Satel SPL-2030 Bedienungsanleitung

SPL-2030

OPTICAL-ACOUSTIC OUTDOOR SIREN

spl2030_en 07/16

The SPL-2030 siren provides information about alarm situations by means of optical and

acoustic signaling.

1. Features

Acoustic signaling by means of piezoelectric transducer.

Three selectable tones for acoustic signaling.

Optical signaling by means of LEDs.

Weatherproofed electronic circuit.

Tamper protection in 2 ways – cover removal and tearing enclosure from the wall.

High-impact polycarbonate enclosure, featuring a very high mechanical strength.

2. Description

Explanations for Fig. 1:

mounting holes.

auxiliary hole.

mounting holes for additional SPL-TO tamper sensor.

piezoelectric transducer.

opening for wires.

2 SPL-2030 SATEL

electronic board.

tamper element with mounting hole.

water drain holes (do not plug).

Terminals

+SO- - input to trigger the optical signal. The signaling will be triggered after +12 V DC

voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to

terminal “-“.

+SA- - input to trigger the acoustic signal. The signaling will be triggered after +12 V DC

voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to

terminal “-“.

TMP - tamper output (NC). Connect one terminal to the control panel zone programmed

as tamper, and the other to the control panel common ground.

Pins for selecting acoustic signal

Fig. 2 shows how the jumpers should be placed to select the tone which will be used by the

siren: A – tone 1; B – tone 2; C – tone 3.

Additional tamper protection

Optionally, the SPL-TO optical tamper sensor can be installed in the siren. It will detect any

attempt to tamper with the siren using mounting foam. The sensor can be used to create an

independent tamper circuit or connected in series with the tamper circuit of the siren.

3. Installation and start-up

Power down the control panel before connecting the siren to it.

The siren must be installed on the wall, high above the floor, at a hard to access location, so

as to minimize the risk of tampering. Make sure that some free space is left above the siren

(at least 4.5 cm). Otherwise, it will be impossible to replace the cover.

1. Remove the cover locking screw.

2. Lift up the enclosure cover by approx. 60º and remove it.

3. Place the enclosure base on the wall and mark the location of mounting holes. Remember

to allow for the mounting hole in the tamper element (see Fig. 1).

4. Drill the holes for wall plugs (screw anchors).

5. Run the wires through the opening in the enclosure base (see Fig. 1).

6. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the wall (the

wall plugs and screws are included in the siren delivery set). Be careful when screwing

down the tamper element so as not to break the narrowings.

SATEL SPL-2030 3

7. Connect the siren terminals with wires to the control panel terminals.

Note: Some alarm control panels may require that a resistor R (approx. 1 kΩ) be connected

between the +SA- terminals in the siren (see Fig. 3). Otherwise, the siren will produce

a buzzing sound when inactive.

8. Use jumpers to select the tone which will be used by the siren (see: Fig. 2).

9. Replace the siren cover, close the cover and then lock it with the screw.

10.Power on the control panel.

11.Test the siren for correct functioning. In order to test the siren you can use the output test

function, which is available in some control panels, or you can trigger an alarm for testing

purposes.

4. Specifications

Supply voltage ................................................................................................... 12 V DC ±15%

Maximum current consumption:

optical signaling ..........................................................................................30 mA

acoustic signaling .....................................................................................180 mA

Sound pressure level (at 1 m distance) .................................................................up to 120 dB

Environmental class according to EN50130-5 ........................................................................ III

Operating temperature range..................................................................................-35...+55 °C

Maximum humidity.......................................................................................................... 93±3%

Dimensions ..................................................................................................298 x 197 x 90 mm

Weight............................................................................................................................... 725 g

The declaration of conformity may be consulted at www.satel.eu/ce

4 SPL-2030 SATEL

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu

Inhaltsverzeichnis

Andere Satel Sicherheitssystem Handbücher

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel ASP-100 Bedienungsanleitung

Satel

Satel Micra MSP-300 Bedienungsanleitung

Satel

Satel SP-6500 Bedienungsanleitung

Satel

Satel SD-3001 Bedienungsanleitung

Satel

Satel ASP-105 Technisches Handbuch

Satel

Satel ABAX 2 Bedienungsanleitung

Satel

Satel ASP-105 Bedienungsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel SP-4003 R Bedienungsanleitung

Satel

Satel INT-TSG Betriebsanleitung

Satel

Satel SILVER Bedienungsanleitung

Satel

Satel SPL-2010 Bedienungsanleitung

Satel

Satel ASP-200 Bedienungsanleitung

Satel

Satel ROP-101/EU Bedienungsanleitung

Satel

Satel CA-4M Bedienungs- und Wartungsanleitung

Satel

Satel SP-4002 Bedienungsanleitung

Satel

Satel SPW-150 Bedienungsanleitung

Satel

Satel ASP-201 Bedienungsanleitung

Satel

Satel SD-3001 R Bedienungsanleitung

Satel

Satel CA-64 E Bedienungsanleitung

Satel

Satel SPLZ-1011 Bedienungsanleitung

Satel

Satel SPL-5010 Bedienungsanleitung

Satel

Satel ABAX 2 ASP-200 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung