Siemens SIMATIC ET 200SP Bedienungsanleitung

Product Information for BaseUnits

(6ES7193-6BP...) manual

___________________

SIMATIC

ET 200SP

Product Information for BaseUnits

(6ES7193-6BP...) manual

Product Information

03/2014

A5E33470493

-AA

Security information

Product overview

Wiring

Technical specifications

Siemens AG

Indus

try Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E33470493-AA

Ⓟ

04/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Product Information for BaseUnits (6ES7193-6BP...) manual

Product Information, 03/2014, A5E33470493-AA 3

Table of contents

1 Security information ................................................................................................................................ 4

2 Product overview .................................................................................................................................... 5

3 Wiring ..................................................................................................................................................... 7

4 Technical specifications .......................................................................................................................... 9

Product Information for BaseUnits (6ES7193-6BP...) manual

4Product Information, 03/2014, A5E33470493-AA

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, solutions, machines, equipment and/or networks. They are

important components in a holistic industrial security concept. With this in mind, Siemens’

products and solutions undergo continuous development. Siemens recommends strongly

that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable

preventive action (e.g. cell protection concept) and integrate each component into a holistic,

state-of-the-art industrial security concept. Third-party products that may be in use should

also be considered. You can find more information about industrial security on the Internet

(http://www.siemens.com/industrialsecurity).

To stay informed about product updates as they occur, sign up for a product-specific

newsletter. You can find more information on the Internet

(http://support.automation.siemens.com).

Product Information for BaseUnits (6ES7193-6BP...) manual

Product Information, 03/2014, A5E33470493-AA 5

Product overview

Note when you use the AUX terminals as a PE busbar:

NOTICE

If AUX is used as PE, AUX must be identified as green-yellow (e.g., gn/ye contact carrier

covers). You must remove these identifications if the terminals are no longer used as PE

Order number

6ES7193-6BP20-0BF0

View

Figure 2-1 BaseUnit BU20-P8+A4+0B

Product overview

Product Information for BaseUnits (6ES7193-6BP...) manual

6Product Information, 03/2014, A5E33470493-AA

Properties

●BaseUnit suitable for all I/O modules of the BaseUnit type "F0". Can be recognized by the

last two digits of the order number.

–Current carrying capacity per process terminal (terminals 1 to 4 and 9 to 12): Max. 5 A

●The BaseUnit continues the potential group with the power busbars P1, P2 and the

AUX bus of the left neighbor module (BaseUnit).

●Access to the AUX bus via terminals 1A to 4A

●8 terminals to the process (assignment with the I/O module)

●Connection technology in the form of push-in terminals

Product Information for BaseUnits (6ES7193-6BP...) manual

Product Information, 03/2014, A5E33470493-AA 7

Wiring

Pin assignment

Terminals of a potential group

Fail-safe module

Overvoltage category 3

Non-fail-safe module

Overvoltage category 2

1 to 4 Up to 230 V AC/DC (AC only one phase)

Assignment is determined by the I/O module.

See I/O module manual

(http://support.automation.siemens.com/WW/view/en/55679691/133300)

9 to 12 Safe extra low voltage SELV/PELV

Assignment is determined by the I/O module.

See I/O module manual

(http://support.automation.siemens.com/WW/view/en/55679691/133300)

P1, P2, AUX (1A to 4A) SELV/PELV

(max. 10 A)

SELV/PELV

Up to 230 V AC/DC (AC only one phase)

(max. 10 A)

The AUX terminals may only be used with an identical voltage or PE associated with the

supply voltage.

Wiring

Product Information for BaseUnits (6ES7193-6BP...) manual

8Product Information, 03/2014, A5E33470493-AA

Block diagram

①

Backplane bus

②

I/O module

③

Terminals with connection to the I/O module

④

Connected power busbars without connection to the terminals

⑤

Connected AUX bus with connection to the terminals

Figure 3-1 Block diagram BU20-P8+A4+0B

Product Information for BaseUnits (6ES7193-6BP...) manual

Product Information, 03/2014, A5E33470493-AA 9

Technical specifications

Technical specifications of the BaseUnit BU20-P8+A4+0B

6ES7193-6BP20-0BF0

Product type designation

BU20-P8+A4+0B

Supply voltage

Rated value (DC)

24 V

Rated value (AC)

230 V; 110 V

Current carrying capacity

Current carrying capacity up to 60 °C, max.

10 A

Electrical isolation

between backplane bus and supply voltage

Yes

between process terminals and supply voltage

Yes

between Powerbus and supply voltage

Yes

Insulation

Insulation tested with

3250 V DC 1 min (type test); 2545 V DC 2 s

(routine test)

Ambient conditions

Operating temperature

Horizontal installation, min.

0 °C

Horizontal installation, max.

60 °C

Vertical installation, min.

0 °C

Vertical installation, max.

50 °C

Dimensions

Width

20 mm

Height

117 mm

Weights

Weight, approx.

48 g

Mechanical and climatic ambient conditions

Contrary to the specifications for mechanical ambient conditions and the test of mechanical

ambient conditions from the section "Mechanical and climatic ambient conditions" in the

system manual ET 200SP distributed I/O system, the following applies to this BaseUnit:

Technical specifications

Product Information for BaseUnits (6ES7193-6BP...) manual

10 Product Information, 03/2014, A5E33470493-AA

Mechanical ambient conditions

The following table shows the mechanical ambient conditions in the form of sinusoidal

vibrations.

Table 4- 1 Mechanical ambient conditions

Frequency range

ET 200SP with BusAdapter

BA 2×FC

ET 200SP with BusAdapter

BA 2×RJ45/ BA 2xSCRJ

5 ≤f ≤8.4 Hz

3.5 mm amplitude

8.4 ≤f ≤150 Hz

1 g constant acceleration

Tests of mechanical ambient conditions

The following table provides important information with respect to the type and scope of the

tests of ambient mechanical conditions.

Table 4- 2 Tests of mechanical ambient conditions

Test of ...

Test standard

Note

Vibration Vibration test

according to

IEC 60068-2-6 (Sinus)

Type of vibration: Frequency sweeps with a rate of change

of 1 octave/minute.

•5 Hz ≤f ≤8.4 Hz, 3.5 mm constant amplitude

•8.4 Hz ≤f ≤150 Hz, 1 g constant acceleration

Duration of vibration: 10 frequency sweeps per axis at each of three

vertically aligned axes

Shock Shock, tested

according to

IEC 60068-2-27

Type of shock: Half-sine

Shock intensity: 150 m/s2peak value, 11 ms duration

Direction of shock: 3 shocks in each direction (+/-) at each of three

vertically aligned axes

Andere Handbücher für SIMATIC ET 200SP

101

Dieses Handbuch passt für folgende Modelle

Andere Siemens E/A-System Handbücher

Siemens

Siemens SIMATIC ET 200iS Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens FDCIO223 Leitfaden

Siemens

Siemens 6ES7521-1BL00-0AA0 Bedienungsanleitung

Siemens

Siemens DQ 16x24VDC/0.5A HF Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200eco PN Technisches Dokument

Siemens

Siemens PPM-1U32.BPR Bedienungsanleitung

Siemens

Siemens FDCI361 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200L Bedienungsanleitung

Siemens

Siemens N 263E11 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Benutzerhandbuch

Siemens

Siemens SIMATIC S5 CP 523 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic series Bedienungsanleitung

Siemens

Siemens Binary Input N 260 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200eco Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP HA Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens simatic ET 200MP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung