Siemens MKB-1 Bedienungsanleitung

Installation Instructions

Model MKB-1

Annunciator/Keypad Module

The Model MKB-1 Annunciator from Siemens

Industry, Inc., communicates with the MMB Main

Control Board through the System network link.

The MKB-1 provides the MXL with its primary

control and annunciation.

OPERATION

The MKB-1 has an 80 character, backlit LCD

alphanumeric display that continuously updates

information about the System status and user

defined device messages (See Figure 1). If there

are multiple alarms, security conditions,

supervisories, and/or troubles, the MKB-1

displays the highest priority event that occurred.

The user can see additional event data by

pressing the NEXT key. Press the HOLD key at

any time to stop the display from scrolling.

There are switches for acknowledging fire alarms

(ALARM ACK), silencing audibles (AUD SIL),

acknowledging supervisories (SUPV ACK),

System troubles (TRBL ACK), and security

conditions (SEC ACK). There is also a separate

key for resetting the Control Panel (RESET).

The 10 digit numeric keypad allows entry of the

three levels of user passwords. It also performs

specific menu driven operations as well as

programming and maintenance functions.

Another series of switches located on the MKB-1

allows the user access to the MXL Control menu.

There are also System status indicator LEDs. The

ALARM and TROUBLE LEDs function even if the

main processor fails (See Figure 1).

INSTALLATION

Remove all system power before installation,

first battery and then AC. (To power up,

connect the AC first, then the battery.)

Unpack the MKB-1. Inspect the module for such

things as integrated circuits (ICs) not firmly

seated in their sockets, bent IC pins, connectors

not properly installed, dirt, and packing material

on the board.

Setting the Network Address

(See Figure 2)

1 . Before installing the MKB-1 panel, set the

network address on S1, the switch on the

ANN-1 board located on the back of the

MKB-1. Use dipswitches SW1 and SW2 on

switch Sl to set the network address of the

MKB-1.

2. The MKB-1 module address is always set

within network addresses 248 through 251.

Set the individual switches as follows:

NOTE: Switches S1-SW3 and S1-SW4 are for

future use. The use of switch S1-SW5 is

described below.

HCTIWS

:ROFTESSESSERDDA

842942052152

1WS-1SFFO-nepONO-desolCFFO-nepONO-desolC

2WS-1SFFO-nepOFFO-nepONO-desolCNO-deso

3WS-1SNO-desolCNO-desolCNO-desolCNO-desolC

4WS-1SNO-desolCNO-desolCNO-desolCNO-desolC

5WS-1SNO-desolCNO-desolCNO

-desolCNO-desolC

3. One supervised MKB-1 must be installed at

network address 251. Other supervised

MKBs may be at the other addresses.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-090856-9

To Select Supervision

Use Switch S1-SW5 on the ANN-1 to select or

deselect supervision of the MKB-1. If your ANN-1

has a switch with position 1 indicated on the

lefthand side, ignore the printing on the switch.

SW1 on S1 is at the extreme right-hand side of

S1, regardless of any other marking.

To set for supervision:

S1-SW5 = Closed (ON)

To set for non-supervision:

S1-SW5 = Open (OFF)

This supervision is independent of the network

address.

Mechanical Installation

The installation kit for the MKB-1 includes:

two nuts

two 2 inch standoffs

1 . Mount the MKB-1 inside the main MXL

enclosure by placing the four holes in the

mounting bracket over the four studs provided

in the enclosure. These studs are placed two

above and two below the MMB-1 board (See

Figure 2).

When the MKB-1 is in position, it straddles the

middle of the MMB-1, leaving only the field

wiring terminals on the MMB-1 exposed.

2. Fasten the MKB-1 bracket in the enclosure

using the two 2 inch standoffs provided on top

and the two nuts provided at the bottom.

3. Once the MKB-1 is mounted to the enclosure,

connect the cable assembly on the back of the

MKB-1 to connector P8 on the MMB-1.

Figure 1

MKB-1 Panel Figure 2

Setting S1 on the ANN-1 Board

Figure 3

Placing the MKB-1 Module in the Enclosure

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm57

tnerruCeludoMCDV42evitcAAm0

tnerruCeludoMCDV42ybdnatSAm6

P/N 315-090856-9

Andere Handbücher für MKB-1

Andere Siemens Controller Handbücher

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC S7-200 Benutzerhandbuch

Siemens

Siemens LMV37.4 Series Bedienerhandbuch

Siemens

Siemens Ertec 400 Bedienungsanleitung

Siemens

Siemens OpenAir G..B181.1E/KN Series Installationsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Benutzerhandbuch

Siemens

Siemens SIMATIC Mobile Client900WXN Bedienungsanleitung

Siemens

Siemens SKD62UA Bedienungsanleitung

Siemens

Siemens GD Series Bedienungsanleitung

Siemens

Siemens SSA911.01TH Bedienungsanleitung

Siemens

Siemens 8MR2170 Bedienungsanleitung

Siemens

Siemens SINUMERIK 840D sl Merkblatt

Siemens

Siemens SIMATIC S7 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RM10 Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3RA1.5 Bedienungsanleitung

Siemens

Siemens SIMOTION Series Bedienungsanleitung

Siemens

Siemens 5WG1 523-1AB04 Bedienungsanleitung

Siemens

Siemens instabus JB526C23 Bedienungsanleitung

Siemens

Siemens GIB 1 Series Bedienungsanleitung

Siemens

Siemens BACnet Bedienungsanleitung

Siemens

Siemens SITOP UPS1600 under STEP 7 V12 Bedienungsanleitung

Siemens

Siemens SIMOCODE pro Benutzerhandbuch

Siemens

Siemens OpenAir GBB161.1U Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung