Seagull Models CAP 232 Bedienungsanleitung
MadeinVietnam.
Kit features.
• Ready-made—minimalassembly&finishingrequired.
• Ready-coveredcovering.
• Photo-illustratedstep-by-stepAssemblyManual.
Specifications
Wingspan-------------------------------------57.1in--------------------------------145cm.
Wing area------------------------------------604.5 sq.in ---------------------- 39 sq.dm.
Approximate flying weight-----------------7.5 lbs-------------------------------- 3.4kg.
Length-----------------------------------------51.7in-------------------------------131.4cm.
Recommended engine size------------ .46 - .55 cu.in-------------------- 2-stroke.
.72 - .82 cu.in -------------------- 4-stroke.
ELECTRIC CONVERSION : OPTIONAL.
Radio System required 4 channels with 6 digital servos.
Flying skill level Intermediate/advanced.
“Graphics and specifications may change without notice”.
ASSEMBLY MANUAL
MS: SEA 97
CAP 232
CAP 232. Instruction Manual
2
INTRODUCTION.
ThankyouforchoosingtheCAP232 ARTFbySEAGULLMODELS.TheCAP232 wasdesigned
with the intermediate/advanced sport scale in mind. It is a semi scale airplane which is easy to fly
andquick toassemble.Theairframeisconventionallybuiltusingbalsa,plywood tomakeitstronger
thanthe average ARTF, yet thedesign allows the aeroplane tobe kept light.You will findthat most
oftheworkhasbeendoneforyoualready. Themotormounthasbeenfittedandthehingesarepre-
installed . Flying the CAP 232 is simply a joy.
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybeforestarting assembly of yourCAP 232.Usethepartslistingbelow to identify
all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it
is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplierandjoinyourlocalR/CModelFlyingClub.R/CModelFlyingClubsofferavarietyoftraining
proceduresdesignedtohelpthenewpilot on his way to successful R/C flight. They willalsobeable
to advise on any insurance and safety regulations that may apply.
ADDITIONAL ITEMS REQUIRED.
.46- .55 cu.in 2-stroke
.72- .82 cu.in 4-stroke
Radio System required 4 channels
with 6 digital servos.
Glow plug to suit engine
Propeller to suit engine
Protective foam rubber for radio
system
Silicone fuel line
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue
30 minute epoxy
5 minute epoxy
Hand or electric drill
Assorted drill bits
Modellingknife
Straight edge ruler
2mm ball driver
Phillips head screwdriver
220 grit sandpaper
90° square or builder’s triangle
Wire cutters
Masking tape & T-pins
Thread-lock
Paper towels
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage
(1) Canopy
WING ASSEMBLY
(1) Right wing half/ aileron
(1) Left wing half with/ aileron
(1) Aluminium dihedral brace
Tail section assembly
(1) Horizontal stabilizer/ elevator
halves.
(1) Rudder halves.
Some more parts.
HARDWAREPACK
COWLING
Landinggear.....
www.seagullmodels.com
3
1) Carefully remove the aileron from one
of the wing panels. Note the position of the
hinges.
2)Removeeachhinge from thewingpanel
and aileron and place a T-pin in the center of
each hinge. Slide each hinge into the wing
panel until the T-pin is snug against the wing
panel. This will help ensure an equal amount
ofhingeisoneither side of thehingelinewhen
the aileron is mounted to the aileron.
3) Slide the wing panel on the aileron until
there is only a slight gap. The hinge is now
centered on the wing panel and aileron.
Remove the T-pins and snug the aileron
against the wing panel.A gap of 1/64” or less
shouldbe maintained betweenthe wing panel
andaileron.
The control surfaces, including the
ailerons, elevators, and rudder, are
prehinged with hinges installed, but the
hinges are not glued in place. It is
imperativethat you properly adhere the
hingesin place per the stepsthat follow
using a high-quality thin C/A glue.
Note:
4)Deflect the aileron and completely
saturate each hinge with thin C/A glue. The
aileronsfrontsurfaceshould lightly contact the
wing during this procedure. Ideally, when the
hinges are glued in place, a 1/64” gap or less
will be maintained throughout the lengh of the
aileron to the wing panel hinge line.
Note: The hinge is constructed of a special
material that allows the C/A to wick or
penetrateanddistributethroughout the
hinge, securely bonding it to the wood
structureof the wingpanel and aileron.
To avoid scratching your new aero-
plane we suggest that you cover your work-
benchwith an oldtowel. Keep a couple ofjars
orbowlshandytoholdthesmallpartsafteryou
open the bags.
Pleasetrialfitallparts.Makesureyouhavethe
correct parts and that they fit and are aligned
properlybeforegluing!Thiswillensureproper
assembly as the CAP 232 is made from
natural materials and minor adjustments may
havetobemade. Thepaintandplasticparts
usedinthiskitarefuelproof.However,theyare
not tolerant of many harsh chemicals includ-
ingthefollowing:paintthinner,cyano-acrylate
glueaccelerator,cyanoacrylategluede-bonder
andacetone.Donotletthesechemicalscome
incontactwiththecoloursonthecoveringand
the plastic parts.
NOTE:
HINGING THE AILERONS.
5)Turnthe wingpanelover and deflect the
aileron in the opposite direction from the
opposite side. Apply thin C/A glue to each
hinge,makingsure that the C/Apenetratesinto
both the aileron and wing panel.
6) Using C/A remover/debonder and a
papertowel, remove anyexcessC/A glue that
may have accumulated on the wing or in the
aileronhinge area.
Hinge.
Hinge.
Hinge.
C/Aglue.
CAP 232. Instruction Manual
4
HINGING THE ELEVATOR.
8)Afterbothailerons are securely hinged,
firmly grasp the wing panel and aileron to
make sure the hinges are securely glued and
cannot be pulled out. Do this by carefully
applying medium pressure, trying to separate
the aileron from the wing panel. Use caution
not to crush the wing structure.
7) Repeat this process with the other wing
panel, securely hinging the aileron in place.
HINGING THE RUDDER.
Glue the elevator hinges in place using the
same techniques used to hinge the ailerons.
Glue the rudder hinges in place using the
same techniques used to hinge the ailerons.
Work the aileron up and down several
times to “work in” the hinges and check
for proper movement.
Note:
Aileron control horn installation: See pictures
below.
AILERON CONTROLHORN
M3LOCK
NUT.
ALUMINUMWASHER.
ALUMINUMWASHER.
CONTROLHORN
M3 SCREW.
18mm.
Epoxy.
Epoxy.
Hinge.
2 sets.
3x40mm.
Wing
bottom.
Aileroncontrol horn.
www.seagullmodels.com
5
ELEVATOR CONTROL HORN.
Install the elevator control horn using the
same method as with the aileron control
horns.
2 sets.
3x35mm.
Rudder control horn:
Using the same techniques used aileron
control horn. See picture below.
16mm.
2 sets.
3x35mm.
EPOXY.
Ruddercontrolhorn.
16mm.
Epoxy.
RUDDER CONTROL HORN.
Horizontal
Stabilizer.
Fuselage. Rudder.
Elevator control horn.
Hinge.
AluminumWasher.
CONTROL HORN M3
M3LOCKNUT.
Epoxy.
AluminumWasher.
CONTRONL HORN
M3 SCREW.
ALUMINUMWASHER.
ALUMINUMWASHER.
M3LOCK NUT.
EPOXY.
Horizontal
Stabilizer.
Fuselage.
Elevator.
Rudder.
CAP 232. Instruction Manual
6
3) Carefully bend the second nylon tube
up at a 45º angle. This tube is the vent tube.
1) Using a modeling knife, carefully cut
off the rear portion of one of the 3 nylon tubes
leaving 1/2” protruding from the rear of the
stopper. This will be the fuel pick up tube.
INSTALLING THE STOPPERASSEMBLY.
Thread locker glue.
4) Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using a
modeling knife. If flashing is present, make
sure none falls into the tank.
Important: When the stopper assembly is in-
stalled in the tank, the top of the vent tube
should rest just below the top surface of the
tank. It should not touch the top of the tank.
Carefully use a lighter or heat gun to
permenently set the angle of the vent tube.
See pictures below.Make yourself the
template of your engine on paper.
ENGINE MOUNT INSTALLATION.
Mark and drill 4 holes for engine mount.
Insert 4 blind nuts to firewall.
M4 x 30mm.
Vent tube. Fuel pick up tube.
Fuel fill tube.
2) Usinga modeling knife,cut onelength
ofsiliconfuel line. Connect oneend of theline
tothe weighted fuel pick up andthe other end
to the nylon pick up tube.(The silicon tube is
not included).
www.seagullmodels.com
7
5) With the stopper assembly in place,
the weighted pick-up should rest away from
therear of the tank andmove freely inside the
tank. The top of the vent tube should rest just
below the top of the tank. It should not touch
the top of the tank.
6) When satisfied with the alignment of
the stopper assembly tighten the 3 x 20mm
machine screw until the rubber stopper ex-
pands and seals the tank opening. Do not
overtighten the assembly as this could cause
the tank to split.
FUEL TANK INSTALLATION.
You should mark which tube is the vent
and which is the fuel pickup when you
attach fuel tubing to the tubes in the stopper.
Once the tank is installed inside the fuselage,
it may be difficult to determine which is which.
Rubber band.
Fueltank.
Fuel pick-up tube.
Fuelfill tube.
Venttube.
INSTALLING THE BATTERY.
Battery.
Tie Wrap.
Blow through one of the lines to ensure
thefuel lineshave not become kinked in-
side the fuel tank compartment. Air should
flowthrough easily.
1) Assembleand mountingthewheelpants
as shown in the following pictures.
WHEEL AND WHEEL PANTS
INSTALLATION.
2) Follow diagram below for wheel pant
installation:
CAP 232. Instruction Manual
8
1) Install the pushrod housing through the
predrilledholein the firewall andintothe servo
compartment. The pushrod housing should
protrude 1/4" out past the front of the firewall.
MakeaZ-Bend 1/4" fromoneend of theplain
wire pushrod.
MOUNTING THE ENGINE.
4) Remove the engine. Using an drill bit,
drill the mounting holes through the engine
mount at the four locations marked.
2) Place your engine onto the engine
mount. Adjust the engine is centered of the
edges of the engine case.
3) When you are satisfied with the align-
ment, mark the locations of the engine
mounting.
7mm.
C/Aglue.
LandingGear. wheel Pant.
wheel collar.
wheel.
Axle.
Washer. M3.
wheel Pant.
wheel.
M3.
M3.
wheel collar.
nut. Axle.
Washer.
M3.
12mm.
INSTALLING THE MAIN LANDING GEAR.
3) A drop of C/A glue on the wheel collar
screws will help keep them from coming lose
duringoperation.
Repeat the process for the other wheel.
4x20mm.
Lockerglue.
Lockerglue.
www.seagullmodels.com
9
6) AttachtheZ-Bend in thepushrod wire to
the throttle arm on the carburetor.
5) Bolttheenginetotheengine mountusing
the four machine screws. Double check that
all the screws are tight before proceeding.
2 mm diameter.
COWLING INSTALLATION.
MachineScrew M3x25mm
.
115mm.
Trim and cut.
Pushrodwire.
Trim and cut.
C/Aglue
CAP 232. Instruction Manual
10
MachineScrew M3x10mm
.
Aluminum spacers.
Aluminum tube.
M5 x 80mm.
M5 x 80mm.
M5nut.
Electric Conversion (Ep Power)
(OPTION).
Trim and cut.
Diameter=4mm.
Andere Handbücher für CAP 232
2
Inhaltsverzeichnis
Andere Seagull Models Spielzeug Handbücher
Seagull Models
Seagull Models Embraer EMB-312 Tucano T-27 Brazilian Air Force 85 span... Bedienungsanleitung
Seagull Models
Seagull Models Cessna L-19A Bird Dog Bedienungsanleitung
Seagull Models
Seagull Models Mini Nemsis EP Bedienungsanleitung
Seagull Models
Seagull Models SEA 324Y Bedienungsanleitung
Seagull Models
Seagull Models Extra 260 Bedienungsanleitung
Seagull Models
Seagull Models TWIN COMANCHE SEA134 Bedienungsanleitung
Seagull Models
Seagull Models De Havilland DH-60M Moth 72" wingspan... Bedienungsanleitung
Seagull Models
Seagull Models T-34C MENTOR Bedienungsanleitung
Seagull Models
Seagull Models EXTRA 330LX Bedienungsanleitung
Seagull Models
Seagull Models L-4 Grasshopper 90 inches Bedienungsanleitung
Seagull Models
Seagull Models Arising Star Bedienungsanleitung
Seagull Models
Seagull Models T-34 Mentor Bedienungsanleitung
Seagull Models
Seagull Models X-RAY Bedienungsanleitung
Seagull Models
Seagull Models SEA 304 Bedienungsanleitung
Seagull Models
Seagull Models CESSNA 188 AGWAGON Bedienungsanleitung
Seagull Models
Seagull Models PERCIVAL MEW GULL Bedienungsanleitung
Seagull Models
Seagull Models SEA 334 Bedienungsanleitung
Seagull Models
Seagull Models ultra-jet Bedienungsanleitung
Seagull Models
Seagull Models DECATHLON ARTF Bedienungsanleitung
Seagull Models
Seagull Models NIEUPORT 28 REPLICA Bedienungsanleitung
