

Address setting

To set the address, use the DIP switches on the electronics board. The switches have

numbers assigned to them. The number for OFF position is 0. The numbers assigned to the

switches in ON position are presented in the table below. The sum of these numbers is the

address set.

Switch (ON position)

1 2 3 4 5

Number

1

2

4

8

16

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu