Siemens Milltronics HydroRanger 200 Bedienungsanleitung

HEATED ENCLOSURE

Instruction Manual April 2002

HEATED ENCLOSURE

Safety Guidelines

Warning notices must be observed to ensure personal safety as well as that of others, and to

protect the product and the connected equipment. These warning notices are accompanied

by a clarification of the level of caution to be observed.

Qualified Personnel

This device/system may only be set up and operated in conjunction with this manual.

Qualified personnel are only authorized to install and operate this equipment in accordance

with established safety practices and standards.

Warning: This product can only function properly and safely if it is correctly transported,

stored, installed, set up, operated, and maintained.

Note: Always use product in accordance with specifications.

Instruments Inc.2002.AllRights ReservedDisclaimer of Liability

This document is available in bound version and in

electronic version. We encourage users to

purchase authorized bound manuals, or to view

electronic versions as designed and authored by

Siemens Milltronics Process Instruments Inc.

Siemens Milltronics Process Instruments Inc. will

not be responsible for the contents of partial or

whole reproductions of either bound or electronic

versions.

While we have verified the contents of

this manual for agreement with the

instrumentation described, variations

remain possible. Thus we cannot

guarantee full agreement. The

contents of this manual are regularly

reviewed and corrections are included

in subsequent editions. We welcome

all suggestions for improvement.

Technical data subject to change.

MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments Inc.

Contact SMPI Technical Publications at the following address:

Technical Publications

Siemens Milltronics Process Instruments Inc.

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario, Canada, K9J 7B1

Email: techpubs@milltronics.com

For the library of SMPI instruction manuals, visit our Web site: www.milltronics.com

7ML1998IFY01 Heated Enclosure– INSTRUCTION MANUAL Page 1

mmmmm

Introduction

Heated Enclosure

This manual provides you with the information required to install and operate your

equipment safely and efficiently.

We always welcome suggestions and comments about manual content, design, and

accessibility. Please direct your emails to tec[email protected]om.

For more information about Siemens Milltronics level measurement instruments and

products, go to our web site: www.siemens-milltronics.com.

Manual Symbols

Please familiarize yourself with the following symbols and how they are used in the

manual.

Introduction

The Siemens Milltronics Heated Enclosure is suitable for almost all indoor/outdoor

applications. Designed to resist wet and dirty conditions, it is particularly effective for

condensation control.

The impact resistant enclosure eliminates dents, weathers well, and is highly resistant to

corrosives, acids, alkalines, and salts.

Enclosure Features

•hingecaps

• nonmetallic molded-in hinges

• rounded corners

• non-conductive – eliminates electrical shock risk

• sufficient interior space for wiring

• fully gasketted

• vertical and horizontal orientation

•clearcover

Notes:

• Please read all sections before installing the Heated Enclosure.

• The Heated Enclosure is to be used only in the manner outlined in this

instruction manual or protection by the equipment may be impaired.

• Information in this manual applies to Heated Enclosure operation only. Please

refer to level instrument documentation for operation information.

alternating current

protective conductor terminal

warning (refer to instructions)

Heater Box.fm Page 1 Wednesday, April 24, 2002 9:47 AM

Page 2 Heated Enclosure – INSTRUCTION MANUAL 7ML1998IFY01

mmmmm

Specifications

Power

• 115 Vac, 50/60Hz, 120 VA

Environmental

• indoor/outdoor

• altitude: 2000m max.

• ambient: – 40°to 50°C (–38°to 122°F)

• relative humidity: suitable for outdoors (Type 4X/NEMA 4X enclosure)

• installation category: II

• pollution degree: 4

• corrosion resistant

Thermostat

• opens at 14° C (57 ° F)

•closes at 7°C (45 °F)

Vertical Enclosure Dimensions

• W. 420 mm (16.5")

• H: 370 mm (14.5")

• D: 215 mm (8.46")

Horizontal Enclosure Dimensions

• W: 370 mm (14.5")

• H: 420 mm (16.5")

• D: 215 mm (8.46")

Important:

• All specifications are subject to change without notice. Please ensure that any

safety related information is confirmed with a qualified Siemens Milltronics

representative.

• Approval information applies to Heated Enclosure only. Please refer to level

instrument documentation for approvals information.

Note: Thermostat open and closed temperatures have a variability factor

of +/– 5° (C/F)

Heater Box.fm Page 2 Wednesday, April 24, 2002 9:47 AM

7ML19981CL01.2 IQ Radar 300 – INSTRUCTION MANUAL Page 3

mmmmm

Specifications

Enclosure Cover

• clear, poly carbonate

Approvals

• NEMA 1, 3, 3S, 4, 4X, 12, 13

• Listed per UL 50 enclosures for electrical equipment

•CSAcertified

• JIC compliant

Heater Box.fm Page 3 Wednesday, April 24, 2002 9:47 AM

Page 4 Heated Enclosure – INSTRUCTION MANUAL 7ML1998IFY01

mmmmm

Installation

Mounting

Mounting Locations

Recommended

• Mount enclosure at shoulder level, unless most interaction of the enclosed

instrument is through a SCADA system

• Ensure easy access for instrument hand programmer is provided

• Mounting surface is free from vibration

Avoid

• Proximity to high voltage/current runs, contacts, SCR or variable frequency motor

speed controllers

Mounting Instructions

Mount the unit where there is sufficient room to swing lid open and have clear access to

contents.

Maintenance

The Heated Enclosure requires no internal cleaning. For external cleaning, wipe with

damp cloth.

Notes:

• Installation must only be performed by qualified personnel, and in accordance

with local governing regulations.

• This product is susceptible to electrostatic shock. Follow proper grounding

procedures.

• The non-metallic enclosure does not provide grounding between conduit

connections. Use grounding type bushings and jumpers.

• Installation information applies to Heated Enclosure only. Please refer to level

instrument documentation for installation guidelines.

All field wiring must have insulation suitable for at least 250 V.

Heater Box.fm Page 4 Wednesday, April 24, 2002 9:47 AM

7ML1998IFY01 Heated Enclosure – INSTRUCTION MANUAL Page 5

mmmmm

Installation

Vertical Mounting

Horizontal Mounting

Orientation changes, but enclosure dimensions are identical to vertical mount.

Note: For ease of use, mount with hinges at bottom so lid hangs open when

unlatched.

305mm

(12.00")

420mm

(16.50")

480mm

(19.00")

7.9mm DIA.

(0.312")

(TYP. 4 PLACES)

370mm

(14.50")

215mm

(8.46")

Heater Box.fm Page 5 Wednesday, April 24, 2002 9:47 AM

Page 6 Heated Enclosure – INSTRUCTION MANUAL 7ML1998IFY01

mmmmm

Wiring

Conduit Entry

Conduit entry is required for Heated Enclosure power supply, level monitor power supply,

and for transducer and communications wiring.

1. Drill the required entry holes. Make sure holes do not interfere with Heated Enclo-

sure operation.

2. Attach conduit using only approved suitable sized hubs for watertight operation.

Vertical Mounting

Horizontal Mounting

Important: Select conduit hole locations carefully. Place them where

the wiring will not interfere with Heated Enclosure operations.

Notes:

• Use conduit hubs certified/approved as Type 4X

• Non-metallic enclosure does not provide grounding between conduit

connections. Use grounding type bushings and jumper wires.

hinges

Recommended Conduit Locations

hinges

Recommended Conduit Locations

Heater Box.fm Page 6 Wednesday, April 24, 2002 9:47 AM

7ML19981FY01 Heated Enclosure – INSTRUCTION MANUAL Page 7

mmmmm

Wiring

Vertical Mount

Warning: Hazardous voltage present on terminal during

operation.

Notes:

• Recommended torque on terminal clamping screws: 0.56 – 0.79 Nm (5–7 in/lbs)

• The equipment must be protected by a 15 A fuse, or a circuit breaker in the

building installation.

• A circuit breaker or switch in the building installation, marked as the disconnect

switch, must be in close proximity to the equipment and within easy reach of

the operator.

• Do not connect level monitor to enclosure terminals.

Important: All safety and operating information in this manual apply to

the Heated Enclosure only. Consult instrument manual for

safety and operating instructions.

COVER NOT SHOWN

115Vac, 120VA

L2/N

thermostat

Milltronics

Level

Monitor

strip heater

terminal block

ground lug terminal

enclosure

level monitor cable entry:

refer to individual product

for power consumption.

Note: do not wire

level monitor to

Heated Enclosure

terminal.

Heater Box.fm Page 7 Wednesday, April 24, 2002 9:47 AM

Page 8 Heated Enclosure – INSTRUCTION MANUAL 7ML1998IFY01

mmmmm

Wiring

Horizontal Mount

L2/N

115Vac, 120VA

enclosure

ground lug terminal

terminal block

strip heater

thermostat

Milltronics

Level

Monitor

level monitor cable entry: refer to individual

productfor power consumption.

Note: do not wire

level monitor to

Heated Enclosure

terminal.

Heater Box.fm Page 8 Wednesday, April 24, 2002 9:47 AM

Inhaltsverzeichnis

Andere Siemens Gehäuse Handbücher

Siemens

Siemens FHA2040-A1 Bedienungsanleitung

Siemens

Siemens 8MF4900 Bedienungsanleitung

Siemens

Siemens SENTRON VL 3VL93008BD00 Bedienungsanleitung

Siemens

Siemens FDMH292-R Bedienungsanleitung

Siemens

Siemens MLE-6 Bedienungsanleitung

Siemens

Siemens FS-250-ENCL/-R Bedienungsanleitung

Siemens

Siemens FHD2012-U1 Bedienungsanleitung

Siemens

Siemens BZLLRHSE Bedienungsanleitung

Siemens

Siemens 8MF2000 Bedienungsanleitung

Siemens

Siemens EB-32 Bedienungsanleitung

Siemens

Siemens BB-55 Bedienungsanleitung

Siemens

Siemens MTE-2 Bedienungsanleitung

Siemens

Siemens CERBERUS PYROTRONICS ALI-8 Bedienungsanleitung

Siemens

Siemens Simatic 6DL2804-0 Series Bedienungsanleitung

Siemens

Siemens TH 180 AP Bedienungsanleitung

Siemens

Siemens SIRIUS ACT 3SU180-N Series Bedienungsanleitung

Siemens

Siemens 7KE6020-1AA00 Bedienungsanleitung

Siemens

Siemens SIRIUS 3SB380D Series Bedienungsanleitung

Siemens

Siemens CAB1-X Bedienungsanleitung

Siemens

Siemens EAD-3 Bedienungsanleitung

Siemens

Siemens SINAMICS G120P Bedienungsanleitung

Siemens

Siemens CAB2-BD/-RD Bedienungsanleitung

Siemens

Siemens 549-521 Bedienungsanleitung

Siemens

Siemens H200 Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung