Siemens SIMATIC ET 200S Bedienungsanleitung
SIMATIC ET 200S distributed I/O Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
_
_____________
_
_____________
Preface
Properties
1
Diagnostics
2
SIMATIC
ET 200S distributed I/O
Digital electronic module
8DI DC24V
(6ES7131-4BF00-0AA0)
Manual
04/2007
A5E01077339-01
Safety Guidelines
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY
Ordernumber: A5E01077339-01
Ⓟ 12/2007
Copyright © Siemens AG 2007.
Technical data subject to change
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Manual, 04/2007, A5E01077339-01 3
Preface
Preface
Purpose of the manual
This manual supplements the
ET 200S Distributed I/O System
Operating Instructions.
General functions for the ET 200S are described in the
ET 200S Distributed I/O System
Operating Instructions.
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Basic knowledge requirements
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of the manual
This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
Recycling and disposal
Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable.
For environmentally compliant recycling and disposal of your electronic waste, please
contact a company certified for the disposal of electronic waste.
Additional support
If you have any questions relating to the products described in these operating instructions,
and do not find the answers in this document, please contact your local Siemens
representative.
http://www.siemens.com/automation/partner
The portal to our technical documentation for the various SIMATIC products and systems is
available at:
http://www.siemens.com/automation/simatic/portal
The online catalog and ordering system are available at:
http://www.siemens.com/automation/mall
Preface
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
4 Manual, 04/2007, A5E01077339-01
Training center
We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in
D -90327, Nuremberg, Germany.
Phone: +49 (911) 895-3200.
http://www.siemens.com/sitrain
Technical Support
You can reach technical support for all A&D projects
● using the support request web form:
http://www.siemens.com/automation/support-request
● Phone: + 49 180 5050 222
● Fax: + 49 180 5050 223
For more information about our technical support, refer to our Web site at
http://www.siemens.de/automation/service
Service & Support on the Internet
In addition to our documentation services, you can also make use of our comprehensive
online knowledge base on the Internet.
http://www.siemens.com/automation/service&support
There you will find:
● Our Newsletter, which constantly provides you with the latest information about your
products.
● The right documentation for you using our Service & Support search engine.
● The bulletin board, a worldwide knowledge exchange for users and experts.
● Your local contact for Automation & Drives in our contact database.
● Information about on-site services, repairs, spare parts. Lots more can be found on our
"Services" pages.
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Manual, 04/2007, A5E01077339-01 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Properties .................................................................................................................................................. 7
1.1 Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0) ....................................................7
2 Diagnostics.............................................................................................................................................. 13
2.1 Diagnostics using LED display.....................................................................................................13
Index........................................................................................................................................................ 15
Table of contents
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
6 Manual, 04/2007, A5E01077339-01
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Manual, 04/2007, A5E01077339-01 7
Properties 1
1.1 Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Properties
● Digital electronic module with eight inputs
● Nominal input voltage 24 VDC
● Suitable for connecting 2-wire sensors
● Supports isochronous operation
Requirements for operation
It is possible to operate the 8DI DC24V digital electronic module using the following interface
modules with the order numbers specified (or higher). The interface modules listed in the
table are not subject to any constraints.
Interface module Order number (or higher) Firmware version
(or higher)
IM 151-1 STANDARD 6ES7151-1AA03-0AB0 ---
IM 151-1 FO STANDARD 6ES7151-1AB02-0AB0 ---
IM 151-1 HIGH FEATURE 6ES7151-1BA01-0AB0 V2.1.3
IM 151-3 PN
IM 151-3 PN HIGH FEATURE
IM 151-3 PN FO
6ES7151-3AA20-0AB0
6ES7151-3BA20-0AB0
6ES7151-3BB21-0AB0
V4.0.1
General terminal assignment
Note
Terminals A4, A8, A3 and A7 are only available at specified terminal modules.
Properties
1.1 Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
8 Manual, 04/2007, A5E01077339-01
Terminal assignment for 8DI DC24V (6ES7131-4BF00-0AA0)
Terminal Assignment Terminal Assignment Notes
1 DI
0 5 DI
1
2 DI
2 6 DI
3
3 DI
4 7 DI
5
4 DI
6 8 DI
7
A4 AUX1 A8 AUX1
A3 AUX1 A7 AUX1
•DIn: Input signal, Channel n
•AUX1: Sensor power supply 24 VDC (for example from power
module) or potential bus (can be used freely up to 230 VAC)
Usable terminal modules
Usable terminal modules for 8DI DC24V (6ES7131-4BF00-0AA0)
TM-E15C26-A1
(6ES7193-4CA50-0AA0)
TM-E15C24-01
(6ES7193-4CB30-0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-0AA0)
TM-E15S24-01
(6ES7193-4CB20-0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-0AA0)
TM-E15N24-01
(6ES7193-4CB70-0AA0)
Fast Connect
$
$8;
$
$
$
',
',
'&9$8;
',
',
/HLWHU
$QVFKOXVVEHLVSLHOH
Properties
1.1 Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Manual, 04/2007, A5E01077339-01 9
Two-wire connection
The following configuration example shows a two-wire connection with the electronic
modules 8DI DC24V. You require further terminals so that sufficient terminals are available
for the 24 VDC sensor power supply when the TM-E15S26-A1 terminal modules are used. In
the example this is implement by the add-on terminal TE-U120S4x10. Per add-on terminal,
terminal modules of the same height must exist across a minimum width of 120 mm. You
can naturally also use other terminals for this configuration (for example, ET 200S potential
distribution module 4POTDIS).
$8;
3
4
2
1
5
6
$$
$$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
'&9
① Terminal module TM-P15S23-A0
② Power module PM-E 24 VDC
③ Electronic modules 8DI DC24V
④ Terminal modules TM-E15S26-A1
⑤ Sensor in 2-wire connection
⑥ Add-on terminal TE-U120S4x10
Properties
1.1 Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
Digital electronic module 8DI DC24V (6ES7131-4BF00-0AA0)
10 Manual, 04/2007, A5E01077339-01
Block diagram
0
3
3
,QSXW
HOHFWURQLFV
,QSXW
HOHFWURQLFV
(7b6
%DFNSODQH
EXV
LQWHUIDFH
%DFNSODQHEXV
Figure 1-1 Block diagram of the 8DI DC24V
Technical Specifications 8DI DC24V (6ES7131-4BF00-0AA0)
Dimensions and weight
Width (mm) 15
Weight Approx. 35 g
Module-specific data
Supports isochronous operation Yes
Number of inputs 8
Length of cable
•Unshielded max. 600 m
•Shielded Max. 1,000 m
Parameter length 3 bytes
Address space 1 byte
Andere Handbücher für SIMATIC ET 200S
33
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Siemens E/A-System Handbücher
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC S5 CP 523 Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens Simatic S7-1500 Stücklistenhandbuch
Siemens
Siemens MICROMASTER 440 GX Technische Daten
Siemens
Siemens BANY Agent Administratorhandbuch
Siemens
Siemens SIMATIC ET 200S Bedienungsanleitung
Siemens
Siemens Simatic S7-1500 Bedienungsanleitung
Siemens
Siemens Simatic S7-1500 Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC S7 EIP-200S Benutzerhandbuch
Siemens
Siemens Simatic S7-1500 Technisches Dokument
Siemens
Siemens SIMATIC ET 200S Bedienungsanleitung
Siemens
Siemens 6DL2804 Series Montageanleitung
Siemens
Siemens SIM-16 Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP HA Technisches Dokument
Siemens
Siemens TX-I/O Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
