Siemens CAB1-X Bedienungsanleitung

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-4

System Enclosure for NCCNT WAN

Installation Instructions

Model CAB1-X

INTRODUCTION The Model CAB1-X enclosure from Siemens Industry, Inc., is used to house system

modules.The CAB1-X backbox and doors are black. The CAB1-X consists of an outer

door, an OD-GP vented grill plate, a mounting plate (CAB-MP), and a backbox as

shown in Figure 1.

BACKBOX

OUTER DOOR

MOUNTING PLATE

OD-GP GRILL PLATE

The backbox is mounted on a flat surface with four user-supplied bolts that are a

maximum of 3/8inch in diameter.

The backbox contains enough space to mount a set of BTX-1 (31 AH) batteries in the

bottom.

PRE-INSTALLATION (Optional) Remove the CAB-MP mounting plate from the backbox.

Figure 1

CAB1-X Enclosure

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-42

INSTALLATION Prior to installation consider the following:

• Mounting height for access to the opening of the outer door.

• Weight and size of the enclosure.

• Local codes.

Install the backbox: 1. Select a clean, dry, shock and vibration free surface.

2. Position the backbox clear of obstructions so that the front door opens freely

and the controls and indicators are easily accessible.

3. Mark the locations of the two upper mounting bolts of the backbox on the

wall. (Refer to Figure 2.)

4. Drill the two holes located in the previous step and screw in the top bolts,

leaving a small gap between the wall and each top bolt.

5. Place the backbox over the two top bolts and allow it to slide down over the

bolts. (Refer to Figure 3.)

6. Mark, drill, and install the two bottom bolts in the backbox.

7. Tighten all four bolts securely against the back wall of the backbox.

MOUNTING

HOLES FOR

CAB1-X

21.25

27.00

18.00

26.12

Figure 2

CAB1-X Mounting Holes

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-43

MOUNTING BOLTS

4 PLACES

(USER SUPPLIED)

WIRING In compliance with NEC Article 760, all power limited fire protective signaling conduc-

tors must be separated a minimum of ¼ inch from all of the following wiring located

within a control panel:

• electric light

•power

• Class 1 or non-power limited fire protective signaling conductors

To meet these requirements, the following guidelines must be observed when

installing modules and wiring to this control panel.

When installing power limited field wiring, the installer must comply with NEC article

760, which states:

The fire alarm power-limited circuits are installed using Types FPL, FPLR, FPLP or

permitted substitute cable, provided these power-limited cable conductors extending

beyond the jacket are separated by a minimum of 0.25 in. (6.35 mm) or by a noncon-

ductive sleeve or nonconductive barrier from all other conductors.

If energy limited cable or equivalent is not used within the CAB1-X enclosure, then

the following guidelines do not apply. In that case, be sure to follow standard wiring

practices.

Wiring Entering Enclosure Non-Power Limited Wiring

Wiring entering the enclosure from the bottom and right side of the backbox is

considered non-power limited wiring. Wiring must be in the shortest route and must

not overlap any other wiring.

Figure 3

Mounting The CAB1-X

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-44

Power Limited Wiring

Wiring entering the enclosure from the top and the left side of the backbox is consid-

ered power limited. Wiring must be in the shortest route and must not overlap any

other wiring.

Use the existing lances in the backbox to dress the wires as needed to maintain

separation of power limited and non-power limited wiring.

Install Wiring The System is designed to operate from an external 120 VAC, 60 Hz power source.

The primary mains input must have a separate or dedicated circuit breaker. Wire in

accordance with local codes and NEC 760.

1. Remove the knockouts in the backbox for the entry of field wiring. (Refer to

Figure 4 for the location of knockouts.)

2. Pull all field wiring into the backbox. Do not dress the wiring until the

location of all the equipment is known.

3. Install the wiring from the external power source to the approximate location

of the power supply.

POST-INSTALLATION After the backbox is installed and the wiring completed, finish the installation by

installing the mounting plate, the outer door, the OD-GP grill plate, and the ground

straps.

1. Install the mounting plate if removed.

2. Install the door by placing it on its hinges. (Refer to Figure 5, page 5.)

3. Install the OD-GP vented grill plate on the door and secure with the 10-32

nuts supplied. (Refer to Figure 6, page 5.)

4. Install the ground strap on the door. (Refer to Figure 7, page 6.)

SPECIFICATIONS CAB1-X backbox:

26-1/8”W x 6-7/8”D x 27”H

KNOCKOUTS

(16 PLACES)

Figure 4

CAB1-X Knockouts

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-45

Figure 5

Installing The Door On The CAB1-X

DOOR

HINGE

CAB1-X DOOR

OD-GP GRILL PLATE

Figure 6

Installing The OD-GP Grill Plate OnThe CAB1-X Door

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-46

GROUND STRAP

ON DOOR

Figure 7

Ground Strap Installation

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034369-47

This page has been left intentionally blank.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-034369-4

This page has been left intentionally blank.

Inhaltsverzeichnis

Andere Siemens Gehäuse Handbücher

Siemens

Siemens SINAMICS G120P Bedienungsanleitung

Siemens

Siemens Simatic 6DL2804-0 Series Bedienungsanleitung

Siemens

Siemens SENTRON VL 3VL93008BD00 Bedienungsanleitung

Siemens

Siemens Milltronics HydroRanger 200 Bedienungsanleitung

Siemens

Siemens 549-521 Bedienungsanleitung

Siemens

Siemens BZLLRHSE Bedienungsanleitung

Siemens

Siemens EB-32 Bedienungsanleitung

Siemens

Siemens FS-250-ENCL/-R Bedienungsanleitung

Siemens

Siemens 8MF4900 Bedienungsanleitung

Siemens

Siemens TH 180 AP Bedienungsanleitung

Siemens

Siemens CAB2-BD/-RD Bedienungsanleitung

Siemens

Siemens FDMH292-R Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU180-N Series Bedienungsanleitung

Siemens

Siemens CERBERUS PYROTRONICS ALI-8 Bedienungsanleitung

Siemens

Siemens FHD2012-U1 Bedienungsanleitung

Siemens

Siemens MTE-2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3SB380D Series Bedienungsanleitung

Siemens

Siemens BB-55 Bedienungsanleitung

Siemens

Siemens FHA2040-A1 Bedienungsanleitung

Siemens

Siemens 7KE6020-1AA00 Bedienungsanleitung

Siemens

Siemens EAD-3 Bedienungsanleitung

Siemens

Siemens MLE-6 Bedienungsanleitung

Siemens

Siemens H200 Bedienungsanleitung

Siemens

Siemens 8MF2000 Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung