Satel SPL-2030-R Bedienungsanleitung

OPTICAL-ACOUSTIC

SIGNALING DEVICE

SPL-2030

spl2030_en 09/08

The SPL-2030 op ical-acous ic signaling device (siren) is designed for applica ion in he

burglary and assaul signaling sys ems. The signaling func ion is performed in wo ways:

visually (by blinking of indica or LEDs si ua ed in he lower par of he enclosure) and

acous ically (by a modula ed high-volume sound signal). As he ligh source, a se of LEDs is

used, whereas he sound signal is genera ed by means of a piezoelec ric ransducer. Design

of he signaling device housing ensures a high degree of amper pro ec ion (agains opening

and/or earing off from he base). The elec ronic circui is made by he use of SMD echnique

and impregna ed agains he adverse influence of wea her condi ions, which ensures a high

reliabili y of he device. As he SPL-2030 ex ernal housing is made of he PC LEXAN

high-impac polycarbona e, i is charac erized by a very high mechanical s reng h, and a nice

appearance of he device is guaran eed even af er many years of service.

1. Outfit options

The siren can be fi ed wi h addi ional elemen s of amper pro ec ion (sold separa ely),

including:

• inner cover of galvanized me al shee , OM-SPL2000,

• foam de ec or, SPL-SAB or SPL-TO.

In order o ins all he SPL-SAB de ec or, remove he elec ronics board and unsolder he SMD

componen (si ua ed undernea h he board), designed for shor ing he solder poin s J3

and J4. Nex , solder he de ec or leads o hese poin s and, using a screw, a ach

he de ec or o he siren base (so as o cover he opening) and remoun he PCB.

2. Installing

The SPL-2030 siren should be moun ed on fla ver ical surface in inaccessible place in order

o minimize ampering possibili y. I mus be a ached o he surface by means of screws and

expansion plugs ( he screws and expansion plugs are included in he device delivery se ).

Note: Make sure to leave a distance of about 4.5 cm between the upper edge of the

signaling device base and the ceiling or another object which limits the mounting

position from above. With no gap, mounting of the signaling device external housing

may be difficult.

Explana ions for Figure 1:

1 – moun ing holes

2 – auxiliary opening

3 – foam de ec or (op ion)

4 – buzzer

5 – cable hole

6 – amper elemen “S” (should be screwed o he moun ing surface; do no apply excessive

force, so as no o break he narrowings)

7 – wa er drain holes (make sure hey are no s opped)

2 SATEL SPL-2030

Fig. 1. View of he SPL-2030 siren enclosure

Af er moun ing he siren i is recommended o seal he moun ing holes, auxiliary opening, and

cable en ry hole wi h silicon rubber pas e.

3. Connections

The SPL-2030 signaling device can be used wi h any equipmen which sends 12V DC on

ou pu o ac iva e signaling. Connec ing +12 V power supply o he "+ SA –" erminals will

rigger he acous ic signaling, and o he "+ SO –" erminals - he op ical signaling in

he SPL-2030 device.

The amper circui of he siren will be open on removing he ou er enclosure, covering wi h

moun ing foam, or de aching he siren from he wall. For he amper con ac o func ion

correc ly during pull-off, he "S" elemen mus be screwed o he moun ing surface

(see Fig. 1).

Connec ors "TMP" are designed for connec ing in o amper circui of securi y sys em.

By placing jumpers on he P1– P5 pins, you can selec one of he hree audible signals for

alarm signaling.

JP2

JP1

JP4

JP3

JP5

MEL1=JP1+JP4

JP2

JP1

JP4

JP3

JP5

MEL3=JP3+JP5

JP2

JP1

JP4

JP3

JP5

MEL2=JP2+JP5

Fig. 2. The manner of placing jumpers o ob ain he required signaling one.

– pins shor ed

– pins open

SPL-2030 SATEL 3

INTEGRA 32

SPL-2030

SO TMPSA

OUT1 COMCOM COM Z1

OUT2

COM OUT1 COM COM COM COMOUT2 +KPD DTM CKM +EX CK AUX Z1

Fig. 3. Connec ing he SPL-2030 siren o high-curren ou pu s of INTEGRA 32

con rol panel. The OUT1 ou pu will release op ical signaling, and he OUT2

ou pu - acous ic (high-curren ou pu s wi h normal polariza ion - ac iva ed when +12 V

vol age is supplied). The Z1 zone is programmed as 24 h amper.

I is possible o con rol wo ypes of signaling from one ou pu of con rol panel, by connec ing

in parallel he erminals +SA o +SO and -SA o -SO.

Note: ome control panels may require connecting a resistor R (approx. 1 kΩ) between

the +SA- terminals in the siren. If this resistor is not connected, the siren may emit

some low sounds when not alarming.

Descrip ion of he erminals:

+SO- – op ical signaling erminals

+SA- – acous ic signaling erminals

TMP – amper circui erminals

4 SATEL SPL-2030

SPL-2030

INTEGRA 32

AUX Z1 COMCOM CK

COM Z2

CKM +EX DT+KPD DTM

OUT2

OUT3

OUT4

OUT5

OUT6

OUT7

OUT8

SO TMPSA

Fig. 4. Connec ing he SPL-2030 siren o low-curren ou pu s of INTEGRA 32 con rol

panel. The OUT2 ou pu has been programmed as power ou pu . The OUT3 ou pu

con rols he P1 relay, which releases acous ic signaling, and he OUT4 ou pu con rols

he P2 relay, which releases op ical signaling (low-curren ou pu s wi h normal

polariza ion - ac iva ed by shor ing he erminal direc ly o he common ground 0 V).

The Z2 zone is programmed as 24 h amper.

4. Technical data

Nominal power supply ........................................................................................ 12 V DC ±20%

Mean curren consump ion when signaling

acous ic signaling ...................................................................................... 250 mA

op ical signaling ..........................................................................................35 mA

Working empera ure range ................................................................................... -35…+60 °C

Sound pressure .................................................................................................. approx. 120 dB

Enclosure dimensions ...................................................................................... 298x197x90mm

Weigh ............................................................................................................................... 725 g

SATEL sp. z o.o.

ul. Schuber a 79

80-172 Gdańsk

POLAND

el. (+48 58) 320 94 00

info@sa el.pl

www.sa el.pl

La es EC declara ion of conformi y and

produc approval cer ifica es can be

downloaded from our web si e www.satel.pl

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel ABAX 2 ASP-200 Bedienungsanleitung

Satel

Satel WZ-100 Bedienungsanleitung

Satel

Satel Integra 24 Benutzerhandbuch

Satel

Satel SPL-2030 Bedienungsanleitung

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel INT-TSG Betriebsanleitung

Satel

Satel ASP-215 Bedienungsanleitung

Satel

Satel ASP-100-R Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SP-500 Bedienungsanleitung

Satel

Satel SD-3001 R Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel SPW-100 Bedienungsanleitung

Satel

Satel ASP-205 Bedienungsanleitung

Satel

Satel SOW-300 Series Bedienungsanleitung

Satel

Satel CSP-204 Installationshandbuch

Satel

Satel SP-6500 Bedienungsanleitung

Satel

Satel Versa Bedienungsanleitung

Satel

Satel ASP-105 Technisches Handbuch

Satel

Satel SP-4002 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung