Secure SSP 302 Betriebsanleitung

SSP 302

Socket Energy Monitor

User and Installation

Instructions

BGX501-921-01

out of range

controller cannot

communicate directly

with device

SSP Repeater

Z-Wave

Controller

Lamp Load

Secure SSP 302

Socket Energy Monitor

The Secure SSP 302 forms part of

a Z-Wave Plus™ home automation

network.

SSP 302 is a mains-powered,

plug-in device that supports energy

monitoring. It is suitable for

switching loads up to 3kW at 230V

AC. It can measure voltage,

Button

FLASH

current, power, energy etc. The

SSP 302 acts as a repeater in a

Z-Wave network and helps other

device messages to reach a

destination.

SSP 302 is a fully compliant

Z-Wave Plus™ device that will

work with other manufacturer’s

Z-Wave devices.

Installation

Step 1:

Unpack and

insert the

SSP 302 into

the wall socket.

Ensure that the

red-coloured

network status

LED is flashing (once per second).

Note:

If the network status LED is not

flashing check the following.

•Ensure wall socket switch is on.

•Press the top button, the relay

status LED should switch ON

and glow green.

•If the relay status LED does not

glow then the device is not

functioning.

•It is possible that the SSP 302

was part (joined) of another

network previously; if so, exclude

it before including it in this

network. Refer to step-2 for the

exclusion process.

Avoid locations alongside or behind

large metal surfaces that could

interfere with the low power radio

signals between the unit and the

controller.

Step-2: Z-Wave Plus™

commissioning

To include the

SSP 302 onto

a network, put the

controller into

inclusion mode.

Now, press and

hold the button on

SSP 302 for 4 to 7

seconds then

release. The network

FLASH

status LED will start flashing (twice

per second) on successful start of

inclusion process.

Note: Refer to the controller’s

manual for controller relevant

actions.

On successful inclusion the LED

will turn off.

The total process can take up to 20

seconds (Refer to the “Technical

specifications – Radio” section for

details).

If the device fails to join the

network it will go back to factory

default state and the Network

status LED will start flashing once

per second.

If there is an issue with RF

Communication, then re-locate the

device and repeat the

commissioning process again.

To exclude the SSP 302 from a

network, put the controller into

exclusion mode (refer to controller

instructions) and follow the same

sequence as per the

commissioning process for include

node. After successful exclusion

the network status LED will start

flashing once per second, and the

device will reset to factory default.

If exclusion fails, SSP 302 network

status LED will turn off after about

5 seconds.

Note: Exclusion works when the

device is in direct range with the

controller (no repeater allowed).

Associating SSP 302 in a

Z-Wave Network

(follow steps 3 to 5)

Note: Association process works

only after device included onto

network.

Step 3: Put the controller into

Association Mode.

Note: Some controllers can

automatically associate. Always

check with the manufacturer’s

manual.

Step 4: Press and hold the

SSP 302 button for more than 1

second, but less than 4 seconds,

and then release.

Step 5: The controller will confirm

association when the process is

successfully completed.

Combined

Button & LEDs

Green LED: ON

power switched to

front socket

Green

LED

*Socket type

will vary with

country

Appliance Socket

Press the SSP 302 button (less

than one second) to supply power

to its socket. By default, the green

LED will be lit when the supply is

On.

Inhaltsverzeichnis

Andere Secure Messgerät Handbücher

Secure

Secure Liberty 100 Produkthandbuch

Secure

Secure Elite 440 Bedienungsanleitung

Secure

Secure BGX501-806-R02 Bedienungsanleitung

Secure

Secure APEX 100 Bedienungsanleitung

Secure

Secure PADS-2 Bedienungsanleitung

Secure

Secure Liberty 100 Bedienungsanleitung

Secure

Secure Liberty EG4v12 Betriebsanleitung

Secure

Secure Premier 300 Gebrauchsanweisung

Secure

Secure Sprint 211 Bedienungsanleitung

Secure

Secure Premier 300 Bedienungsanleitung

Secure

Secure TRACKSO ELITE 103-2 Bedienungsanleitung

Secure

Secure Premier 211 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung