Satel SD-3001 Bedienungsanleitung

OPTICAL-ACOUSTIC

OUTDOOR SIREN

SD-3001

sd3001_en 10/12

The SD-3001 optical-acoustic outdoor siren comes in three versions differing by the color of optical

signaling (red in SD-3001 R, blue in SD-3001 BL and orange in SP-3001 O).

1. Features

•Acoustic signaling by means of dynamic horn.

•Optical signaling by means of LEDs.

•Optional operation with a backup battery.

•Four selectable tones for acoustic signaling.

•Weatherproofed electronic circuit.

•Tamper protection in 2 ways – cover opening or tearing housing from the wall.

•Inner cover of galvanized metal sheet.

•Housing made of PC LEXAN high-impact polycarbonate, featuring a very high mechanical

strength.

Explanations for Fig. 1:

1 - cover mounting openings.

2 - holes for screws fixing the base to mounting

surface.

3 - dynamic horn.

4 - tamper contact (NC). The mechanical tamper

contact can be optionally replaced with

a hermetically sealed reed switch, which can

be purchased separately.

5 - cable inlet.

6 - hole for a screw fixing the tamper element to

the mounting surface. Be careful when

screwing down the tamper element so as not

to damage the narrowings that connect it with

the housing base (these narrowings will be

broken at an attempt to tear off the siren from

the mounting surface).

7 - electronics board.

8 - water drain opening (do not seal it).

Fig. 1. View of the siren housing base.

2. Functioning

The siren requires 12 V DC ±15% power supply. The signaling is generated by changing the STA

input status (acoustic signaling) or the STO input status (optical signaling). The way of triggering the

alarm is set by means of the PLA and PLO pins. The alarm can only be triggered 20 seconds after

power-up, provided that during that time the signaling control input status was stable and consistent

with that set by means of pins for inactive status. The 20-second delay prevents the alarm from being

accidentally triggered during installation work.

The maximum duration of acoustic signaling is set by means of the TM0 and TM1 pins (the fact that

the acoustic signaling control output of the control panel will be active longer is of no significance).

2 SD-3001 SATEL

Triggering the acoustic signaling again will only be possible after the control signal is restored to its

status which preceded the alarm.

If the control wires are cut or the external power supply is lost (provided that a battery is installed), the

tamper signaling is triggered (signaling mode: pins O+A; signaling duration: pins TM0 and TM1).

The siren is designed for operation with a 12 V 1,2 Ah lead-acid battery, but it can also work without

one.

Notes:

•The battery charging system used in the siren is designed for recharging a partially discharged

battery, not for charging a fully discharged one.

•The current consumed by the siren to charge the battery depends on the battery degree of

discharge.

3. Description of electronics board

Fig. 2. View of the electronics board.

Explanations for Fig. 2:

1 - battery leads (red +, black -).

2 - tamper contact wires.

3 - terminals:

STO - optical signaling control.

STA - acoustic signaling control.

TMP - tamper circuit.

+12V - power supply.

COM - common ground.

4 - battery charging system fuse (3.15 A).

5 - siren configuration pins (see section CONFIGURING SIREN).

6 - pins for switching ON/OFF the external power supply indication. The indication is enabled when

the pins are shorted.

7 - LED indicating external power supply (a short flash approximately every 3 seconds).

8 - LEDs for visual indication of the alarm.

SATEL SD-3001 3

4. Configuring siren

- pins shorted; - pins open

Type of acoustic signaling

Two sound frequencies (1550 Hz/2600 Hz) alternating during 1

second

Sound with a smoothly rising and falling frequency (1550 Hz –

2600 Hz – 1550 Hz) during 1 second

Sound with a rising frequency (od 1550 Hz do 2600 Hz) during 1

second

Sound with a falling frequency (od 2600 Hz do 1550 Hz) during 1

second

Maximum duration of acoustic signaling / duration of tamper signaling

Approx. 1 minute

Approx. 5 minutes

Approx. 10 minutes

Approx. 15 minutes

Tamper signaling mode

Optical and acoustic signaling

Acoustic signaling only

Way of triggering acoustic alarm (polarization of STA input)

On common ground cut-off (inactive status: common ground present on STA input)

On +12 V voltage loss (inactive status: +12 V present on STA input)

Way of triggering optical alarm (polarization of STO input)

On common ground cut-off (inactive status: common ground present on STO input)

On +12 V voltage loss (inactive status: +12 V present on STO input)

5. Installation

Install the siren on flat surface, in a hard-to-reach place, so as to minimize the risk of tampering. The

device must be attached to the surface by means of screws and expansion plugs.

Note: Leave a distance of at least 0.5 cm between the upper edge of the siren housing and the

ceiling or another object located above the siren. Otherwise, replacement of the cover may be

impossible.

On completion of the installation, it is advisable to seal the mounting holes and the cable inlet with

silicone compound.

6. Connection

All connections should only be made after the alarm system power supply has been

turn off and with disconnected battery.

4 SD-3001 SATEL

Fig. 3. Way of connecting the SD-3001 siren to the alarm control panel. The OUT1 high-current output

is programmed as supply. The OUT7 & OUT8 low-current outputs control the signaling (OUT7

triggers acoustic signaling, OUT8 – optical). The Z3 zone is programmed as tamper, NC type. The R

resistor value is 2.2 kΩ.

7. Specifications

Power supply....................................................................................................................12 V DC ±15%

Standby current consumption (without battery).............................................................................35 mA

Maximum current consumption (without battery):

optical signaling......................................................................................................35 mA

acoustic signaling.....................................................................................................1.7 A

optical and acoustic signaling...................................................................................1.7 A

Sound pressure level (at 1 m distance)...............................................................................up to 120 dB

Environmental class according to EN50130-5.......................................................................................III

Operating temperature range...............................................................................................-35...+55 °C

Maximum humidity........................................................................................................................ 93±3%

Housing dimensions..................................................................................................195 x 300 x 97 mm

Weight ..........................................................................................................................................1.21 kg

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.eu

The latest EC declaration of conformity and product approval certificates are available

for downloading on website www.satel.eu

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel SP-4002 Bedienungsanleitung

Satel

Satel SD-3001 R Bedienungsanleitung

Satel

Satel SOW-300 Series Bedienungsanleitung

Satel

Satel ECAM22 Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel MSP-300 Bedienungsanleitung

Satel

Satel Integra 24 Benutzerhandbuch

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel SPW-150 Bedienungsanleitung

Satel

Satel SP-4001 Bedienungsanleitung

Satel

Satel ASP-201 Bedienungsanleitung

Satel

Satel SPL-2030-R Bedienungsanleitung

Satel

Satel ROP-101/EU Bedienungsanleitung

Satel

Satel ASP-205 Bedienungsanleitung

Satel

Satel ASP-200 Bedienungsanleitung

Satel

Satel SP-500 Bedienungsanleitung

Satel

Satel CA-4M Bedienungs- und Wartungsanleitung

Satel

Satel Micra MPB-300 Bedienungsanleitung

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel SPW-250 Bedienungsanleitung

Satel

Satel Versa Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel SP-6500 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung