SciGene Hybex Bedienungsanleitung

www.scigene.com

1287 Reamwood Avenue, Sunnyvale, CA 94089 USA • Tel 408-733-7337 • Fax 408-733-7336 • [email protected]

Hybex®

Microsample Incubator

USER MANUAL

Cat. #1057-30-0 (115V) and 1057-30-2 (230V)

FOR RESEARCH USE ONLY

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 1 (408) 733-7337, [email protected]

Warranty

SciGene warrants that the Hybex® Microsample Incubator described in this manual shall be free of

defects in materials and workmanship for a period of 12 months from date of delivery. This warranty

does not cover removable blocks or accessories. In the event of a defect during the warranty period,

SciGene’s limit of liability will be to, at its sole discretion, provide replacement parts or replace the

product. The foregoing warranty is void in the event the unit was abused or modified or used in a

manner inconsistent with its intended purpose. SciGene makes no other warranty, expressed or implied

including warranties of merchantability and fitness for a particular purpose. In no event shall SciGene be

liable for any direct, indirect, special, incidental or consequential damagers or for any damages resulting

from loss arising out of or in connection with the sale, use or performance of the product.

SciGene Corporation, Sunnyvale, CA. All other trademarks used in this manual are the property of their

respective owners.

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 2 (408) 733-7337, [email protected]

Table of Contents

I. SAFETY NOTICES..............................................................................................................................................3

A. Intended Use ........................................................................................................................................................ 3

B. Instrument Safety................................................................................................................................................. 3

C. Symbols and Conventions .................................................................................................................................... 3

D. Warnings .............................................................................................................................................................. 4

E. Cautions................................................................................................................................................................ 5

F. Compliance........................................................................................................................................................... 5

II. UNPACKING AND SET UP.................................................................................................................................6

A. Unpacking the Heating Base ................................................................................................................................ 6

B. Items Provided ..................................................................................................................................................... 6

C. Environmental Requirements .............................................................................................................................. 6

D. Installing the Instrument...................................................................................................................................... 6

III. USING YOUR HYBEX SYSTEM ...........................................................................................................................7

A. Components, Controls and Accessories ............................................................................................................... 7

B. Handling Tube Blocks and the Waterbath Insert ................................................................................................. 8

C. Using the Temperature Controller ....................................................................................................................... 8

D. Calibrating the Temperature Controller............................................................................................................... 9

IV. MAINTAINING YOUR HYBEX SYSTEM.............................................................................................................10

A. Powering Off....................................................................................................................................................... 10

B. Cleaning the Instrument..................................................................................................................................... 10

C. Checking and Replacing Fuses............................................................................................................................ 10

V. TROUBLESHOOTING ......................................................................................................................................11

VI. SPECIFICATIONS ............................................................................................................................................11

VII. ORDERING INFORMATION.............................................................................................................................11

VIII. APPENDIX A – Using and Calibrating a Watlow SD31 Controller .....................................................................12

A. Using the Watlow SD31 Temperature Controller .............................................................................................. 12

B. Calibrating the Watlow SD31 Temperature Controller ...................................................................................... 12

IX. DECLARATION OF CONFORMITY....................................................................................................................13

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 3 (408) 733-7337, [email protected]

I. SAFETY NOTICES

A. Intended Use

The Hybex Microsample Incubator is intended for the heating and incubation of laboratory

samples. The instrument should only be used according to the instructions provided in this

manual. If the equipment is used in a manner not specified by the manufacturer (SciGene),

the protection provided by the equipment may be impaired.

La Hybex système est destiné pour le chauffage d'échantillons biologiques. L'instrument ne

devrait servir que selon les instructions fournies dans ce manuel de l'utilisateur et d'autres

documents techniques de SciGene. Si l'équipement est utilisé de manière non spécifiée par le

fabricant, la protection assurée par l'équipement peut être compromise.

B. Instrument Safety

Before operating the instrument, read the information in this section concerning hazards

and potential hazards. Ensure that anyone involved with the instrument’s operation is

instructed in both general safety practices for laboratories and specific safety practices for

the instrument.

Avant le fonctionnement de l'instrument, lisez les renseignements dans cette section

concernant les risques et les dangers potentiels. S'assurer que toute personne impliquée avec

le fonctionnement de l'instrument est instruit dans les pratiques générales de sécurité pour

les laboratoires et les pratiques de sécurité spécifiques pour l'instrument.

C. Symbols and Conventions

The following chart is an illustrated glossary of the electrical symbols that are used on the

Hybex Microsample Incubator. Whenever such symbols appear on instruments, please

observe appropriate safety measures.

Le tableau suivant est un glossaire illustré des symboles électriques qui sont utilisées sur le

système. Chaque fois que ces symboles apparaissent sur les instruments, veuillez observer les

mesures de sécurité appropriées.

1. Electrical Symbols

This symbol indicates that this is a protected ground terminal that must

be connected to earth ground before any other electrical connections

are made to the instrument.

Ce symbole indique qu'il s'agit d'un terminal de terrain protégé qui doit

être connecté à la terre avant que toutes les autres connexions

électriques sont apportées à l'instrument.

CAUTION: This symbol alerts you to consult this Operator’s Manual for

further information and to proceed with caution.

ATTENTION: Ce symbole vous avertit à consulter ce guide de l'utilisateur

pour plus d'informations et de procéder avec prudence.

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 4 (408) 733-7337, [email protected]

CAUTION: This symbol alerts you to an electrical hazard. Consult this

Operator’s Manual for further information and proceed with caution.

ATTENTION: Ce symbole vous avertit d'un risque électrique. Consultez ce

guide de l'utilisateur pour plus d'informations et de procéder avec

prudence.

This symbol indicates the OFF position of the main POWER switch.

Ce symbole indique la position OFF de l'interrupteur principal.

This symbol indicates the ON position of the main POWER switch.

Ce symbole indique la position ON de l'interrupteur principal.

2. Non-Electrical Symbols

CAUTION: This symbol illustrates a heat hazard. Proceed with caution when

working around these areas to avoid being burned by hot components.

ATTENTION: Ce symbole illustre un danger pour la chaleur. Faire preuve de

prudence lorsque vous travaillez autour de ces zones pour éviter d'être brûlé

par les composants du chauds.

CAUTION: This symbol alerts you to consult this Operator’s Manual for

further information and to proceed with caution.

ATTENTION : Ce symbole vous avertit à consulter ce guide de l'utilisateur

pour plus d'informations et de procéder avec prudence.

D. Warnings

Failure to comply with the following warnings that are affixed to the product can lead to

possible personal injury or death.

Défaut de respecter les avertissements suivants qui sont apposées sur le produit peut

conduire à possibles lésions corporelles ou la mort.

This symbol on the rear of the instrument indicates the presence of the fuse

box. Warning: For Continued Protection Against Fire, Replace Only with

Same Type Rating of Fuse. Always disconnect the power cord before

attempting to replace the fuse.

Ce symbole sur l'arrière de l'instrument indique la présence de la boîte de

fusibles. Avertissement : Pour le maintien de la Protection contre l'incendie,

remplacer uniquement avec la même cote de Type de fusible. Toujours

débrancher le cordon d'alimentation avant d'essayer de remplacer le fusible.

This symbol indicates the presence of hazardous voltage. Always disconnect

the power cord before servicing.

Ce symbole indique la présence d' une tension dangereuse. Toujours

débrancher le cordon d'alimentation avant l'entretien.

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 5 (408) 733-7337, [email protected]

E. Cautions

Failure to comply with the following cautionary statement affixed to the product may lead

to possible personal injury.

Omission de se conformer à la mise en garde suivante apposée sur le produit peut entraîner

des blessures possibles.

This symbol located both on and in front of the lid indicates the potential presence

of a Hot Surface. Use care when working in this area to avoid being burned.

Ce symbole situé sur et devant le couvercle indique la présence possible d'une

Surface chaude. Faire preuve de diligence lorsqu'il travaille dans ce domaine

pour éviter d'être brûlé.

F. Compliance

1. European Conformity (CE)

This symbol indicates the instrument is in compliance with all applicable

European Union Electromagnetic Compatibility and Low Voltage Directives.

2. Waste Electrical & Electronic Equipment Directive (WEEE)

WEEE is a European Community directive that became European Law in

February 2003. The crossed out wheelie bin symbol on a product or its

packaging indicates that it must NOT be disposed of with standard waste at the

end of its lifetime. Instead, it is your responsibility to return it to a designated

collection point for electronic equipment recycling. Contact your local SciGene

distributor for information on drop off locations.

3. Restriction of Hazardous Substances (RoHS)

The RoHS directive was adopted in February 2003 by the European Union. It

restricts (with exceptions) the use of six hazardous materials (including lead

and mercury) in the manufacture of various types of electronic equipment. All

SciGene instruments carrying the CE mark are also RoHS compliant.

4. Laboratory Equipment Standards

This symbol indicates the instrument meets Laboratory Equipment standards

UL 61010-1:2012 R04.16 and CAN/CSA-C22.2 61010-1:2012 + GI1 + GI2 as

certified by TÜV Rheinland of North America, Inc.

5. Electromagnetic Compatibility (EMC)

The Hybex System is a Class A digital device under FCC Title 47 Part 15B and

designated as Class A electrical equipment for measurement, control, and

laboratory use (EN61326).

Note regarding Canadian EMC compliance: Le present appareil numerique

n’emet pas de bruits radioelectrique depassant les limites applicables aux

appareils numeriques de class A prescrites dans le reglement sur le brouillage

radioelectrique edicte par le Ministere des Communications du Canada.

RoHS

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 6 (408) 733-7337, [email protected]

II. UNPACKING AND SET UP

A. Unpacking the Heating Base

The Hybex Microsample Incubator heating base is shipped on its side within the interior

carton. Remove any packing material around the unit and lift the unit out; taking care not to

damage the hinged cover. Carefully inspect the heating unit for damage. Heat blocks and

other accessories are packaged separately from the heating base.

If there is evidence of damage, retain the shipping materials and contact SciGene

([email protected]) or your local distributor for assistance.

B. Items Provided

The following items are included with the Hybex heating base within the

re-closable plastic bag:

•

Power cord

•

User Manual

C. Environmental Requirements

Ensure that the area where the incubator is installed meets the following conditions, for

reasons of safety and performance:

Ambient temperature +15 to +32°C (58 to 90°F)

Relative humidity 15 to 80% RH non-condensing

Air flow clearance 3 inches (8 cm) minimum on both sides

D. Installing the Instrument

1. Place the unit on a level surface within a few feet of the power source. Ensure the

lid can be opened completely without interference and leave 3 inches of clearance

along the back and sides for air circulation.

2. Plug the provided power cord into the back of the unit and then to a properly

grounded outlet. Use only the power cord provided.

Do NOT operate the system without a block inserted into the base unit!

Ne pas faire fonctionner le système sans un bloc insérée dans l'unité de base!

See Section VII. ORDERING INFORMATION for a list of available accessories and Section III.

B. Handling Tube Blocks and the Waterbath Insert for how to insert and remove blocks.

Allow 3 inches of

clearance on both sides

Allow 15 inches

of total vertical

clearance to fully

open the lid.

Allow 3 inches of

clearance at the back

for the power cord.

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 7 (408) 733-7337, [email protected]

III. USING YOUR HYBEX SYSTEM

A. Components, Controls and Accessories

Name Function

Power Switch Turns on main power to unit

Temperature Controller Used to set and observe block temperature

Heated Lid Heats the sealed air around the block

Temperature Probe Senses the temperature of the block

Heat Block Holds tubes or plates for heating

Microarray Incubation Chamber*For array hybridization (2 needed for operation)

Waterbath Insert*For heating buffers or water

Digital Thermometer* For calibrating system temperature

*Optional accessories

Microarray Incubation Chamber

Cat. #1057-38-0 (2/Kit)

Heat Block for 0.2 ml Tubes or Plate

Cat. #1057-31-0

Waterbath Insert

Cat. #1057-35-0

Digital Thermometer

Cat. #1051-52-0

Heated Lid

Power

Switch

Temperature

Probe

Temperature

Controller

Heat Block for Flat Bottom Microplate

Cat. #1057-39-0

Heat Block for 0.6 ml Tubes

Cat. #1057-33-0

Heat Block for 1.5 ml Tubes

Cat. #1057-34-0

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 8 (408) 733-7337, [email protected]

B. Handling Tube Blocks and the Waterbath Insert

Tube heating blocks and the waterbath insert are placed and removed from the heating unit

with the aid of two bolts (provided) that act as handles.

To properly install a block or insert:

1. Thread the two bolts several turns into the block.

2. Grasp the ends of the bolts, lift the block, and then carefully lower it into the unit;

guiding it over the temperature probe. The opening in the bottom of the block

should fit over the probe.

3. Remove the threaded bolts before using the system.

Do not operate the system without a block inserted into the base unit!

Ne pas faire fonctionner le système sans un bloc insérée dans l'unité de base!

When using a waterbath insert do NOT leave the heated lid in down position for

more than 90 minutes. Excess condensation will form that may damage the

heating base.

Lors de l'utilisation d'un insert de bain-marie ne pas laisser le couvercle chauffant en

position basse pendant plus de 90 minutes. L'excès de la condensation se forme qui

peut endommager la base chauffante.

C. Using the Temperature Controller

The Hybex Microsample Incubator is equipped with an

EZ-Zone temperature controller that has been calibrated

at the factory to provide accurate block temperatures

from 35 to 99°C. The controller has two LED displays and

four push buttons. The left display shows ACTUAL block

temperature in red. The right display shows the SET

temperature in green.

To program the temperature controller:

1. Turn on the instrument.

2. Program the desired SET temperature by pressing the up or down arrow buttons:

•Press the up arrow button to increase the current SET temperature

•Press the down arrow button to decrease the current SET temperature.

3. Verify the new SET temperature is shown in the green display on the right. The

instrument will now adjust the block heater until the SET temperature is attained.

SciGene recommends checking calibration according to your laboratory schedule. See

section III. D. Calibrating the Temperature Controller for details.

Hybex®Microsample Incubator — USER MANUAL

Version 1.9, Oct 2019 9 (408) 733-7337, [email protected]

D. Calibrating the Temperature Controller

The temperature controller is calibrated at the factory to provide accurate block

temperatures from 35 to 99°C. Calibration is required only if the controller displays a block

temperature which differs by more than one degree (1°C) from a NIST calibrated T-type

digital thermometer (sold separately, SciGene cat. #1051-52-0). Contact SciGene Customer

Service (custserv@scigene.com) or your local distributor to purchase a thermometer.

To calibrate the temperature controller:

1. Insert a block into the Hybex incubator, turn ON the

instrument and set the controller to 65°C. Allow 15

minutes for temperature to stabilize.

2. Using the cable provided with the digital thermometer

(cat. #1051-52-0), plug one end into the blue receptacle

found on the back panel of the Hybex incubator and

the other end into the thermometer.

3. Turn on the thermometer. Allow 1 minute for

thermometer to stabilize. The actual temperature of

the block will be displayed.

4. Calculate the difference between the digital

thermometer and the temperature controller to

determine the adjustment value. For example, if the

thermometer reads 63.9°C while the controller reads

65°C, then the adjustment value is -1.1°C.

5. On the controller, press the up and down arrows simultaneously for 3 seconds. The

left display shows “A1” and the right display shows “open”.

6. Press the Advance Button (green circle) 3 times until the right display shows “i.CA”.

The left display will show the offset value between the controller and thermometer

when the unit was last calibrated.

7. Using the up or down arrows, add the adjustment value from step 4 above to the

existing offset value shown on the controller. For example, if the adjustment value is

-1.1°C and the current offset is -0.3°C then the new offset is -1.4°C.

8. Press the Infinity Key (∞) twice to exit calibraon and return to the operaon

display. Verify that the temperature on the thermometer matches the display. Your

incubator is now calibrated to provide accurate temperatures between 35 and 99°C.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SciGene Zubehör Handbücher

SciGene

SciGene Hybex 1057-36-1 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung