Siemens QVM62.1 Bedienungsanleitung

Installation Instructions

Document No. 129-095

September 24, 2009

QVM62.1 Air Velocity Sensor

Item Number 129-095, Rev. AA Page 1 of 3

Product Description

This sensor is used to measure the air velocity in a

duct and provide a 0 to 10V signal to a controller

that is proportional to the velocity. This allows the

controller to maintain a constant airflow in the duct,

balance out pressure fluctuations (supply or exhaust

air control), or just monitor the flow in a duct. The Air

Velocity Sensor is generally used for modulating fan

control in primary applications to set the basic

volume flow.

Product Number

QVM62.1

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not follow the

procedures as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools

•Pencil

•Hammer

•Center hole punch

•Screwdrivers

•Four - #8 × 1/2-inch sheet metal screws

•Electric drill with 1/8-inch and 7/8-inch

drill bits

Expected Installation Time

45 minutes

Prerequisites

Field wiring must be pulled to installation location.

Installation

Probe Mounting Flange and Sensor

1. Determine the depth of insertion required for

the probe and assemble the extension tube

and/or probe end cap onto the primary sensor

head tube.

NOTE: If the insertion depth required is less

than or equal to 5.7 inches (145 mm)

the extension tube may be removed by

disconnecting the probe cable at the

transducer head, and sliding the

extension tube off the cable. (With the

extension tube installed, the probe’s

depth of insertion is 11.8 inches

[300mm].) If the extension tube is

removed, be sure to reinstall the

probe’s end cap on the cable before

rewiring it to the transducer head.

2. Position the probe mounting flange on the duct

where will be installed. Lightly tap the screw

heads to create drill marks for the mounting

screw holes.

NOTE: Install the sensor in the ductwork in a

location where the airflow is not

turbulent. Do not place it close to

dampers, registers, or bends in

ductwork.

Figure 1. Mounting Locations.

Document No. 129-095

Installation Instructions

September 24, 2009

Page 2 of 3Siemens Industry, Inc.

3. Draw a line between opposite drill marks,

farthest from each other, and make a drill mark

with the punch, at the intersection of the two

lines.

4. Drill four 1/8-inch holes for the mounting screws

at the points labeled “A”, and a 7/8-inch

diameter hole at the point labeled “B” (see

Figure 2).

Figure 2. Mounting Screw Locations.

5. Secure the flange to the duct using the screws

included with the flange and insert the probe into

the duct. Do not tighten the mounting screw at

this time.

Transducer

1. Remove the cover from the transducer head

unit.

2. Hold the base on the duct or structure to which it

is to be mounted and mark the center positions

of the four mounting holes.

NOTE: Make sure there is enough slack in the

probe’s cable so that, if necessary, the

probe can be removed for servicing or

replacement.

3. Make drill hole marks with the punch at the

mounting hole points, and drill four 1/8-inch

holes.

4. Secure the transducer head to its mounting

location with four #8 × 1/2-inch sheet metal

screws.

5. Set jumper for desired airflow range (see

Figure 3).

6. Connect the Field wiring to the transducer head

connector (see Figure 3.)

1 Terminal block for connection to the

immersion stem

2 Terminal block for connection to controller

3 Plug-in unit for setting the three velocity

ranges. The following applies:

No plug-in jumper = 0 to 5 m/s

Plug-in jumper on 1 and 2 = 0 to 10 m/s

(factory setting)

Plug-in jumper on 2 and 3 = 0 to 15 m/s

Figure 3. Wiring and Setting Elements.

7. Reinstall the cover

CAUTION:

The sensor head connections are not

protected against 24 Vac operating

voltage.

If the unit power supply lead being

connected to terminal G is live during

the installation of the sensor, contact

with any of the sensor head terminals

can irreparably damage the unit.

8. Set the probe’s depth of insertion and position

the arrow on the probe cap so that it points in

the direction of the airflow.

9. Tighten the mounting screw located on the side

of the mounting flange (see Figure 4).

The installation is now complete.

Document No. 129-095

Installation Instructions

September 24, 2009

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

Industry, Inc.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

U.S.A.

Tel. +1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com

Document No. 129-095

Printed in the U.S.A.

Page 3 of 3

Figure 4.

Inhaltsverzeichnis

Andere Siemens Zubehör Handbücher

Siemens

Siemens SENTRON VL Series Bedienungsanleitung

Siemens

Siemens LDS 6 Bedienungsanleitung

Siemens

Siemens Milltronics RBSS Bedienungsanleitung

Siemens

Siemens SITRANS WW100 Bedienungsanleitung

Siemens

Siemens SITRANS WS300 Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens SIWAREX JB Bedienungsanleitung

Siemens

Siemens TC12 Leitfaden

Siemens

Siemens IR270CT Bedienungsanleitung

Siemens

Siemens 5WG1 258-2EB22 Bedienungsanleitung

Siemens

Siemens QFM3100 Service-Handbuch

Siemens

Siemens 5WG1 201-2DBx3 Series Bedienungsanleitung

Siemens

Siemens 3200 Series Bedienungsanleitung

Siemens

Siemens 6DR4004-6NN Series Bedienungsanleitung

Siemens

Siemens SITRANS WW100 Bedienungsanleitung

Siemens

Siemens BS-240 Stücklistenhandbuch

Siemens

Siemens SITRANS WM300 MFA Bedienungsanleitung

Siemens

Siemens SITRANS LG270 Bedienungsanleitung

Siemens

Siemens QAA4292.EWSC Bedienungsanleitung

Siemens

Siemens WEPS Bedienungsanleitung

Siemens

Siemens SIMATIC Vision Sensor VS 130-2 Bedienungsanleitung

Siemens

Siemens QNA2 D Series Leitfaden

Siemens

Siemens Symaro QAA2890/WI Bedienungsanleitung

Siemens

Siemens 3VL9400-4W.30 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung