Scotsman TC 180 Bedienungsanleitung
Installation Guide for Scotsman TC180 Dispenser
Installation Guide for:
Scotsman TC180 Ice & Water Dispenser
Installation Guide for Scotsman TC180 Dispenser
Unpacking
Remove the two banding strips securing equipment to pallet.
Remove cardboard carton and packaging material.
Inspect exterior of machine for any potential damage.
Remove from the front of the dispense area:
1 x water inlet tube
1 x drain tube complete with clip
Remove top panel and check position of failsafe ‘overflow’ bracket (magnet & sensor
should be aligned. Remove any ‘transit tapes’ present.
Check the ‘Ice dispense spout’ & ‘glass tray’ is correctly located.
Check ID on rear of machine for correct voltage, e.g. 230 volt 50 hz for UK use.
Remove protective film from outer panels.
Installation
Check that the following services are beneath & within 1 metre of machine location:
Counter top location for TC180
Dispenser to have services hole
cut at rear of unit to allow Water,
Waste and Electric services to be
fed down into connection points
underneath
(* See Next Page)
Installation Guide for Scotsman TC180 Dispenser
PLAN VIEW OF THE ‘TC180’ UNIT AND THE SUGGESTED POSITION FOR THE ‘CUTOUT’
THROUGH THE COUNTERTOP THE UNIT STANDS ON:
HOLE POSITION & SIZE
SUGGESTED:
150mm X 75mm
Installation Guide for Scotsman TC180 Dispenser
Example of under-counter TC180 service arrangement
POWER
WATER INLET
WATER DRAIN
HAND DISCONNECT
SWITCH
WATER
FILTER
WATER
VALVE
Electric –13 Amp Twin Socket or
Suitable 20 Amp Double pole
fused isolator.
Waste –Minimum 38mm
Trapped & Vented Drain, with ‘Air
Gap’ Fitting mounted on entry
Water –15mm Potable Water
supply terminated with a
Washing Machine 3/4BSP type
isolating valve (Note, Check valve
normally required prior to
isolating valve)
Installation Guide for Scotsman TC180 Dispenser
Services:
Cold water supply terminated with a ¾ BSP washing machine style stop
valve.
Mains drainage with a connection point lower then the drain outlet of the
machine. Connection point must be at least 1 ¼" diameter open and trapped
(similar to a domestic washing machine) with any connection made to include
a suitable ‘back flow’ prevention device to ‘EN1717’. If drain is too high, a
stand or condensate pump must be used.
13 amp socket outlet. (Due to potential high starting current, a socket adaptor
with other appliances should not be used.)
Note: If an external condensate pump is to be used, then 2 x 13 amp socket outlets
are required.
Check the following:
Ambient temperature - minimum 10°C, maximum 40°C
Adequate space at rear of machine for water and drain connections.
Minimum airflow clearance requirement of 15cm to both sides of machine.
Note:
If clearance is less, ice production rate will decrease by as much as 25% due to
potential overheating.
Fit 13 amp plug top (fitted with a 13A fuse) to equipment cable.
Fit water inlet hose to machine. Do not overtighten.
Fit flexible drain hose to drain fitting of machine and secure using clip
provided.
Note:
Both hoses are fitted with one straight end and one angled end. Use which ever is
the most suitable for that installation.
Connect water inlet hose to water supply. Do not overtighten.
Connect drain hose to main waste drain provided by inserting hose into
upstand (similar to domestic washing machine).
Note:
To prevent drainage problems caused by loops in the hose, reduce hose length as
far as reasonably practicable.
Installation Guide for Scotsman TC180 Dispenser
Start Up Procedure for TC180 Models
Remove the PCB inspection cover to view the LEDs of the unit
Turn on water and power supply
At this point, a GREEN LED will show and a RED LED flash for upto 3
minutes, water should enter the machine and begin to fill the water tank.
When the water tank is full, the float valve will stop incoming water with any
excess or overflow water possibly running out of the drain. Float may need
adjusting if water continues to overflow to drain.
The machine should start an ice making cycle (this after approx 3 minutes)
with the freezer assembly then the compressor in operation.
After approximately 2-3 minutes, ice should become visible & fall from the
chute/spout area and into the storage bin. The machine will then continue to
fill to the ‘bin level sensor’ level (approx. 1 hour for TC180)
Any set up issues or potential adjustments to settings for ice consistency
should be discussed with the engineer installing the equipment or Hubbard
Systems Technical Department in the first instance.
NOTE - The above procedures are designed to supplement guidance given in the
user handbook, not replace it.
HTG Trading Ltd (Hubbard Systems)
Unit 106 Claydon Business Park
Great Blakenham
Ipswich
Suffolk
IP6 0NL
T –01473 350045
Andere Handbücher für TC 180
6
Inhaltsverzeichnis
Andere Scotsman Eiswürfelbereiter Handbücher
Scotsman
Scotsman CSW45 Bedienungsanleitung
Scotsman
Scotsman Enodis DCE33 Installationsanleitung
Scotsman
Scotsman EC 106 Bedienungsanleitung
Scotsman
Scotsman MV 306 Bedienungsanleitung
Scotsman
Scotsman MDT6N90 Bedienungsanleitung
Scotsman
Scotsman Prodigy ELITE MC330 Bedienungsanleitung
Scotsman
Scotsman CME1856W Bedienungsanleitung
Scotsman
Scotsman MXG 327 Bedienungsanleitung
Scotsman
Scotsman CME1056 Bedienungsanleitung
Scotsman
Scotsman KDIL-PN-ID3 Bedienungsanleitung
Scotsman
Scotsman FM1500 Bedienungsanleitung
Scotsman
Scotsman CME1356 Bedienungsanleitung
Scotsman
Scotsman HID Service-Handbuch
Scotsman
Scotsman CM3 Bedienungsanleitung
Scotsman
Scotsman TC 180 Bedienungsanleitung
Scotsman
Scotsman F1322L Bedienungsanleitung
Scotsman
Scotsman Self Contained Cuber CU1526 Bedienungsanleitung
Scotsman
Scotsman NM1250 Bedienungsanleitung
Scotsman
Scotsman MAR 78 Bedienungsanleitung
Scotsman
Scotsman AFE325 Bedienungsanleitung
