Schwinn IC Pro Bedienungsanleitung

PN001-7187 Rev A (12/11/2007)

Nautilus®Bowflex®Schwinn®Fitness Pearl Izumi®StairMaster®Universal®Nautilus Institute®

Assembly Manual

IC Pro™, IC Elite™

Schwinn®IC Bikes

Table of Contents

Product Specifications

Product Speciﬁcations 2

Safety Warnings 3

Exploded Drawing 4

Parts List 5

Assembly Steps 6

Contact Numbers 11

Dimensions 50” L x 22.5” W x 39” H (127cm x 57cm x 99cm)

Assembled Unit Weight 119 lbs (54 kg)

Packaged Shipping weight 123 lbs (56 kg)

Workout Area 89” L x 61.5” W (227cm x 156cm)

Maximum User Weight 300 lbs (136 kg)

Assembly Manual

Safety Warnings

This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Read and understand the complete Owner’s Manual.

Read and understand all Warnings on this machine.

Before using this equipment, obey the following warnings:

• Keep children away from this machine. Watch them closely when near the machine. Moving parts that appear dangerous to adults

may not appear so to children.

• Consult a physician before starting an exercise program. Stop exercising if you feel pain or tightness in your chest, become

short of breath, or feel faint. Contact your doctor before using the machine again.

• The flywheel momentum of the Schwinn®IC Bike will keep the pedals turning even after the rider stops pedaling or the rider’s

feet slip off. DO NOT ATTEMPT TO DISMOUNT THE BIKE OR REMOVE YOUR FEET FROM THE PEDALS UNTIL BOTH THE

PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of control

and serious personal injury.

• Examine this machine for loose parts or signs of wear. Contact Nautilus Customer Service for repair information. Use only

genuine Schwinn®IC replacement parts supplied by Nautilus.

• Do not wear loose clothing or jewelry. This machine contains moving parts.

• Do not place fingers or any other objects into moving parts of the exercise equipment.

• Maximum user weight limit: 300 lb. (136 kg). Do not use if you are over this weight.

• Stabilize the pedals before stepping on them and use caution when stepping off the machine.

• Keep at least 19.7 inches (0.5 m) on each side of the machine clear. This is the recommended safe distance for access and

passage around and emergency dismounts from the machine.

• Warn bystanders to keep a safe distance, at least 3 feet (1 m). Do not allow anyone to touch the operator while the machine is

in motion.

• Keep the foot pedals clean and dry.

• Do not over exert yourself during exercise. Operate the machine in the manner described in this manual.

Assembly Manual

Exploded Drawing

Assembly Manual

Parts List

Ref. # Description Qty.

1 Frame 1

42 Handle Bar 1

3 Seat Slider Assembly with Saddle 1

A Front Stabilizer Bar with Wheels and Feet 1

B Rear Stabilizer Bar with Feet 1

51 Water Bottle Cage 2

Small Parts Box 1

Small Part Box Contents

43 Pedals with Toe Clips & Straps (Left & Right) 1 Pair

29 Pop Pin Assembly for Head Tube 1

46 13mm Hex Bolt 4

44 Flat Washer 8

45 13mm Lock Nut 4

Tools Supplied

Stamped Steel 13/14/15/17mm Combination Wrench 1

3mm Hex Wrench 1

Prior to assembly of the product, remove all components from the packaging and check them against the packaged components

list supplied above. Once you are certain that all the necessary parts have been supplied, begin with the ﬁrst assembly step.

Tools Needed

3mm Hex Wrench

Stamped Steel Combination Wrench

Adjustable wrench (not included)

Grease (not included)

17/15 13/14

Assembly Manual

Assembly

Step 1

Ref. # Description Qty

1 Frame 1

A Front Stabilizer Bar with Wheels and Feet 1

B Rear Stabilizer Bar with Feet 1

46 13mm Hex Bolt 4

44 Flat Washer 8

45 13mm Lock Nut 4

Tools Required

Stamped Steel Combination Wrench 1

Adjustable wrench or 13mm Socket 1

Front

Rear

ATTENTION

The following steps utilize stainless steel hardware. Stainless

steel hardware is susceptible to “cold welding”, also known as

galling, if not handled properly. To reduce the chances for cold

welding, make sure you apply grease to the threads at the end of

the stainless hex bolts #46. When tightening the 13mm lock nuts

#45, turn them at a fairly low rotational speed. High rotational

speeds as well as lack of grease are common causes for cold

welding of stainless steel hardware.

A. Position the Front Stabilizer Bar (A) on the frame bracket as

shown in the illustration.

B. Make sure the adjustable feet are on the bottom and the

transport wheels are facing up and toward the front of the

bike.

C. Attach Front Stabilizer Bar (A) to Frame (1) using two hex

bolts (46), four washers (44), and two lock nuts (45). Tighten

hardware ﬁrmly but do not over tighten as deformation of the

stabilizer tube may occur

D. At this time make sure that the adjustable feet with lock nuts

are screwed fully into the stabilizer.

E. Position the Rear Stabilizer Bar (B) on the frame bracket as

shown in the illustration.

F. Make sure the adjustable feet are on the bottom.

G. Attach Rear Stabilizer Bar (B) to Frame (1) using two hex

bolts (46), four washers (44), and two lock nuts (45). Tighten

hardware ﬁrmly but do not over tighten as deformation of the

stabilizer tube may occur

H. At this time make sure that the adjustable feet with lock nuts

are screwed fully into the stabilizer.

Assembly Manual

Assembly

Step 2

Ref. # Description Qty

1 Frame 1

29 Pop Pin Assembly for Head Tube 1

42 Handle Bar 1

7, 8, & 9 Seat Slider Assembly 1

51 Water Bottle Cage 2

Tools Required

3mm Hex 1

Adjustable wrench 1

A. Using your hand, grab the T-handle of the Pop Pin attached

to the seat tube of the frame. Turn the Pop Pin counter

clockwise for several revolutions to make sure it is free of

the securing threads and can be pulled freely.

B. Pull the entire seat slider assembly (7,8,9) from the frame

and reverse its direction. Reinsert the seat slider assembly

into the frame (with the holes facing the front of the bike)

while pulling out on the Pop Pin. Release the Pop Pin and

make sure it fully engages one of the holes provided in the

seat post.

C. Using the stamped steel combination wrench supplied,

loosen up the 14mm nuts that secure the saddle bracket

to the seat slider (8). Once loose, rotate the saddle so that

the nose of the saddle is facing the handle bars and is level

with the ground or in your desired position. Tighten the

14mm nut securely and manually attempt to twist the saddle

sideways to conﬁrm that it is secure before riding.

D. Remove the Pop Pin Assembly (29) from the small parts

bag and add some grease to the threads of the large

21mm nut that will screw into the head tube boss on the

bike.

E. Thread the Pop Pin Assembly (29) into the head tube boss

using a large adjustable wrench and tighten ﬁrmly.

F. Using your hand, grab the T-handle of the Pop Pin, turn it

counterclockwise for several revolutions to make sure it

is free of the securing threads and can be pulled freely.

G. Insert the handle bar (42) into the head tube of the bike

while pulling the Pop Pin out. Lower the handle bar to the

desired height and release the Pop Pin. Make sure the

Pop Pin fully engages one of the holes provided in the

handle bar. Turn the T-handle of the Pop Pin clockwise

until it is fully tightened, this will secure the handle bar

ﬁrmly at the desired height.

H. Using the 3mm hex tool supplied, mount the two water

bottle cages (51) to each side of the fork legs. The

necessary mounting screws have previously been installed

and must be removed from the fork legs prior to securing

the water bottle cage.

Assembly Manual

Step 3

Ref. # Description Qty

1 Frame 1

43 Pedals with Toe Clips & Straps (Left & Right) 1 Pair

Tools Required

Stamped Steel Combination Wrench 1

A. Remove Pedals (43) from the small parts box and look at the

ends of the pedal threads. You will notice that each pedal is

market with an “R” or an “L” on the very end of the spindle

past the threads. This mark indicates which side of the bike

the pedal is intended to mount. This is important since the

thread directions are different for each pedal.

B. Locate the Pedal that has the “R” on the spindle. This pedal is

for the right side crank arm of the bike (chain guard side) and

is right hand threaded (turn clockwise to tighten). It is a good

idea to apply grease to the threads before attaching them to

the crank, this will assure that they can be removed in the

future. Using the supplied Combination Wrench thread the

right Pedal on to the crank arm, tighten ﬁrmly.

C. Locate the Pedal that has the “L” on the spindle. Follow the

directions in step B. however, you will need to turn the spindle

left (counterclockwise) to tighten as the “L” spindle is reverse

threaded.

Assembly

Assembly Manual

Assembly/Initial Setup Adjustments

Step 4 - Final Inspection

A. Tighten all hardware.

B. Read warnings on machine.

Please read and refer to the Owner’s Manual for:

• Operating Instructions

• Maintenance Instructions

• Warranty Information.

To assure optimal performance and longevity, perform the following steps prior to placing your IC bike into

service.

A. Move bike into its ﬁnal location. Conﬁrm that all four feet are ﬁrmly in contact with the ﬂoor and that the bike is stable. If any of the

feet are not making full contact, it is recommended that you adjust them by turning the entire foot assembly counterclockwise which

will extend it further from the stabilizer bar. Once the foot is in full contact and the bike is stable, thread the jam nut clockwise until it

comes into contact with the stabilizer at the point the foot assembly threads in. Tighten the jam nut snug using an adjustable wrench.

This will secure the foot at the desired height.

B. With the resistance adjustment knob turned fully in the counterclockwise position (no brake contact with ﬂywheel), it is

recommended that you soak the brake pads with Schwinn®Fit-Tech Lube. This will extend the life of the brake pads and assure a

smooth resistance interface with the ﬂywheel.

C. Once the pads are lubricated, it is recommended that you tighten the resistance adjustment knob clockwise to tighten the brake

pads against the ﬂywheel surface. Do this until the brake pads are ﬁrmly clamped against the ﬂywheel. This will set the brake parts

and give the springs some initial compression. This process will also assure that the Fit-Tech Lube penetrates the entire brake pad

surface.

D. Conﬁrm that the Saddle is positioned in the desired location on the saddle mounting bracket. If the angle of the saddle or the fore/

aft position of the saddle needs to be adjusted, use the Combination Wrench to loosen the 14mm nuts on either side of the saddle

mounting bracket. This will allow you to adjust the tilt angle and fore/aft position of the saddle. Once in the correct position, tighten

both 14mm nuts on the saddle mounting bracket with the Combination Wrench.

That’s it! Initial set up is complete and you can now enjoy all these features and quality of your new Schwinn®

IC Bike!

Failure to visually check and test assembly before use can cause damage to the equipment.

It can also cause serious injury to users and bystanders.

Assembly Manual

Assembly

This page intentionally left blank.

Assembly Manual

Andere Handbücher für IC Pro

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Schwinn Heimtrainer Handbücher

Schwinn

Schwinn 140 Bedienungsanleitung

Schwinn

Schwinn A20 Recumbent Bike Bedienungsanleitung

Schwinn

Schwinn 126 Upright Bike Bedienungsanleitung

Schwinn

Schwinn 150 Upright Bike Bedienungsanleitung

Schwinn

Schwinn Airdyne AD2 Bedienungsanleitung

Schwinn

Schwinn NAUTILUS 113 Bedienungsanleitung

Schwinn

Schwinn Airdyne AD2 Bedienungsanleitung

Schwinn

Schwinn Fitness 123 Bedienungsanleitung

Schwinn

Schwinn U130i Bedienungsanleitung

Schwinn

Schwinn 170 Journey 1.5 Bedienungsanleitung

Schwinn

Schwinn 125 Bedienungsanleitung

Schwinn

Schwinn 206 Recumbent Bike Bedienungsanleitung

Schwinn

Schwinn Evolution Assembly Bedienungsanleitung

Schwinn

Schwinn Airdyne Bedienungsanleitung

Schwinn

Schwinn IC Pro Bedienungsanleitung

Schwinn

Schwinn IC7 Bedienungsanleitung

Schwinn

Schwinn 226 Recumbent Bike Bedienungsanleitung

Schwinn

Schwinn 170 Journey 1.5 Bedienungsanleitung

Schwinn

Schwinn AD2i Bedienungsanleitung

Schwinn

Schwinn Fitness 122 Bedienungsanleitung

Schwinn

Schwinn Fitness 231 Bedienungsanleitung

Schwinn

Schwinn 131 Upright Bike Bedienungsanleitung

Schwinn

Schwinn 130 Upright Bike Bedienungsanleitung

Schwinn

Schwinn A.C. Sport Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

Weslo

Weslo Vector 302 Kurzanleitung

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Pro-Form

Pro-Form 345 Zlx Bike Benutzerhandbuch

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Vision Fitness

Vision Fitness U70 Bedienungsanleitung