Sharp EC-12TWT9 Bedienungsanleitung

SHARP

OPERATION MANUAL

VACUUM CLEANER

Model

EC-14TWT6

EC-14TAT6

EC-12TWT6

EC-12TWT4

EC-12TWT2

EC-12TXT2

EC-12SXT4B

I CONTENTS PAGE I

•IMPORTANT SAFETY INSTRUCTIONS...2

•PARTS IDENTIFICATION ...................... 4

•SPECIFICATIONS ................................... 4

• OPERATING INSTRUCTIONS., ............. 5

•MAINTENANCE INSTRUCTIONS .......... 8

•REPLACEMENT INSTRUCTIONS ..... 10

•BEFORE REQUESTING SERVICE ..... 14

•DESCRIPTION OF ACCESSORIES ...15

•LIMITED WARRANTY .......................... 16

Thank you very much for buying SHARP

Before using your SHARP vacuum cleaner,

please read this operation manual carefully to

obtain the best use from your vacuum cleaner.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical vacuum cleaner, basic precautions should always be

followed including the following:

Read all instructions carefully before using this vacuum cleaner.

WAR NING/Toreduce the risk of fire, electric shock, or injury:

1 Electric shock could occur if used outdoors or on wet surfaces°

2Do not leave unattended when plugged in. Unplug from outlet when not in use

and before user-servicing.

3Close supervision is necessary when used by or near children.

Do not allow to be used as a toy.

Use only for intended use as described in this manual.

Use only the manufacturer's recommended attachments and paper bag.

Never operate this vacuum cleaner if it has a damaged cord or plug, if it is not

working properly, if it has been dropped, damaged, exposed to weather or

dropped into water.

Return the vacuum cleaner to a Sharp Authorized Service Dealer or Station in

the United States for examination and repair.

Do not pull or carry this vacuum cleaner by the power cord. Do not use the

power cord as a handle, close a door on the cord, or pull the cord around sharp

edges or corners. Keep cord away from heated surfaces.

Do not run this vacuum cleaner over the cord.

7 Never disconnect the plug by pulling on the cord. To disconnect from an

outlet, grasp the plug, not the cord.

8Never operate this vacuum cleaner with any air opening blocked. Keep the air

openings free of dust, lint, hair and any other similar material.

When the secondary filter becomes dirty, rinse in warm water. Filters should

be completely dry before reusing.

9Never drop or insert any object into any opening.

10Keep hair, face, fingers and loose clothing away from any openings, such as

--the agitator and all moving parts.

11Do not pick up lit cigarettes, hot ashes, matches or similar materials, razor

blades, needles, pins or other sharp objects.

12Never operate this vacuum cleaner without a paper bag and filters in place.

13Before removing the plug from the outlet, turn all controls to the "OFF" position.

1 4 Use extra caution when cleaning on stairs.

15Never handle plug, cord or vacuum cleaner with wet hands.

1 6 Do not touch the, agitator while it is rotating.

17Do not use in presence of flammable or combustible liquids or fumes.

18 Do not place heavy objects on the vacuum cleaner.

19Do not step, on the hose or pull the hose forcibly'.

2{) Do not pick up large objects such as waste paper or cloth which may clog

the hose.

21 Do not expose this vacuum cleaner to high temperatures while operating

or during storage.

_)2 Store this vacuum cleaner in a dry place.

23use the carrying handle at the back of the body to carry this vacuum

cleaner.

24 Before servicing this vacuum cleaner, allow all metal parts to cool first.

i i m

iiiii ii i

CAUTION: To reduce the risk of electric shock, this vacuum cleaner has a polarized plug "_

I(one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the J

IPlug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact aqualified

1_electrician to install the,,proper outlet. Do not change the plug in any way.

SAVE THESE INSTRUCTIONS

This vacuum cleaner is intended for household use only.

PARTS IDENTIFICATION

( FRONT ")

Power Cord __

Panel __ /1_

Power Control--_

(EC-14TWT6/ "_7--

14TAT6/12TWT6 /Y_

only) _

Dust indicator--/ J_

(EC-14"rw'r6/ i',/'_

14TAT6/12TWT6 _"

only) j

Clamp Knob ..

Headlight

(Except

EC-12TXT2/

12SXT4B

Bumper

RUG/FLOOR Selector

(EC-14TWT6/14TAT6 only)

ON/OFF Switch

L. REAR

Cord Storage

Hooks

Handle Screw

Carrying Handle

Extension Wand

and Crevice Tool

Packed in the box;

assemble by placing

crevice tool inside

wand as shown.

Clip wand into place.

C-q-'--'-_'_:::zZ3

Suction Hose

Upholstery Tool with

Detachable Brush

Foot Pedal Release

SPECIFICATIONS /

EC-14TWT6

EC-14TAT6

EC-12TWT6

EC-12TWT4

EC-12TWT2

EC-12TXT2

_EC-12SXT4B

INPUT

(AMP)

12.0

10.0

9.0

8.5

POWER

CONTROL

YES

HEADLIGHT DUST

iNDICATOR

YES

I NO

YES

NO j

CORD LENGTH

(Ft.)

WARNING:

Operate vacuum cleaner only at the voltage specified on nameplate.

OPERATING INSTRUCTIONS

HOW TO ATTACH THE HANDLE TO VACUUM CLEANER

First remove the handle screw.

Then insert the base of the handle into

the top of the body' of the vacuum cleaner

as shown. (Fig. 1)

Handle

Fig.1

i , n

12Line up the small hole on the handle

with the small hole on the rear of the

vacuum cleaner and insert the screw.

(Fig. 2), Be sure the screw is tightened

securely.

Handle screw Fig.2

HOW TO WIND POWER CORD

1Insert the power cord

in the clip located on

the upper cord storage

hook as shown. (Ficj.3) Clip

side

Fig.3

2Wrap excess cord

around the cord stor-

age hooks to prevent

dragging and any inter-

ference with cleaning.

(Fig. 4)

Upper cord

storage hook Fig.4

HOW TO RELEASE POWER CORD

rRotate the upper cord storage

hook downward for quick cord

release. (Fig.5)

Upper cord

storage hook

Fig.5

OPERATING INSTRUCTIONS /

ON/OFF SWITCH

Ir 1To turn on the vacuum cleaner, touch

the switch on the appliance to the

=ON" position. (Fig. 6)

2To turn off the vacuum cleaner,

touch the switch to the "OFF" posi-

tion. (Fig. 7)

Fig.6

POWER CONTROL SWITCH (EC-14TWT6/14TAT6/12TWT6 only)

A slide switch allows selection of any cleaning

power from low "L" to high "H". To increase the

suction power, slide the switch toward the "H"

position.

To decrease the suction power, slide the switch

toward the "L" position. (Fig. 7)

Power Control Knob

HIGH:

Greatest suction powe_r for heavy vacuuming

jobs. Medium power levels may be set

between "H" and "L".

LOW:

Low suction power for delicate cleaning jobs.

•|1 iii

Fig. 7

DUST INDICATOR (EC-14Tw'r6/14TAT6/12TWT6only)

#..-

When the indicator enters the red area, re-

place the full paper bag with a new genuine

Sharp TWIN PLY_Micro-Filtration paper bag.

(Fig. 8)

NOTE:

Dust Indicator

Red area 00000000 Fig. 8

If the vacuum cleaner takes in excessive amounts of fine dust, the indicator may

enter the red area even if the paper bag is not filled,.

If the vacuum cleaner takes in excessive amounts of fiber (thread, cottony material

etc.), the indicator may not enter the red area even if the paper bag is filled.

Should either of the above occur, it is recommended that the paper bag be replaced with

a Sharp TWIN PLYTMnew paper bag.

i | II I

RUG/FLOOR SELECTOR (EC-14TW'r6/14TAT6 only)

The RUG /FLOOR selector should only be

adjusted while the vacuum cleaner is in the

"ON" and in the upright position.

1When cleaning carpets, slide the selector to

the "RUG" position.

2When cleaning bare floors, slide the selector

to the "FLOOR" position. (Fig. 9)

NOTE:

Make sure The RUG /FLOOR selector is set

to either the extreme front or the extreme back

to avoid any problems that may occur.

Fig. 9

HOW TO ADJUST THE HANDLE

The handle of this vacuum cleaner can

be set to either of three positions-Up-

right, Normal or Parallel.

To release the handle, depress the pedal

at the left rear corner of the vacuum

cleaner. (Fig. 10)

Upright position

Normally the handle is locked in this position

for storage or when using the On Board

Tools. By pushing the handle forward until

the handle is locked, this vacuum cleaner

will stand on its legs and wheels. (Fig. 11)

Pedal __

Legs

Fig. 10

Fig. 11

i,i

Normal position

This position is used for normal cleaning.

(Fig. 12)

Fig. 12

Parallel position

This position is used for cleaning under furni-

ture.

To get to the Parallel position, depress the

pedal again. (Fig. 13)

EDGE CLEANING

This model has "Edge Cleaning " for the cleaning of carpet

edges near baseboards and stationary furniture. /

(EC-14TWT6 and 14TAT6 have edge cleaning with brush.) _)

Fig. 13

MAINTENANCE INSTRUCTIONS

Unplug this vacuum cleaner from the electrical outlet before servicing. •

HOW TO CHANGE THE PAPER BAG

rWhen operating the vacuum cleaner, always use genuine Sharp TWIN PLY TM Micro -_

Filtration paper bags.

1Push down on the clamp knob located

on the top of the dust cover and pull the

dust cover forward. (Away from the unit.)

(Fig. 14)

_---- Clamp knob

Dust cover

Fig. 14

2To remove the paper bag, grasp the col-

lar on the bag and pull it out. (Fig. 15)

Paper bag

Fig. 15

3Insert the new bag by pressing the collar

opening completely around the suction

inlet..(Fig. 16)

Collar

Fig. 16

4Spread out the sides of the new bag.

(Fig. 17)

__1. L,,_._, Fig. 17

HOW TO CHANGE THE SECONDARY FILTER

fThe secondary filter consists of an electrostatic

micron filter and subfilter. The filter should be

replaced at least every 10 months to keep the

micron filter highly efficient.(EC-14TWT6/14TAT6/

12TWT6/12TWT4 only)

When the secondaryfilter becomes excessively soiled,

wash with water and replace after it iscompletely dried.

(EC-12TWT2/12TXT2/12SXT4B only)

1First unplug the vacuum cleaner from the electri-

cal outlet. Remove the secondary filter from the

bottom of the paper bag compartment (Fig. 18) by

lifting it out from under the retaining lip as shown.

2Install the new filter as shown in Fig. 19.

3 Make sure that the secondary filter is in place

before vacuuming.

Secondary

filter

Fig. 18

Sub filter

Micron filter

(EC-14TWT6/

14TAT6/

12TWT6/

12TWT4 only)

Retaining lip

Fig. 19

HOW TO CLEAN 'THE SUCTION HOSE

When a clog occurs,:

o ,u0t o o00 c,0aoor,ro ..oe,eo.r, a,'iIi

=outlet, place the vacuum cleaner in the Upright

position.

Hold the connection tube of the suction hose in

•_ one hand and the handle in the other. Then pull

out the connection tube from the suction pipe of

the nozzle head.(Fig. 20)

3 Remove the clog carefully without damaging the

suction hose.

/11 After the clog is removed, insert the suction hose

into the suction pipe and turn on the vacuum

cleaner to check that the clog has been removed.

Suction hose

Nozzle head

-- Suction pipe

Connection tube

Fig. 20

REPLACEMENT INSTRUCTIONS

HOW TO REMOVE THE BOTTOM PLATE

Before replacing any parts, unplug the

vacuum cleaner from the electrical outlet. To

replace any of the following parts, set the

handle to the Parallel position.

Then turn the vacuum cleaner over, expos-

ing the underside.

Loosen the bottom plate by sliding the latch

away from the mounting screw. (Fig. 21)

Then remove the bottom plate. ILatch /,oon,,oO

screw

Fig. 21

HOW TO REPLACE THE HEADLIGHT LAMP

(EC-14TWT6/14TAT6/12TWT6/

12TWT4/12TWT2 only)

i ii

Remove the headlight mounting screws..

(Fig. 22)

Note the arrangement of the lead wires and

then carefully lift out the headlight assem-

bly. (Fig. 23)

.Remove the lamp from the socket by push-

mg in gently and turning it counterclockwise.

(Fig. 23a)

Install the new lamp by pushing it gently

into the socket and turning clockwise. (Fig.

23b)

Use any standard bayonet base vacuum

cleaner lamp rated 125V, 20W.

® ®

Headlight mounting Screws

Headlight assembly Fig. 22

Fig. 23a Fig. 23b

5 Reinsert the headlight assembly.

Secure it with the mounting screws.

Lamp Socket

Fig. 23

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sharp Staubsauger Handbücher

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch