SDC ZY7500 Series Bedienungsanleitung

SECURITY DOOR CONTROLS

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • Fax: (805) 494-8861

www.sdcsecurity.com • E-mail: [email protected]

P:\INSTALLATION INST\Electrified Lockset\INST-ZY7500 REV A 11-17 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email eng[email protected]

A. Door Preparation:

1. Measure desired height from finished floor, mark a horizontal line on door and door edge.

2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim

holes on template and mark only holes for lock function being installed.

3. Mortise door edge according to measurements on

installation template and drill proper holes for trim.

4. Recess for face plate, the dimension is:

L 8-1/32" x W 1-5/16" x D 7/32".

Height line

of lever

or knob

7/32"

INSTALLATION INSTRUCTIONS

ZY7500 SERIES MORTISE LOCK

of cylinder

of lockcase

of lever

or knob

Vertical centerline

Installation

template

Lof

door edge

P:\INSTALLATION INST\Electrified Lockset\INST-ZY7500 REV A 11-17 Page 2

B. Install Lockcase

Make sure the lock hand matches the door hand, use the following diagram to determine the hand of door.

Left Hand

LHRB

Left Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

Right Hand

RHRB

Right Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

1. Change latchbolt handing

If the hand of the latchbolt doesn’t match the door hand, remove the fixing screw and pull the latchbolt out from

lock case. Turn the latchbolt 180 ° to change the handling. Position latchbolt back, into case and fasten it.

Instructions for changing lock hand:

Remove screw

Pull out and turn

2. Change hand of lock

For RH and RHRB, the catch screw will be on the lock case side. For LH and LHRB, the catch screw will be on the

lock cover side.

P:\INSTALLATION INST\Electrified Lockset\INST-ZY7500 REV A 11-17 Page 3

3. Connect wires as shown on the lock cover diagram.

4. Insert lockcase into mortise cut-out and fasten screws to door.

1. Insert spindles as shown

D. Install Lever trim

1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation.

2. Install outside trim with mounting posts through door and position lever onto the spindle.

3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation.

4. Install inside mounting plate onto spindle. Tighten with provided screw.

5. Cap inside rose over mounting plate.

C. Install Spindles

B. Install Lockcase (Continued)

Reversible spring cage

Ferrule

Mounting post

Into Mounting post

P:\INSTALLATION INST\Electrified Lockset\INST-ZY7500 REV A 11-17 Page 4

1. Screw cylinder into threaded hole of lock case.

2. Tighten the setting screw against cylinder(s) by turning clockwise as shown.

3. Install face plate onto lock case front and fasten with supplied screws.

E. Install Cylinder and Armor Face Plate

USE THIS CAM.

D. Install Lever trim (continued)

6. Screw inside lever into position and tighten lever collar with supplied spanner wrench.

spanner wrench.

Spanner wrench

Inhaltsverzeichnis

Andere SDC Türschloss Handbücher

SDC

SDC TEMPLATE 180 SERIES Bedienungsanleitung

SDC

SDC 30-4-12 Bedienungsanleitung

SDC

SDC Z7800 Series Bedienungsanleitung

SDC

SDC S6200 Series Bedienungsanleitung

SDC

SDC Spacesaver 1091 ADMR Bedienungsanleitung

SDC

SDC Z7870 Bedienungsanleitung

SDC

SDC S6300 Series Bedienungsanleitung

SDC

SDC Z7200 Bedienungsanleitung

SDC

SDC Z7700 Series Bedienungsanleitung

SDC

SDC E75 Series Bedienungsanleitung

SDC

SDC FS23M Series Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC ZA7200 Series Bedienungsanleitung

SDC

SDC PD2090A Bedienungsanleitung

SDC

SDC Z7835 Series Bedienungsanleitung

SDC

SDC E75 Series Betriebsanleitung

SDC

SDC E75 Series Betriebsanleitung

SDC

SDC 30-4 Bedienungsanleitung

SDC

SDC FS23M Series Bedienungsanleitung

SDC

SDC SK-82 Bedienungsanleitung

SDC

SDC Z7200R Bedienungsanleitung

SDC

SDC S6100 Series Bedienungsanleitung

SDC

SDC EntryCheck 918 Bedienungsanleitung

SDC

SDC Z7600 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung