Shark Vancore Bedienungsanleitung

SHARK Vancore

SHARK Vancore - V01

Impose your

Shark

side!

CONTENT

• Anatomy of the helmet................................................ 5

• A helmet in your size .................................................. 6

• Chin strap : micrometric buckle .................................. 7

• Advice for use: put and remove .................................. 8

• Goggles, QRGS system, maintenance .....................9-10

• Textile parts : type, treatment, dismounting

and maintenance ................................................11-12

• Easy Fit .................................................................... 13

• SHARKTOOTH............................................................ 13

• Ventilation ................................................................ 14

• Warranty .................................................................. 15

• Legal informations ................................................... 16

Thank you for choosing a Vancore hel-

met. The Vancore is a top-quality helmet

that is ideal for use for urban and extra

urban area. The helmet complies with in-

ternational standards but does not purport

to guarantee total protection in all circums-

tances.

Make sure you carefully read all of the

following recommendations before using

the helmet. Just because you are wearing

a helmet does not mean you should neglect

driving carefully.

Standard: This Vancore helmet has

been approved and conforms to the ECE

R22/05 standard.

It therefore meets the requirements

imposed on all the countries that recognize

this standard in their territory.

WARNING! for French trafﬁc, the

Highway Code requires safety reﬂectors

(supplied separately in a packet) to be

ﬁtted in accordance with the enclosed

plan. In the United States and Canada,

speciﬁc regulations require that hel-

mets that only have ECE approval can-

not be used in these territories unless

they have acquired additional DOT

FMVSS 218 approval.

You can nd this user manual on our

web site:

www.shark-helmets.com

ANATOMY OF THE HELMET

1) Goggles

2) Top ventilation

3) QRGS (quick release goggles system)

4) Chip strap

5) Visor seal

6) Chin bar

7 - “Precise Lock“ buckle

XS 53/54

S55/56

M57/58

L59/60

XL 61

A HELMETS IN YOUR SIZE

For a helmet to provide effective pro-

tection while remaining comfortable, it has to

be perfectly suited to its user.

Choosing the correct size is essential.

Measure the circumference of your head

with a tape measure, positioning it about 2

cm above your eyebrows: this is where your

head is the largest. Once you have taken this

measurement, compare it to the table of sizes.

Try the size of Vancore helmet closest to the

measurement obtained, starting with the size

smaller than your head measurement.

If you feel that the contact is too hard, try

the size larger.

Your head should be held quite rmly but you

should feel no discomfort.

Tests for size must be carried out with the

chin strap tightened (please refer to the sec-

tion on page 8 for instructions on tightening the

chin strap). Check that you have good vertical

and horizontal visibility.

Check that your head can carry out all of

these movements without any particular dis-

comfort.

Check that when the chin strap is tightened,

the helmet cannot be removed from your head

when you try to move it forward by force. If

the helmet comes off or nearly comes off, it is

too big or else the chin strap is not correctly

tightened.

Keep trying on helmets until you nd the

ideal size.

WARNING! do not lend your helmet, even for

a short journey, if its size is not perfectly

suitable. For each use of your helmet, it is

absolutely necessary to make sure that the

helmet is well positioned on your head, and

that the chin strap is properly adjusted, fol-

lowing the instructions of this manual.

C D

A B

CHIN STRAP MICROMETRIC BUCKLE

ADVISE FOR USE

1/ Putting on the helmet

Once the chin strap is released, you have to

take hold of the two sections by the buckles

and hold them slightly apart to facilitate the

passage of your head. While carrying out this

movement, you are advised to keep the two

sections of the chin strap apart with your

thumbs so that they are properly positioned.

1 - Put the helmet rst against your neck (A).

2 - Then switch towards the front (B).

To remove, reverse operations

Position the protective parts of the chin strap

buckle correctly and fasten it in accordance

with the recommendations that are appro-

priate to the versions and country.

Check that the tension and therefore the posi-

tioning of the helmet are correct for all posi-

tions.

2/ Removing the helmet

Release the chin strap; hold the two sections

slightly apart as for putting the helmet on and

remove the helmet (D).

AB C

D E F

ADVICE FOR USE

HOLDING SYSTEM

Depending on the various versions and the

country concerned, your SHARK Vancore helmet

is equipped with a chin strap with a “Precise

Lock” rapid buckle with a snap lock. The “Pre-

cise Lock” snap lock system gives you precise

and accurate adjustment because of the consi-

derable length of its notched section. However,

it is essential on purchase to adapt the length of

the chin strap to your measurements. Adjust the

length of the strap using the adjusting buckle

(Figs. A, B, C and D)

Choose your Vancore and attach the holding

system. When the “Precise Lock” is adjusted to

the medium position, the chin

strap must be correctly tensioned under the chin

to hold the helmet rmly without causing you

any discomfort or pain.

To fasten the chin strap, all you have to do is to

thread the tongue into its place on the buckle

until tension is perfect (Fig. B).

The tongue connects and is automatically bloc-

ked. To release the chin strap, you have to pull

on the lever and remove the tongue from the

buckle. Although the notched tongue enables

you to change the adjustment precisely on each

use, it is important to check frequently that the

adjustment of the strap length is correct.

WARNING! never ride with the chin strap

loose or insufﬁciently tightened. Even

though the interior padding gives you the

impression of being held, your helmet risks

coming off in a fall. Never apply lubricating

or acid products or grease or solvents to the

chin strap buckle parts.

GOGGLES

The helmet SHARK Vancore must be exclusi-

vely used with glasses of protection SHARK

reference VZ 7400 approved according to

the European standard IN 1938 2010. Your

Vancore helmet has a pair of goggles Optic

by Carl Zeiss used as glasses of protection

for your eyes.

These goggles feature a double cylindrical

lens to obtain better visibility. The internal

display has a high performance anti-fog

treatment.

WARNING! the category of tint of glasses

VZ 7400 is of category 2 and are not

thus adapted to the driving in every case

where the visibility is reduced: at the

beginning or at the end of day, at nights,

weather of rain or fog.

MAINTENANCE

For protection and improve its life, the outer

surface of your goggles Vancore is anti-

scratch treated. When cleaning the lens, use

lukewarm water (below 40 degrees) and

a soft cloth in microber delivered with

goggles to wipe the lens. Neutral soap as

“savon de Marseille” can help you clean up.

WARNING! Never use any kind washing

windows (with alcohol or other solvent

type), these products can damage the

screen treatment.

GOGGLES

A B

C D

DISMANTLING

To unsettle the whole helmet, you just have

to take off the plastic part xed to elastic

bandages, the side part of goggles (A).

ASSEMBLY

Position the right strap xing on his pin (B).

Place the goggles in their nal position (C).

Attach the left strap xing on its pin using

dedicated buckle(D).

goggles • système qrgs

Inhaltsverzeichnis

Andere Shark Motorradzubehör Handbücher

Shark

Shark Evoline 3 Series Bedienungsanleitung

Shark

Shark Nano Bedienungsanleitung

Shark

Shark SKWAL Bedienungsanleitung

Shark

Shark ATV-DRAK Bedienungsanleitung

Shark

Shark RSR2 Bedienungsanleitung

Shark

Shark Vision-R Bedienungsanleitung

Shark

Shark SX 2 Bedienungsanleitung

Shark

Shark S 800 Bedienungsanleitung

Shark

Shark Race-R PRO Bedienungsanleitung

Shark

Shark Evo-One Bedienungsanleitung

Shark

Shark RSJ Bedienungsanleitung

Shark

Shark RACE-R PRO GP 06 Bedienungsanleitung

Shark

Shark Vantime Bedienungsanleitung

Shark

Shark EVO-ONE 2 Bedienungsanleitung

Shark

Shark VARIAL Bedienungsanleitung

Shark

Shark RSF 2 RACE Bedienungsanleitung

Shark

Shark Spartan Carbon Bedienungsanleitung

Shark

Shark RIDILL Bedienungsanleitung

Shark

Shark SPEED-R Bedienungsanleitung

Shark

Shark Evoline 3 Series Bedienungsanleitung

Shark

Shark EvoLine Bedienungsanleitung

Shark

Shark SK Bedienungsanleitung

Shark

Shark RIDILL Bedienungsanleitung

Shark

Shark D-SKWAL 3 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung