Satel SILVER Bedienungsanleitung
®
SILVER
DIGITAL DUAL TECHNOLOGY MOTION DETECTOR
silver_en 12/11
1. Features
•Combined PIR and microwave technology.
•Digital motion detection algorithm.
•Digital temperature compensation.
•Selectable operation modes: basic or advanced.
•Microwave based anti-mask feature
•Remote LED enable/disable.
•Alarm memory.
•Supervision of detector signal path and supply voltage.
•Capability of separate sensor testing.
•Tamper protection against enclosure opening.
2. Specifications
Supply voltage........................................................................................................... 12 V DC ±15%
Standby current consumption..................................................................................................18 mA
Maximum current consumption ...............................................................................................25 mA
Relay contacts rating (resistive load) ..................................................................... 40 mA / 16 V DC
Microwave frequency...................................................................................................... 10.525 GHz
Detectable speed.............................................................................................................. 0.3...3 m/s
Alarm signaling time ......................................................................................................................2 s
Security grade according to EN50131-2-4 ........................................................................... Grade 2
Standards complied with .................................EN50131-1, EN50131-2-4, EN50130-4, EN50130-5
Environmental class according to EN50130-5 ................................................................................ II
Operating temperature range .........................................................................................-30...+55 °C
Maximum humidity.................................................................................................................. 93±3%
Dimensions............................................................................................................62 x 136 x 49 mm
Recommended installation height ............................................................................................ 2.4 m
Weight ...................................................................................................................................... 126 g
The declaration of conformity may be consulted at www.satel.eu/ce
3. Operation modes
Basic – the detector indicates an alarm if both sensors detect motion within a time period shorter
than 3 seconds.
Advanced – the detector indicates an alarm if:
−both sensors detect motion within a time period shorter than 3 seconds;
−within a time interval less than 3 seconds, the microwave sensor detects motion and the
PIR sensor detects some changes in coverage area, insufficient however to be recognized
as motion;
−within 15 minutes' period, the microwave sensor detects motion 16 times, but PIR sensor
does not detect any changes in coverage area.
2 SILVER SATEL
4. Anti-mask feature
Detection by the microwave sensor of an object moving at a distance of 10-20 centimeters from
the detector is interpreted as an attempt to mask the detector and results in opening the anti-
masking relay contacts for two seconds. Objects permeable to microwaves, but isolating the
infrared radiation are not detected by the anti-masking feature.
5. Supervision features
In the event of the signal path failure or the voltage drop below 9 V (± 5%) for more than
2 seconds, the detector will signal a trouble. The trouble is indicated by the activation of alarm
relay and the steady red light of LED indicator. The trouble signaling will continue as long as the
trouble persists.
6. Electronics board
terminals:
WRN - anti-masking relay (NC).
TMP - tamper contact (NC).
COM - common ground.
12V - power supply input.
NC - alarm relay (NC).
LED - remote LED control (the LED pins
must be open). The LED is enabled
when the input is short-circuited to
common ground. To control the input,
you can use the OC type output of the
control panel, programmed e.g. as
SERVICE MODE INDICATOR or BI SWITCH.
MEM - alarm memory control. When the input
is short-circuited to common ground
and the detector signals alarm, the
LED will indicate the alarm memory.
Disconnecting the input from common
ground will not clear the alarm
memory. Signaling the alarm memory
will continue until the input is shorted
to common ground again. To control
the input, you can use the OC type
output of the control panel,
programmed e.g. as ARM STATUS.
microwave sensor.
two-color LED to indicate:
– alarm – LED lit up red for 2 seconds;
– motion detection by one of the sensors – LED lit up green for 2 seconds;
– warm-up – LED flashing alternately red and green;
– trouble – LED lit up red.
potentiometer for sensitivity adjustment of the microwave sensor. Please bear in mind that
microwaves can penetrate e.g. glass, gypsum walls, non-metallic doors, etc.
potentiometer for sensitivity adjustment of the PIR sensor.
MODE pins – selecting the detector operation mode:
– pins shorted – basic mode;
– pins open – advanced mode.
SATEL SILVER 3
LED pins – enable/disable LED indicator. The LED indicator is enabled when the pins are
shorted (remote LED control is not possible then).
dual pyroelectric sensor.
tamper contact.
fixing screw hole.
7. Installation
Do not touch the pyroelectric sensor, so as not to soil it.
1. Open the enclosure (Fig. 2).
2. Remove the electronics board.
3. Make the openings for screws and cable in the enclosure base.
4. Pass the cable through the prepared opening.
5. Fix the enclosure base to the wall or to the attached bracket (Fig. 3 and 4).
6. Fasten the electronics board.
7. Connect the wires to the corresponding terminals.
4 SILVER SATEL
8. Using potentiometers and jumpers, set the working parameters of the detector.
9. Close the detector enclosure.
8. Start-up and walk test
1. Turn the power on. The detector warm-up lasts 30 seconds. During that time, the detector
stabilizes and the LED indicator (if enabled) is alternately flashing red and green.
2. After completion of the warm-up, check that motion within the coverage area (Fig. 5) will
activate the alarm relay and the LED indicator will light up red.
9. Separate testing of sensors
To test the microwave sensor, do the following:
1. Before you turn the power on, put the jumper on the MODE pins.
2. Turn the power on and, during the warm-up, remove the jumper from the MODE pins. After
completion of the warm-up, the LED should flash green every 3 seconds.
3. Check that movement within the coverage area will activate the alarm relay and the LED
indicator will light up green.
To test the PIR sensor, do the following:
1. Before you turn the power on, remove the jumper from the MODE pins.
2. Turn the power on and, during the warm-up, put the jumper on the MODE pins. After
completion of the warm-up, the LED should flash red every 3 seconds.
3. Check that movement within the coverage area will activate the alarm relay and the LED
indicator will light up red.
Note: The sensor separate testing mode is automatically exited after 20 minutes.
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
www.satel.pl
Andere Handbücher für SILVER
3
Inhaltsverzeichnis
Andere Satel Sicherheitssystem Handbücher
Satel
Satel CA-64 E Bedienungsanleitung
Satel
Satel Versa Bedienungsanleitung
Satel
Satel SPL-5010 Bedienungsanleitung
Satel
Satel SPL-2030-R Bedienungsanleitung
Satel
Satel CA-4M Bedienungs- und Wartungsanleitung
Satel
Satel ASP-201 Bedienungsanleitung
Satel
Satel SPL-2030 Bedienungsanleitung
Satel
Satel MICRA Bedienungsanleitung
Satel
Satel SP-500 Bedienungsanleitung
Satel
Satel SP-4001 Bedienungsanleitung
Satel
Satel CA-64 E Bedienungsanleitung
Satel
Satel SPL-2010 Bedienungsanleitung
Satel
Satel ECAM22 Bedienungsanleitung
Satel
Satel APD-200 Bedienungsanleitung
Satel
Satel SPW-100 Bedienungsanleitung
Satel
Satel SP-4003 R Bedienungsanleitung
Satel
Satel CSP-204 Installationshandbuch
Satel
Satel SD-3001 Bedienungsanleitung
Satel
Satel ASP-105 Technisches Handbuch
Satel
Satel ASP-205 Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung