SDC Z7800 Series Bedienungsanleitung

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email eng[email protected]

A. Door Preparation:

1. Measure desired height from finished floor, mark a horizontal line on door and door edge.

2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim

holes on template and mark only holes for lock function being installed.

3. Mortise door edge according to measurements on

installation template and drill proper holes for trim.

4. Recess for face plate, the dimension is:

L 8-1/32" x W 1-5/16" x D 7/32".

Height line

of lever

or knob

7/32"

INSTALLATION INSTRUCTIONS

Z7800 SERIES MORTISE LOCK

of cylinder

of lockcase

of lever

or knob

Vertical centerline

Installation

template

Lof

door edge

OPTIONAL

DOOR CORE DRILLING GUIDE

#7000-DG

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 2

B. Strike Installation:

1. Align strike template on jamb. Be sure to keep 3/8" distance between lock centerline and strike

centerline. Recess 5/32" for flush fit of strike and dust box.

2. Mortise jamb according to measurement of strike template. Then fit strike and dust box into frame

and secure into place with supplied screws.

C. Install Lockcase

Make sure the lock hand matches the door hand, use the following diagram to determine the hand of door.

4-7/8"

3-17/32"

Strike

Lock C

3/8"

1" Holes

1-1/8" Deep

Jamb

Left Hand

LHRB

Left Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

Right Hand

RHRB

Right Hand

Reverse Bevel

INSIDE OF DOOR

OUTSIDE OF DOOR

2. Change hand of lock

For RH and RHRB, the catch screw will be on the lock case side. For LH and LHRB, the catch screw will be on the

lock cover side.

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 3

Pull out and turn

1. Change latchbolt handing

If the hand of the latchbolt doesn’t match the door hand, remove the fixing screw and pull the latchbolt out from

lock case. Turn the latchbolt 180 ° to change the handling. Position latchbolt back, into case and fasten it.

Instructions for changing lock hand:

C. Install Lockcase (Continued)

Remove screw

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 4

3. Connect wires as shown on the lock cover diagram.

4. Insert lockcase into mortise cut-out and fasten screws to door.

1. Insert spindle into outside hub of lock.

2. Insert inside spindle and tighten screw into outside spindle.

E. Install Lever trim

1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation.

2. Install outside trim with mounting posts through door and position lever onto the spindle.

D. Install Spindles

C. Install Lockcase (Continued)

Screw post

Reversible spring cage

Ferrule

Mounting post

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 5

6. Screw inside lever into position and tighten lever collar with spanner wrench.

3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation.

4. Install inside mounting plate onto spindle. Tighten with provided screw.

5. Cap inside rose over mounting plate.

1. Screw cylinder into threaded hole of lock case.

2. Tighten the setting screw against cylinder(s) by turning clockwise as shown.

3. Install face plate onto lock case front and fasten with supplied screws.

F. Install Cylinder and Armor Face Plate

E. Install Lever trim (Continued)

Spanner wrench

USE THIS CAM.

INSTALLATION WIRE DIAGRAM

Model 7800 Series 12/24VDC

STANDARD WIRING

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 6

COM

SECURE

UNSECURE

COM

LLS

DPS

REX

ORG

BRN

YEL

RED/YEL

RED/BLU

RED/GRN

VIO

GRY

PNK

BLK

GRN

12 VDC @ .6 AMP

WHT

RED RED

BLK

GRN

WHT

24 VDC @ .3 AMP

WIRING WITH OPTIONAL CABLE AND CONNECTOR

Dual Coil Solenoid Optional Monitoring

FROM LOCK

CABLE

LATCHED AND

LOCKED STATUS

DOOR POSITION

STATUS

REQUEST-TO-EXIT

OUTPUT

WHT/BLK

ORG/BLK

YEL/BLK

WHT

ORG

YEL

WHT/RED

ORG/RED

YEL/RED

COM

SECURE

UNSECURE

COM

LLS

DPS

REX

BLK

BLU

12 VDC @ .6 AMP

RED

WHT

BLK

BLU

24 VDC @ .3 AMP

RED

WHT

LATCHED AND

LOCKED STATUS

DOOR POSITION

STATUS

REQUEST-TO-EXIT

OUTPUT

Dual Coil Solenoid Optional Monitoring

FROM LOCK

P:\INSTALLATION INST\Electrified Lockset\INST-Z7800 REV D 10-13 Page 7

FAIL SAFE/FAIL SECURE CONVERSION

Procedure To Change SDC Fail Safe Solenoid To Fail Secure

Fail Safe Assembly

Fail Secure Assembly

Insert washer and spring onto rod tip assembly and screw into plunger until it bottoms out.

Insert plunger/rod tip into solenoid.

Fail secure

Solenoid body

Plunger

Spring

Washer

Rod tip assy.

Disassemble fail safe solenoid by

unscrewing rod tip assembly from plunger.

Fail safe

Rod tip assy.

Solenoid body

Plunger

Remove fail safe

solenoid

Spring and washer

supplied in case for fail

secure conversion.

Replace solenoid in holder as shown.

Inhaltsverzeichnis

Andere SDC Türschloss Handbücher

SDC

SDC Z7870 Bedienungsanleitung

SDC

SDC HiTower R7500 Bedienungsanleitung

SDC

SDC 1511S Bedienungsanleitung

SDC

SDC E75 Series Betriebsanleitung

SDC

SDC E75 Series Bedienungsanleitung

SDC

SDC 1190A Series Bedienungsanleitung

SDC

SDC Z7836 Series Bedienungsanleitung

SDC

SDC 180 Series Bedienungsanleitung

SDC

SDC S6300 Series Bedienungsanleitung

SDC

SDC E72K-A CIVIC SERIES Installationshandbuch

SDC

SDC Z7200 Bedienungsanleitung

SDC

SDC PRO Series Bedienungsanleitung

SDC

SDC Spacesaver 1091 ADMR Bedienungsanleitung

SDC

SDC Excel E1200 Series Bedienungsanleitung

SDC

SDC PD2090A Bedienungsanleitung

SDC

SDC EntryCheck E75 Series Bedienungsanleitung

SDC

SDC EntryCheck 918 Bedienungsanleitung

SDC

SDC Z7600 Series Bedienungsanleitung

SDC

SDC Z7200R Bedienungsanleitung

SDC

SDC E72 EntryCheck Bedienungsanleitung

SDC

SDC ZA7200 Series Bedienungsanleitung

SDC

SDC PBD2090A Bedienungsanleitung

SDC

SDC 1511S Bedienungsanleitung

SDC

SDC S6200 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung