Siemens SIMATIC WinAC Slot 412 Bedienungsanleitung

Important Information, Contents

Product Overview 1

Installing WinAC Slot 41x 2

Getting Started 3

Using the Tool Manager 4

Appendices

Index

06/2000

A5E00065531-03

Windows Automation Center

WinAC Slot 412/WinAC Slot 416

Version 3.1

Overview

This manual is part of the documentation package with order no:

6ES7 673-6CC01-8BA0

SIMATIC

Index-2WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

!Danger

indicates that death, severe personal injury or substantial property damage will result if proper precau-

tions are not taken.

!Warning

indicates that death, severe personal injury or substantial property damage can result if proper precau-

tions are not taken.

!Caution

indicates that minor personal injury or property damage can result if proper precautions are not taken.

Note

draws your attention to particularly important information on the product, handling the product, or to a

particular part of the documentation.

Qualified Personnel

Only qualified personnel should be allowed to install and work on this equipment. Qualified persons

are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment,

and systems in accordance with established safety practices and standards.

Correct Usage

Note the following:

!Warning

This device and its components may only be used for the applications described in the catalog or the

technical descriptions, and only in connection with devices or components from other manufacturers

which have been approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed cor-

rectly, and operated and maintained as recommended.

Trademarks WinAC, SIMATIC, SIMATIC HMIand SIMATIC NETare registered trademarks of SIEMENS AG.

Some of other designations used in these documents are also registered trademarks; the owner’s rights

may be violated if they are used by third parties for their own purposes.

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as well as to

protect the product and connected equipment. These notices are highlighted in the manual by a warning

triangle and are marked as follows according to the level of danger:

We have checked the contents of this manual for agreement with the hard-

ware and software described. Since deviations cannot be precluded entirely,

we cannot guarantee full agreement. However, the data in this manual are

reviewed regularly and any necessary corrections included in subsequent

editions. Suggestions for improvement are welcomed.

The reproduction, transmission or use of this document or its contents is not

permitted without express written authority. Offenders will be liable for

damages. All rights, including rights created by patent grant or registration of

a utility model or design, are reserved.

Siemens AG

Automation and Drives (A&D)

Industrial Automation Systems (AS)

Postfach 4848, D- 90327 Nürnberg SiemensAG 1998-2000

Technical data subject to change.

Siemens AktiengesellschaftA5E00065531

iii

WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

Important Information

Purpose of the manual

The software and hardware components of the Windows Automation Center

(WinAC) allow you the combined solution consisting of data processing, control,

visualization and communications on your PC (PC-based control). The following

versions of the WinAC product are available:

WinAC Slot 412

WinAC Slot 416

This manual will familiarize you with the individual components ofthe WinAC Slot 412

and WinAC Slot 416 product versions by way of an overview.

Important Information

iv WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

Package as supplied

This package has the Order Number 6ES7 673-6CC01-8BA0 and consists of three

manuals and a list of instructions containing the following:

Overview of the Windows Automation Center WinAC Slot 412/WinAC Slot 416

Overview of the components of WinAC

Instructions for installing the software

Getting started

Manual “WinAC Controlling with CPU 412-2 PCI/CPU 416-2 PCI; Set-Up, CPU Data”

Installing and wiring CPUs 41x-2 PCI and the PS extension board

Commissioning CPUs 41x-2 PCI and the PS extension board

Description of control panel, router, time synchronization

Technical specifications

Compatibility with CPU 416-2 DP ISA/CPU 416-2 DP ISA Lite

Manual “SIMATIC Computing”

Function and running of the SIMATIC Computing software

Description of the controls

S7-400 instruction list

Instruction set for all CPUs

Brief description of instructions and execution times

List of OBs, system events, SSL IDs, SFCs/SFBs

Audience

This manual is intended for engineers, programmers, and maintenance personnel

who have a general knowledge of programmable logic controllers.

Scope and usage of the manual

The functions and running of the software for WinAC Slot 41x is described in the

form of an overview. It contains:

overviews of the components contained in the WinAC Slot 41x package

instructions for installing the software for WinAC Slot 41x

Important Information

WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

Applicability

The manual contains information that is valid at the time of the manual being

published. We reserve the right to enclose further information in the form of a

Product Information bulletin.

Additional support

Should you have any questions on using the products described in the manual to

which you cannot find answers in the manual, please get in touch with your contact

at your local Siemens agency or office.

If you have any questions or suggestions concerning this manual, please fill in the

form at the end of this manual and return it to the specified address. Please feel

free to enter your personal assessment of the manual in the form provided.

We offer a range of courses to help get you started with the SIMATIC S7

automation system. Please contact your local training center or the central training

center in Nuremberg, D-90327 Germany (tel. +49 (911) 895-3200).

Constantly updated information

You can obtain up-to-the-minute information on SIMATIC products:

On the Internet at http://www.ad.siemens.de/

By dialing the fax polling number +49-8765-93 00-55 00

In addition, the SIMATIC Customer Support provides up-to-date information and

downloads for users of SIMATIC products:

On the Internet at http://www.ad.siemens.de/simatic-cs

Via the SIMATIC Customer Support mailbox at the following number:

+49 (911) 895-7100

To access the mailbox, use a modem with up to V.34 (28.8 kbps), and set the

parameters as follows: 8, N, 1, ANSI. Alternatively, access it using ISDN

(x.75, 64 kbps).

You can reach SIMATIC Customer Support by telephone at +49 (911) 895-7000

and by fax at +49 (911) 895-7002. Queries can also be addressed to us by Internet

mail or by mail to the mailbox specified above.

Important Information

vi WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

vii

Windows Automation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

Contents

Important Information

1 Product Overview

1.1 What Are WinAC Slot 412 and WinAC Slot 416? 1-2. . . . . . . . . . . . . . . . . . . .

1.2 CPU 41x-2 PCI Is for Controlling Your Process 1-5. . . . . . . . . . . . . . . . . . . . . .

1.3 The PS Extension Board Makes You Independent of a PC 1-6. . . . . . . . . . . .

1.4 Communication Options with CPU 41x-2 PCI 1-7. . . . . . . . . . . . . . . . . . . . . . .

1.5 Router for Communications of CPU 41x-2 PCI 1-9. . . . . . . . . . . . . . . . . . . . . .

1.6 Time Synchronization (PLCTimeSync) 1-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7 SIMATIC Computing Creates Access to Process Data 1-11. . . . . . . . . . . . . . . .

1.8 Tag Files Allow You to Use Symbols for Process Data... 1-12. . . . . . . . . . . . . .

1.9 Tag Files Allow You to Access Multiple Control Engines... 1-13. . . . . . . . . . . . .

1.10 Use SIMATIC Computing across a DCOM Network 1-14. . . . . . . . . . . . . . . . . .

1.11 Using OPC to Connect Third-Party Applications to

SIMATIC Computing 1-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.12 The WinAC Tool Manager Provides Shortcuts to Your Programs 1-16. . . . . . .

2 Installing WinAC Slot 41x

2.1 Overview of the Installation 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Installing and Uninstalling the WinAC Slot 41x Software 2-3. . . . . . . . . . . . . .

3 Getting Started

3.1 The Task: Communications Via the Router 3-2. . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.1 Creating a Project 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.2 Configuring the Access Point 3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.3 Starting the Router 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.4 Communications 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Using the Tool Manager

4.1 Creating a Toolbar for Easy Access to Your Programs 4-2. . . . . . . . . . . . . . . .

4.2 Using the WinAC Tool Manager without a Mouse 4-4. . . . . . . . . . . . . . . . . . . .

4.3 Changing the Language 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A Distributed Component Object Model (DCOM)

A.1 Using DCOM to Expand the Capabilities of WinAC A-2. . . . . . . . . . . . . . . . . . .

A.2 Connecting to a Specific Control Engine Using DCOM A-4. . . . . . . . . . . . . . . .

Contents

viii Windows Automation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

B OLE for Process Control (OPC)

B.1 Using OPC with SIMATIC Computing B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Index

Figures

1-1 Control Panel 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2 Using the CPU 41x-2 PCI in WinAC Slot 41x 1-5. . . . . . . . . . . . . . . . . . . . . . . .

1-3 PS Extension Board 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4 Communication Options with the CPU 41x-2 PCI 1-7. . . . . . . . . . . . . . . . . . . .

1-5 Communication via the Router 1-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6 Clock synchronization 1-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-7 Accessing the Process Data with SIMATIC Computing 1-11. . . . . . . . . . . . . . .

1-8 Using STEP 7 Symbols to Access Data in the Control Engine 1-12. . . . . . . . .

1-9 Using a Tag File to Access Data from Several Control Engines 1-13. . . . . . . .

1-10 Connecting WinAC on Several Computers across a DCOM Network 1-14. . .

1-11 Using OPC to Connect Third-Party Applications to

SIMATIC Computing 1-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-12 WinAC Tool Manager and Shortcut Icon 1-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1 Installing the Components of WinAC Slot 41x 2-2. . . . . . . . . . . . . . . . . . . . . . .

3-1 Communication via the Router 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2 Creating a Project 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3 Selecting a Mounting Rack 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4 Assigning a CP 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5 Configuring the Hardware of the S7-400 Station 3-6. . . . . . . . . . . . . . . . . . . . .

3-6 MPI Connection 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7 Bus Connection 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-8 Creating a Connection 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-9 Connection Properties 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-10 Setting the PG/PC Interface 3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-11 Setting the CP Properties 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1 WinAC Tool Manager 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2 Inserting Icons into the WinAC Tool Manager 4-3. . . . . . . . . . . . . . . . . . . . . . . .

4-3 Changing the Language for WinAC 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A-1 Using WinAC Components with DCOM on a Standalone Computer A-2. . . .

A-2 Using WinAC on Several Computers with DCOM A-3. . . . . . . . . . . . . . . . . . . .

A-3 Connecting to a Specific Control Engine over DCOM A-4. . . . . . . . . . . . . . . . .

B-1 Applications Working with Many OPC Servers B-2. . . . . . . . . . . . . . . . . . . . . . .

B-2 Using the WinAC OPC Server to Access Your Process Data B-2. . . . . . . . . .

Tables

4-1 Keyboard Operations for the WinAC Tool Manager 4-5. . . . . . . . . . . . . . . . . .

1-1

Windows Automation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

Product Overview

Overview

The WinAC Slot 41x package consists of the following components:

the Slot PLC “CPU 412-2 PCI” or “CPU 416-2 PCI”, two CPUs from the range

of products for the S7-400 for PC-based applications.

the optional PS extension board (PS: power supply; power supply module) for

PC-independent power supply.

the control panel that displays the controls of the CPU 41x-2 PCI on a screen.

the router for the communications of the CPU 41x-2 PCI via a

SIMATIC NET CP (Industrial Ethernet or PROFIBUS) or a network card.

the time synchronization for synchronization of the CPU 41x-2 PCI via a

SIMATIC NET CP (Industrial Ethernet or PROFIBUS).

the SIMATIC Computing software. The SIMATIC Computing software provides

ActiveX controls, which you can use specifically to visualize your process. In

SIMATIC Computing, you can use third-party ActiveX controls in addition to S7

Controls to monitor and modify process data.

Furthermore, SIMATIC Computing has an OPC server (OPC = OLE for

Process Control) which other OPC applications use to access the data in the

controlled device.

WinAC Tool Manager for working with your applications. It is a toolbar that lets

you arrange all the applications you want to use while working with your

process data.

Product Overview

1-2 WindowsAutomation Center WinAC Slot 412/WinAC Slot 416 Version 3.1

A5E00065531-03

In this chapter

Section Contents Page

1.1 What Are WinAC Slot 412 and WinAC Slot 416? 1-2

1.2 CPU 41x-2 PCI Is for Controlling Your Process 1-5

1.3 The PS Extension Board Makes You Independent of a PC 1-6

1.4 Communication Options with CPU 41x-2 PCI 1-7

1.5 Router for Communications of CPU 41x-2 PCI 1-9

1.6 Time Synchronization (PLCTimeSync) 1-10

1.7 SIMATIC Computing Creates Access to Process Data 1-11

1.8 Tag Files Allow You To Use Symbols for Process Data 1-12

1.9 Tag Files Allow You to Access Multiple Control Engines... 1-13

1.10 Use SIMATIC Computing across a DCOM Network 1-14

1.11 Using OPC to Connect Third-Party Applications to SIMATIC

Computing 1-15

1.12 Tool Manager Provides Shortcuts to Your Programs 1-16

1.1 What Are WinAC Slot 412 and WinAC Slot 416?

PC-based control with WinAC Slot 412/WinAC Slot 416

In the top range of the PLC applications, the number of PC tasks such as data

processing and visualization is increasing. The use of PC-based control (= use of a

PC with an integrated PLC) is then frequently the solution to be preferred

compared to the use of a standard PLC with a PC link for communications.

PC-based control is the combination of a PLC and data processing on a PC with

WinAC Slot 412/WinAC Slot 416.

WinAC Slot 412/WinAC Slot 416 combines the automation tasks of open-loop and

closed-loop control, data processing, communications and visualization on a PC.

WinAC Slot 412/WinAC Slot 416 is based on the original Windows NT and uses

standard interfaces for integration into the Office world. WinAC stands for

Windows Automation Center.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Controller Handbücher

Siemens

Siemens LCM-OAVS 570-804PA Bedienungsanleitung

Siemens

Siemens SQL321B Series Bedienungsanleitung

Siemens

Siemens ACM-1 Bedienungsanleitung

Siemens

Siemens S7 Series Gebrauchs- und Pflegehandbuch

Siemens

Siemens RVD110 Bedienerhandbuch

Siemens

Siemens RMZ791 Bedienungsanleitung

Siemens

Siemens OpenAir GCA Series Betriebsanleitung

Siemens

Siemens 3VA9677-0EK11 Bedienungsanleitung

Siemens

Siemens RVL481 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SITRANS LUT400 Bedienungsanleitung

Siemens

Siemens RWD62U Betriebsanleitung

Siemens

Siemens ACVATIX SAX319.03 Bedienungsanleitung

Siemens

Siemens Simatic S7-300 Bedienungsanleitung

Siemens

Siemens Desigo RXC32.1 Bedienungsanleitung

Siemens

Siemens N 501 Service-Handbuch

Siemens

Siemens SFP21/18 Bedienungsanleitung

Siemens

Siemens Simatic S7-200 CPU 210 Benutzerhandbuch

Siemens

Siemens PS 307 6ES7307-1BA01-0AA0 Bedienungsanleitung

Siemens

Siemens ACVATIX G B111.9E/KN Series Bedienungsanleitung

Siemens

Siemens SIMATIC S7 Betriebsanleitung

Siemens

Siemens 3RE10 Series Bedienungsanleitung

Siemens

Siemens Climatix POL822 Bedienungsanleitung

Siemens

Siemens SIMOTION D410 Kurzanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung