Shuttle HOT-681 Bedienungsanleitung

HOT-681

PPGACeleronprocessor

Based AGP MAIN BOARD

User's Manual

- 2 -

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accor-

dance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office.

Washington, DC 20402, Stock 004-000-00345-4

FCC Warning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate this equipment.

Note : In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded

cables and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic

compatibility :

- Immunity in accordance with EN 50082-1: 1992

- Emissions in accordance with EN 55022: 1987 Class B.

NOTICE

Manual Ver 1.0

All information, documentation, and specifications contained in this manual are subject to change without prior

notification by the manufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does

it make a commitment to update the information contained herein.

TRADEMARKS

Intel is a registered trademark of Intel Corporation

PPGA Celeron Processor is a registered trademark of Intel Corporation

PC/AT is a registered trademark of International Business Machine Corporation.

PS/2 is a registered trademark of IBM Corporation.

All other brand and product names referred to in this manual are trademarks or registered trademarks of their

respective holders.

- 3 -

PREFACE .............................................................................................................. 4

CHAPTER 1 INTRODUCTION....................................................................................... 5

Specification................................................................................................................................ 5

Accessories of HOT-681 ............................................................................................................. 7

CHAPTER 2 HARDWARE CONFIGURATION .................................................................... 8

The PPGA Celeron Processor ...................................................................................................... 8

Jumpers ....................................................................................................................................... 9

CPU Clock Speed Selection - JP5 and JP6 .................................................................................. 9

Clear CMOS - JP9 ..................................................................................................................... 11

Flash EEPROM Vpp - JP11....................................................................................................... 11

Keyboard & PS/2 Mouse Power-on Setting - JP2 ...................................................................... 11

Connectors ................................................................................................................................ 12

CHAPTER 3 MEMORY CONFIGURATION ..................................................................... 15

CHAPTER 4 FLASH UTILITY .................................................................................... 16

CHAPTER 5 AWARD BIOS SETUP .......................................................................... 18

The Main Menu ......................................................................................................................... 19

Standard CMOS Setup............................................................................................................... 21

BIOS Features Setup ................................................................................................................. 23

Chipset Features Setup .............................................................................................................. 26

Power Management Setup ......................................................................................................... 29

PCI Configuration Setup ........................................................................................................... 32

Integrated Peripherals ................................................................................................................ 34

Password Setting ....................................................................................................................... 37

TABLEOF CONTENTS

- 4 -

PPREFACE

HOT-681 is a highly integrated IBM PC/ATX compatible system board designed to

meet the industry's most demanding desktop applications.

Based on the Intel 82440BX AGPset chipset which support up to 500MHz PPGA

Celeron processor with MMX technology.

HOT-681 is equipped with an Accelerated Graphics Port (A.G.P.), a high-performance

interconnect for graphic-intensive application, such as 3D applications. The A.G.P. is

independent of the PCI bus and is designed to exclusively use with graphical-display

devices. The HOT-681 supports 3.3 V A.G.P. devices with data transfer rates up to 133

MHz, allowing data throughput of 500 MB/sec.

The Intel's 82440BX AGPset chipset provides an integrated Bus Mastering IDE control-

ler with two high performance IDE interfaces which allows up to four IDE devices

connection and up to 33 MB/sec of data transfer rates.

The on-board I/O controller provides standard PC I/O functions:

floppy drive interface, two FIFO serial ports, an InDA device port and a SPP/EPP/ECP

capable parallel port.

HOT-681 is built with four PCI local bus slots providing a high bandwidth data path for

data-movement intensive functions such as graphics, and with three ISA slot.

HOT-681 provides the foundation for cost effective, high performance and highly

expandable platforms, which delivers the latest in the Intel PPGA Celeron processor and

new advanced chipset technology.

- 5 -

The HOT-681 Mainboard is carefully designed for the demanding PC user who wants high perfor-

mance and many intelligent features in a compact package:

Intel Chipset:

Features Intel's 440BX AGPset with I/O subsystems.

CPUSupport:

Intel PPGA Celeron processor 300/66, 333/66, 366/66, 400/66 and 350/100, 400/100, 450/100 ,

500/100 MHz.

VersatileMemory Supports:

Supports three banks of normal or PC/100 SDRAM maximum memory size up to 768MB.

Configurable support for ECC (Error Checking and Correcting)

PCIand ISA ExpansionSlots:

Provides four 32-bit PCI slots and three 16-bit ISA slot.

Onboard I/O:

Provides one Floppy port; one PS/2 mouse and one PS/2 Keyboard port connector; two high-speed

UART compatible serial ports and one parallel port with ECP and EPP capabilities. Serial Port 2

can also be directed from COM2 to the Infrared Module for wireless connections.

OnboardPCI Bus Master IDEController:

Two Ultra DMA/33 Bus Master IDE Ports supports four IDE devices up to 33 MB/sec IDE trans-

fers and supports Enhanced PIO Modes 3 and 4 and Bus Master IDE DMA Mode 2 devices.

Onboard20-pin ATX PowerSupply:

Provides ATX power connector onboard supports soft-on/off function.

System BIOS:

Provides licensed Award V4.51PG BIOS on Flash EEPROM.

Supports Green PC, DMI and Bundled with NCR SCSI BIOS.

ACPI:

Support ACPI (Advanced Configuration and Power Interface) function. ACPI provide more

Energy Saving Features for the future operating system supporting OS Direct Power Management

(OSPM) functionality.

INTRODUCTION

- 6 -

Board Size:

ATX form factor 305mm x 170mm.

Advanced Features:

Low EMI -- Spread Spectrum built in - ±0.5% or ±0.3% modulation and automatic clock shut-off

of unused PCI/SDRAMS slots to reduce the EMI.

Dual Function Power Button -- The system can be one of two states, one is Suspend mode and

the other is the Soft-off mode. Pushing the power button for less than 4 seconds will place the

system into Suspend mode. When push the power button for more than 4 seconds, the system

enters the Soft-off mode.

Wake-On-LAN -- The system will power-on automatically by activating of LAN.

(This function support Intel LAN card only).

Modem Ring Power-on -- The system will power-on automatically by activating of modem ring.

PS/2 Keyboard & Mouse Power-on -- The system will power-on automatically by stroke key-

board or double click PS/2 mouse.

Voltages Monitoring -- System voltages levels are monitored to ensure stable current to main

board components.

System voltages include VCORE and VTT for CPU, and +5V, +12V, -5V, -12V for system.

FAN Status Monitoring -- To prevent CPU overheat, CPU fans is monitored for RPM and failure.

(CPU Cooling FAN with RPM sensor is required)

- 7 -

ACCESSORIESOF HOT-681

- 8 -

2HARDWARECONFIGURATION

HOT-681 mainboard provides a 370-pin ZIF Socket370 for Intel PPGA Celeron CPU. The

CPU that came with the mainboard should have a fan attached to it to prevent overheating. If

this is not the case then purchase a fan before you turn on your system.

To install a CPU, first turn off your system and remove its cover. Locate the ZIF Socket370

and open it by first pulling the lever sideways away from the socket then upwards to a 90-

degree right angle. Insert the CPU with the correct orientation as shown.(Figure 2-1) Use

the notched corner of the CPU as your guide. The notched corner should point towards the

end of the lever. Notice that there are two blank area where one hole is missing from that

corner of the square array of pin holes. Because the CPU has a corner pin for two of the four

corner, the CPU will only fit in the one orientationn, hold down on the CPU and close the

socket’s lever.

The Installation PPGA Celeron Processor

Figure 2-1

Figure 2-2

Then you should have a CPU fan that

will cover the face of the CPU. Apply

thermal jelly to the CPU metallic top and

then install the fan onto the CPU. (Figure

2-2 )

- 9 -

Multiplier JP6(66)

MHz

6.5X433

7X466

7.5X500

Jumpers

HOT-681 mainboard features a clock generator to provide adjustable system clock frequency.

JP5 is a 6-pin jumpers which determine the system clock frequency 66 MHz to 133 MHz. and

JP6 is a 8-pin jumper which determine the processor clock ratio from 3.5X to 8X.

Several hardware settings are made through the use of jumper caps to connect jumper pins on

the main board. The jumper's pin 1 on main board will be on the top or on the left when hold-

ing the main board with the keyboard connector away from yourself.

Jumpers with two pins will be shown as for Close (On) and for Open (Off).

To connect the pins, simply place a plastic jumper cap over the two pins.

CPU Clock Speed and ratio Selection - JP5 and JP6

Figure 2-4 shows the position of JP5 and JP6 on the mainboard.

Table 2-1 shows adjustable System clock

on jumper JP5.

Table 2-2, 2-3 and 2-4 shows adjustable

CPU Clock Ratios on jumper group JP6.

SystemClock JP5

66 MHz

75 MHz

83 MHz

100 MHz

103 MHz

112 MHz

133 MHz

Table 2-1

Table 2-2

Multiplier JP6(100)

MHz

3.5X350

4X400

4.5X450

5X500

Table 2-4

Table 2-3

Multiplier JP6(66)

MHz

4.5X300

5X333

5.5X366

6X400

Figure 2-3

- 10 -

CPU Host Clock and Clock Ratios Configuration Table (Table 2-5) shows the PPGA Celeron

processor 300 MHz ~ 500 MHz quick setting on the mainboard.

ProcessorSystemClock

JP5Multiplier

JP6

300 MHz

(66MHzx4.5)

333 MHz

(66MHzx5)

366 MHz

(66MHzx5.5)

400 MHz

(66MHzx6)

350 MHz

(100MHzx3.5)

400 MHz

(100MHzx4)

433 MHz

(66MHzx6.5)

450 MHz

(100MHzx4.5)

466 MHz

(66MHzx7)

500 MHz

(66MHzx7.5)

500 MHz

(100MHzx5)

Special Tip for User's Reference Only

HOT-681 mainboard provides a special JumperJP4

to overspeed your 66 MHz based Intel PPGA Celeron

processor to 100 MHz when jumper group JP6 set to

MANUAL.

Normally, CPU Host Clock 100 ~ 133 MHz are not

available for 66 MHz based processor no matter Soft-

Configure or Hard-Configure.

But, when pull out mini jumper from JP4 (let it open),

the user can Hard-Configure your 66 MHz based

processor to 100 MHz based. For example, overspeed

your 333 MHz (66 MHz x 5) PPGA Celeron to

400 MHz (100 x 4) or more. Figure 2-4

Table 2-5

Inhaltsverzeichnis

Andere Shuttle Hauptplatine Handbücher

Shuttle

Shuttle HOT-679V Bedienungsanleitung

Shuttle

Shuttle AB49 Bedienungsanleitung

Shuttle

Shuttle Spacewalker MV17 Bedienungsanleitung

Shuttle

Shuttle FN25 Bedienungsanleitung

Shuttle

Shuttle FS56 Bedienungsanleitung

Shuttle

Shuttle FB95 Bedienungsanleitung

Shuttle

Shuttle HOT-661/P Bedienungsanleitung

Shuttle

Shuttle Spacewalker AV40 Bedienungsanleitung

Shuttle

Shuttle FS51 Bedienungsanleitung

Shuttle

Shuttle FT20 Bedienungsanleitung

Shuttle

Shuttle Spacewalker MV18 Bedienungsanleitung

Shuttle

Shuttle AN50R Bedienungsanleitung

Shuttle

Shuttle HOT-675V Bedienungsanleitung

Shuttle

Shuttle AB61 Bedienungsanleitung

Shuttle

Shuttle Spacewalker AK31 Bedienungsanleitung

Shuttle

Shuttle FB77 Bedienungsanleitung

Shuttle

Shuttle FV25 Bedienungsanleitung

Shuttle

Shuttle MK35V Bedienungsanleitung

Shuttle

Shuttle FB51 Bedienungsanleitung

Shuttle

Shuttle Spacewalker AE14 Bedienungsanleitung

Shuttle

Shuttle FB61 Bedienungsanleitung

Shuttle

Shuttle AV42 Bedienungsanleitung

Shuttle

Shuttle HOT-675Z Bedienungsanleitung

Shuttle

Shuttle MS52 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung