SENSIT Technologies IRED Programmierhandbuch

Quick-Start Instructions

NOTE: Start in a gas-free environment

IMPORTANT: Periodically test using known

samples of gas from 10ppm Ethane/1000ppm

Methane mix bottle.

WARNINGS:

To prevent the risk of ignition of a ammable

atmosphere, batteries must only be changed in

an area known to be non-hazardous.

To prevent ignition of ammable or combustible

atmospheres, disconnect power before servicing.

Substitution of components may impair intrinsic

safety.

Not for use in atmosphere of oxygen greater

than 21%.

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.

MADE IN THE USA

WITH GLOBALLY SOURCED COMPONENTS

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install a fully charged battery pack by aligning

the top of the battery with the latches in the

instrument housing. Lower the bottom of the

battery into place. Use the ¼ turn locking

screws to secure the battery pack in place.

2. Be certain the lter assembly has

a lter disc within the housing.

3. Locate button “A” – press & hold until the unit

powers up, then release the power button.

Charger cord must be unplugged from IRED.

4. Allowunittogothroughthewarmupsequence

in clean air. At the end of warm up, the unit will

perform a “cell check” and enter the working

display. This requires 20 to 25 minutes.

5. Look at the display – Ready for Measurement

and function indicators will be displayed.

6. Bump test the IRED with recommended

10ppm ethane/1000ppm methane

to verify accuracy. (optional)

7. Attach any probe to the lter

assembly (survey or barhole probe).

8. Place your nger over the inlet and wait ~5

seconds for “FLOW BLOCKED” to appear

on the display. If the instrument does not

show “FLOW BLOCKED,” service is required.

SENSIT®IRED

QUICK-START INSTRUCTIONS

9. You are now ready to use the instrument.

“For Best Results: Using a gas detection

device capable of sensing low level

natural gas concentrations, conrm

a gas measurement in a range of 50

- 2000ppm prior to use of the IRed”

10. Press the “B” button and follow the directions

on the display to perform a measurement.

The IRED will sample for 40 seconds and

update the display readings at 10 second

intervals. If sample concentration is too

large, the display will read “background

too high.” Back off the probe to dilute

the sample. It may be necessary to retest.

11. The “C” button allows you to view the

menu functions, turn the pump on or off,

and print the result after a measurement.

12. Measurements will automatically be stored

to the instrument’s memory with GPS

coordinates (GPS is an optional feature).

Measurements can be viewed on the

display of instrument or through Smartlink.

13. To Power Off or enter Stand By, press and

hold the “A” button for 5 seconds until the

instrument displays “POWER OFF” and

“STAND BY,” then release. Press the “A”

button to power off or the “C” button to put

IRED in “STAND BY.”

Andere Handbücher für IRED

Andere SENSIT Technologies Messgerät Handbücher

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Programmierhandbuch

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies SPOD C1D2 Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies P400 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-2d Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GLT Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD 100 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HXG-3P Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HCN Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Programmierhandbuch

SENSIT Technologies

SENSIT Technologies HCN Programmierhandbuch

SENSIT Technologies

SENSIT Technologies SPOD Kurzanleitung

SENSIT Technologies

SENSIT Technologies SENSIT-IT RAMP Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Bedienungsanleitung

SENSIT Technologies

SENSIT Technologies HXG-3 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Programmierhandbuch

SENSIT Technologies

SENSIT Technologies GOLD CGI Programmierhandbuch

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung