SENSIT Technologies HXG-2d Programmierhandbuch

Quick-Start Instructions

HINT: As you approach the source of the

leak, continue pressing the “B” button to

slow down the tick if it is rapidly increasing.

If the tick is no longer heard press the “B”

button to reset. Pressing the “A” button

deactivates the tick.

IMPORTANT: When replacing the

gooseneck into the clip on the right side,

wrap the gooseneck in a wide circular

manner counter-clockwise around the back

of the instrument. Bending in the opposite

direction may cause damage over the life of

the product.

WARNINGS:

To prevent ignition of ammable or combustible

atmospheres, disconnect power before servicing.

To reduce the risk of ignition of a ammable

atmosphere, batteries must only be changed in

an area known to be nonammable.

Do not mix batteries of different age or type.

Not for use in atmospheres of oxygen greater

than 21%.

ONLY zero instrument in a gas free environment.

To maintain intrinsic safety, service must be

performed by factory authorized technicians

with approved replacement parts only.

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.

MADE IN THE USA

WITH GLOBALLY SOURCED COMPONENTS

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install the batteries by removing the

retaining screw (torx) from the handle. Push

down the locking tab and slide the handle

away from the top of the instrument. When

replacing handle be sure the tab is securely

in place and replace the retaining screw.

2. IMPORTANT: CAREFULLY OBSERVE

POLARITY WHEN CHANGING BATTERIES.

Instrument will not function with improperly

installed batteries.

3. Locate button “A” – push & hold until the

unit powers up, then release the power button.

4. Allow unit to go through the warm up

sequence in clean air. At the end of warm

up, the unit will auto zero and enter the

working display. This requires from 40 up

to180 seconds.

5. If FAIL is displayed for any of the sensor

readings, make sure the instrument is in clean

air; push and hold the “C” button until Zro

is displayed. If this process does not clear

the fail on the display, this could indicate a

problem with the instrument or sensor.

6. Look at the display – PPM readings are

displayed. Readings above 990 PPM will

automatically range to LEL% as indicated by

the display icon on the right.

7. Extend the goose neck (the PPM/LEL sensor

and cap is at the tip).

8. You are now ready to use the instrument.

You can now enter the area and detect gases.

9. Once the environment is determined to

be safe to work in, if the source of an odor

needs to be located, press the “B” button to

hear a tick rate. Once an investigation is

begun, as the instrument is moved closer to a

combustible source, the tick rate will increase.

Press the “B” button again to reset the tick to

for a slower tick.

10. Press and release the “C” button to

activate a backlight for 30 seconds in

darkened environments.

11. Press and hold the “C” button to zero the

instrument. (only in a gas free area).

12. When your investigation is complete,

push button “A” and hold for 5 seconds until

the instrument displays “POWER OFF” then

release to shut off.

SENSIT®HXG-2d

QUICK-START INSTRUCTIONS

Andere SENSIT Technologies Messgerät Handbücher

SENSIT Technologies

SENSIT Technologies GOLD EXCO+1200 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies GOLD Programmierhandbuch

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies HCN Programmierhandbuch

SENSIT Technologies

SENSIT Technologies CO Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-3P Programmierhandbuch

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD 100 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-2 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HCN Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GLT Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies IRED Programmierhandbuch

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies SPOD C1D2 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies SENSIT-IT RAMP Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung