Sharkoon T9 Bedienungsanleitung
Manual
T9
Content
1. Features
2. Package content
3. The case at a glance
4. Installation of a mainboard
5. Installation of a PSU
6. Installation of a HDD
7. Installation of an optical device
8. Installation of a 3.5" device
9. Installation of an add-on card
10. The pre-installed fans (Value edition only)
11. Installation of additional fans / optimized airflow
Dear customer!
Congratulations for purchasing this premium quality SHARKOON product.
For a long life time and to take full advantage of this product we recommend you to read this
manual completely.
Have a good time with our product!
SHARKOON Technologies GmbH
T9
1. Features
• ATXcase
• 9x5.25"drivebays
• FrontI/O(Valueedition):1xUSB3.0,3xUSB2.0and2xaudio
• FrontI/O(Economyedition):4xUSB2.0and2xaudio
• 7slotsforadd-oncards
• Meshfrontpanel
• Quickfastenersforopticaldrives,mainboardmountingpanelwithinstallationopening
for coolers
• 2openingsforwatercooling
• Cablemanagementsystem
• Fanconguration:
Value edition Economy edition
Case front
2x120mmfanwithLEDas
well as 3-pin and 4-pin
connector (pre-installed)
1x120mmfan(optional)
Side panel Acrylic 2x120mmfans(optional)
Rear panel
1x120mmfanwithLEDas
well as 3-pin and 4-pin
connector (pre-installed)
1x80mmor120mmfan
(optional)
• Dimensions: 475x200x440mm(LxWxH)
• Weight: ~6.6kg
2. Package content
• PCcase“T9Value”or"T9Economy"
• Screwkit:
Screws for mainboard
mounting
Screws for PSU moun-
ting
Screws for drive moun-
ting (3.5" and 5.25") Screws for HDD mounting
T9
• Accessorykit:
Stand-offs for mainboard Washers Lockattachment(A)andspeaker(B)
MountinganglesforHDDs(decoupled/A)and
3.5"devices(notdecoupled/B)
Quickfastenersforopticaldrives 5.25" bezel with 3.5" opening
Note:
If you are missing any of the items listed above, please contact our customer service
immediately:
suppor[email protected] (international).
T9
3. The case at a glance
Front view
A– FrontI/O(Valueedition):
a – PowerLED
b – USB3.0connector
c – USB2.0connectors
d – Audio connectors
e – PowerandHDDLED
B – FrontI/O(Economyedition):
a – PowerLED
b – USB2.0connectors
c – Audio connectors
d – PowerandHDDLED
C – 5.25" drive bays
D– covered:pre-installed120mmfans(Valueedition)
Side view (closed/left)
A – T9Economyedition
a – Bracketsfortwo120mmfans
B– T9Valueedition
b – Acrylic side panel
ab
A
A
B
B
C
a
a
b
b
c
c
D
d
d
e
T9
Side view (opened/left)
A – Drive bays for 5.25" devices
B– Mainboardmountingpanelwith:
a – Installation opening for CPU
coolers and
b – Cable management system
Backsideview
A – Opening for I/O shield
B– Pre-installed120mmfan(Valueedition)
C – Slot bezels
D – Openings for water cooling
E– PSUbracket
F – Thumb screws
Bottomview
A – Case feet
B– AirintakeforPSU
Note:
For more information on how to install the intended devices, refer to their respective
documents.
A A
AA
B
a
b
A
A
B
B
C
D
E
FF
F
F
T9
4. Installation of a mainboard
1. Open the case by loosening the thumb screws on the case’s back side and removing the left
sidepanel.Laydownthecasesidewiseonanevensurface.
2.The mainboard’s mounting panel inside the case provides various drillings to x the
stand-offs(g.1).
g.1
Themainboardcontainsspecialscrewopenings(g.2).
g.2
Place the mainboard to the mounting panel. A stand-off must be screwed into every
drilling of the mounting panel visible through the mainboard’s screw openings.
T9
3. Remove the mainboard and screw the stand-offs into the respective drillings of the
mountingpanel(g.3).
(Stand-offs)
g.3
4. Press the I/O shield (delivered with the mainboard) into the I/O shield opening in the case’s
back side.
5.Placethemainboardbackontothestand-offsandscrewthemainboardtothem(g.4).
(Screws for mainboard mounting)
g.4
T9
6. Plug the connectors of the case’s front bezel to the respective connectors of the mainboard
(also refer to your mainboard’s manual for further information).
Note:
The eSATA cable connected to the front eSATA connection should not exceed 50 cm of
length otherwise transmission errors may occur! With premium quality eSATA cables this
maximum length may be exceeded.
5. Installation of a PSU
1. Set up the case in front of you and put the PSU from the inside against the PSU bracket on
thecase’sbackside(g.5).
g.5
2.ScrewthePSUtothecasefromtheoutside(g.6).
(Screws for PSU mounting)
g.6
T9
6. Installation of a HDD
1. Remove the case’s right side panel.
2.AttachthedecoupledmountinganglestotheHDDfrombothsides(g.7).
(Screws for HDD mounting)
(Decoupled mounting angles)
g.7
3. Slide the HDD with attached mounting angles into the case’s respective drive bay and
screwitfrombothsides(g.8).
g.8
4. Connect the HDD to the power supply and the mainboard.
Inhaltsverzeichnis
Andere Sharkoon Gehäuse Handbücher
Sharkoon
Sharkoon S1000 Bedienungsanleitung
Sharkoon
Sharkoon Skiller SGC1 RGB Bedienungsanleitung
Sharkoon
Sharkoon DG7000-G RGB Bedienungsanleitung
Sharkoon
Sharkoon AI7000 Glass Bedienungsanleitung
Sharkoon
Sharkoon TG7M RGB Bedienungsanleitung
Sharkoon
Sharkoon ELITE SHARK CA700 Bedienungsanleitung
Sharkoon
Sharkoon TG6 Bedienungsanleitung
Sharkoon
Sharkoon Swift Case Pro Combo Bedienungsanleitung
Sharkoon
Sharkoon REBEL C50 RGB Bedienungsanleitung
Sharkoon
Sharkoon TAREA Bedienungsanleitung
Sharkoon
Sharkoon REBEL C70M Bedienungsanleitung
Sharkoon
Sharkoon TG5 Bedienungsanleitung
Sharkoon
Sharkoon Elite Shark CA300H Bedienungsanleitung
Sharkoon
Sharkoon Nightfall U3 Bedienungsanleitung
Sharkoon
Sharkoon V1000 Bedienungsanleitung
Sharkoon
Sharkoon TG5 Pro RGB Bedienungsanleitung
Sharkoon
Sharkoon REX8 Series Bedienungsanleitung
Sharkoon
Sharkoon Rapid-Case 2.5" USB 3.1 Type C Bedienungsanleitung
Sharkoon
Sharkoon RGBFLOW Bedienungsanleitung
Sharkoon
Sharkoon TG4 Bedienungsanleitung
