Siemens Simatic S7-1500 Bedienungsanleitung

Manual

Analog input module AI 8xU/I HS (6ES7531-7NF10-0AB0)

07/2014Edition

Answers for industry.

SIMATIC

S7-1500

Analog Input Module AI 8xU/I HS

(6ES7531-7NF10-0AB0)

___________________

SIMATIC

S7-1500/ET 200MP

Analog Input Module AI 8xU/I HS

(6ES7531-7NF10-0AB0)

Manual

07/2014

A5E03484886

-AC

Preface

Documentation guide

Product overview

Wiring

Parameters/address space

Interrupts/diagnostics alarms

Technical specifications

Dimensional drawing

Parameter data records

Representation of analog

values

Open Source Software

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E03484886-AC

Ⓟ

07/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

Manual, 07/2014, A5E03484886-AC 3

Preface

Purpose of the documentation

This manual supplements the system manuals:

●S7-1500 Automation System

●ET 200MP Distributed I/O System

Functions that relate in general to the systems are described in these system manuals.

The information provided in this manual and in the system/function manuals supports you in

commissioning the systems.

Changes compared to previous version

Changes described in this manual, compared to the previous version:

●Module integrated in hardware catalog STEP 7 (TIA Portal) V13, Update 3 or higher with

the functions:

–Module-internal shared input (MSI) for Shared Device

–Configurable submodules, e.g., for Shared Device

●Appendix Open Source Software amended

Conventions

The term "CPU" is used in this manual both for the CPUs of the S7-1500 automation system,

as well as for interface modules of the ET 200MP distributed I/O system.

Please also observe notes marked as follows:

Note

A note contains important information regarding the product described in the documentation

or its handling, or draws special attention to a

section of the documentation.

Preface

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

4Manual, 07/2014, A5E03484886-AC

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, solutions, machines, equipment and/or networks. They are

important components in a holistic industrial security concept. With this in mind, Siemens’

products and solutions undergo continuous development. Siemens recommends strongly

that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable

preventive action (e.g. cell protection concept) and integrate each component into a holistic,

state-of-the-art industrial security concept. Third-party products that may be in use should

also be considered. You can find more information about industrial security on the Internet

(http://www.siemens.com/industrialsecurity).

To stay informed about product updates as they occur, sign up for a product-specific

newsletter. You can find more information on the Internet

(http://support.automation.siemens.com).

Open Source Software

Open-source software is used in the firmware of the product described. Open Source

Software is provided free of charge. We are liable for the product described, including the

open-source software contained in it, pursuant to the conditions applicable to the product.

Siemens accepts no liability for the use of the open source software over and above the

intended program sequence, or for any faults caused by modifications to the software.

For legal reasons, we are obliged to publish the original text of the license conditions and

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

Manual, 07/2014, A5E03484886-AC 5

Table of contents

Preface ................................................................................................................................................... 3

1 Documentation guide .............................................................................................................................. 6

2 Product overview .................................................................................................................................... 8

2.1 Properties..................................................................................................................................8

3 Wiring ................................................................................................................................................... 11

4 Parameters/address space ................................................................................................................... 16

4.1 Measuring types and ranges ..................................................................................................16

4.2 Parameters .............................................................................................................................17

4.3 Declaration of parameters ......................................................................................................18

4.4 Address space ........................................................................................................................20

5 Interrupts/diagnostics alarms................................................................................................................. 26

5.1 Status and error displays ........................................................................................................26

5.2 Interrupts.................................................................................................................................29

5.3 Diagnostics alarms..................................................................................................................31

6 Technical specifications ........................................................................................................................ 32

A Dimensional drawing............................................................................................................................. 36

B Parameter data records......................................................................................................................... 38

B.1 Parameter assignment and structure of the parameter data records.....................................38

C Representation of analog values ........................................................................................................... 44

C.1 Representation of input ranges...............................................................................................45

C.2 Representation of analog values in voltage measuring ranges..............................................46

C.3 Representation of analog values in the current measuring ranges ........................................47

C.4 Measured values for wire break diagnostic ............................................................................48

D Open Source Software.......................................................................................................................... 49

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

6Manual, 07/2014, A5E03484886-AC

Documentation guide

The documentation for the SIMATIC S7-1500 automation system and the SIMATIC

ET 200MP distributed I/O system is arranged into three areas.

This arrangement enables you to access the specific content you require.

Basic information

System Manual and Getting Started describe in detail the configuration, installation, wiring

and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7 online

help supports you in the configuration and programming.

Device information

Manuals contain a compact description of the module-specific information, such as

properties, terminal diagrams, characteristics, technical specifications.

General information

The function manuals contain detailed descriptions on general topics regarding the SIMATIC

S7-1500 and ET 200MP systems, e.g. diagnostics, communication, Motion Control, Web

server.

You can download the documentation free of charge from the Internet

(http://www.automation.siemens.com/mcms/industrial-automation-systems-

simatic/en/manual-overview/tech-doc-controllers/Pages/Default.aspx).

Changes and supplements to the manuals are documented in a Product Information.

Documentation guide

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

Manual, 07/2014, A5E03484886-AC 7

Manual Collection S7-1500 / ET 200MP

The Manual Collection contains the complete documentation on the SIMATIC S7-1500

automation system and the ET 200MP distributed I/O system gathered together in one file.

You can find the Manual Collection on the Internet

(http://support.automation.siemens.com/WW/view/en/86140384).

My Documentation Manager

The My Documentation Manager is used to combine entire manuals or only parts of these to

your own manual.

You can export the manual as PDF file or in a format that can be edited later.

You can find the My Documentation Manager on the Internet

(http://support.automation.siemens.com/WW/view/en/38715968).

Applications & Tools

Applications & Tools supports you with various tools and examples for solving your

automation tasks. Solutions are shown in interplay with multiple components in the system -

separated from the focus in individual products.

You can find Applications & Tools on the Internet

(http://support.automation.siemens.com/WW/view/en/20208582).

CAx Download Manager

The CAx Download Manager is used to access the current product data for your CAx or CAe

systems.

You configure your own download package with a few clicks.

In doing so you can select:

●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN

macro files

●Manuals, characteristics, operating manuals, certificates

●Product master data

You can find the CAx Download Manager on the Internet

(http://support.automation.siemens.com/WW/view/en/42455541).

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

8Manual, 07/2014, A5E03484886-AC

Product overview

2.1

Properties

Article number

6ES7531-7NF10-0AB0

View of the module

Figure 2-1 View of the AI 8xU/I HS module

Product overview

2.1 Properties

Analog Input Module AI 8xU/I HS (6ES7531-7NF10-0AB0)

Manual, 07/2014, A5E03484886-AC 9

Properties

The module has the following technical properties:

●8 analog inputs

●Voltage or current measuring type can be set per channel

●Resolution 16 bits including sign

●Configurable diagnostics (per channel)

●Hardware interrupt on limit violation can be set per channel (two low and two high limits

per channel)

●High-speed update of measured values

The module supports the following functions:

Table 2- 1 Version dependencies of the module functions

Function

Firmware version

of the module

Configuration software

STEP 7

(TIA Portal)

GSD file in STEP 7

(TIA Portal) V12 or higher, or

STEP 7 V5.5 SP3 or higher

Firmware update

V1.0.0 or higher

V12 or higher

Identification data I&M0 to I&M3

V1.0.0 or higher

V12 or higher

Parameter assignment in RUN

V1.0.0 or higher

V12 or higher

Isochronous mode

V1.0.0 or higher

V12 or higher

---

Calibration in runtime

V1.0.0 or higher

V12 or higher

Module-internal Shared Input (MSI) V2.0.0 or higher V13 Update 3 or

higher

(PROFINET IO

only)

(PROFINET IO only)

Configurable submodules / submodules for

Shared Device

V2.0.0 or higher V13 Update 3 or

higher

(PROFINET IO

only)

(PROFINET IO only)

Configurable after interface module

IM 155-5 DP ST

V2.0.0 or higher V13 or higher X

You can configure the module with STEP 7 (TIA Portal) and with a GSD file.

Andere Handbücher für Simatic S7-1500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Bedienungsanleitung

Siemens

Siemens FDCIO223 Leitfaden

Siemens

Siemens SIMATIC ET 200AL Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA DQ 32x24VDC/0.5A HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens 6ES7521-1BL00-0AA0 Bedienungsanleitung

Siemens

Siemens Simatic CFU Kurzanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200iSP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens FDCI222 Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens EA12 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200AL Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens ZN-31U Bedienungsanleitung

Siemens

Siemens SIMATIC 6DL1193-6AR00-0AA0 Technisches Dokument

Siemens

Siemens ION PROFIBUS DP SPY T001 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung