SENSIT Technologies HCN Programmierhandbuch

Quick-Start Instructions

IMPORTANT: After testing it may be

necessary to remove condensate collected

in the water/particle lter that is included

with the probe.

WARNINGS:

To prevent ignition of ammable or

combustible atmospheres, disconnect power

before servicing.

Always change batteries in an environment

free of combustible gases.

Do not handle the steel portion of any hot

air probe during or too soon after sampling.

It will become hot and retain heat and burns

may occur!

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.

MADE IN USA

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install the batteries by pushing down

the locking tab and sliding the handle

away from the top of the instrument. When

replacing handle be sure the tab is securely

in place.

2. IMPORTANT: CAREFULLY OBSERVE

POLARITY WHEN CHANGING BATTERIES.

Incorrect installation can damage an internal

“factory service only” fuse.

3. Locate button “A” – push & hold until

the unit powers up, then release the power

button.

4. Allow unit to go through the warm up

sequence in clean air. At the end of warm

up, the unit will auto zero and enter the

working display. This requires from 40 up

to180 seconds.

5. If FAIL is displayed for any of the sensor

readings, make sure the instrument is in

clean air; push and hold the “C” button until

AUTO ZERO is displayed. If this process

does not clear the fail on the display, this

could indicate a problem with the instrument

or sensor.

6. Look at the display – HCN (and optionally

CO) readings are displayed.

7. Alarms will activate at the preset limits.

8. Be sure the short tubing and lter disc are

attached to the back of the instrument.

9. When being used in excessively hot areas

attach the hot air probe assembly to the ¼

turn twist connection on the lter located on

the back of the instrument.

10. Place your nger over the inlet of the

probe and wait ~5 seconds for “FLOW

BLOCKED” to appear on the display. Check

for tight connections if it does not show

“FLOW BLOCKED”.

11. You are now ready to use the instrument.

You can now enter the area and detect gases.

12. When performing HCN/CO checks in

high temp areas do not exceed prolonged

exposures (over 5 min) at 500°F.

13. Press and hold the “C” button to zero

the instrument. (only in a gas free area).

14. When your investigation is complete

push button “A” and hold for 5 seconds until

the instrument displays “POWER OFF” then

release to shut off.

SENSIT®HCN

QUICK-START INSTRUCTIONS

Dieses Handbuch passt für folgende Modelle

Andere SENSIT Technologies Messgerät Handbücher

SENSIT Technologies

SENSIT Technologies GOLD EXCO+1200 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies CO Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-2 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies SPOD Kurzanleitung

SENSIT Technologies

SENSIT Technologies HXG-3 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Programmierhandbuch

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies VMD Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies SPOD C1D2 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies HCN Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-3P Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD 100 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies P400 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung