Siemens FDCIO181-1 Bedienungsanleitung

Building Technologies

Control Products and Systems

FDCIO181-1 Input/Output Module

Product Manual

Characteristic

lMicroprocessor-controlled signal evaluation

lAutomatic address setting, without encoder settings or DIP switch

l1 monitored input, 1 monitored output

lLED display of input and output status

lInput lines monitored for open line or short/open circuit

lPrevention of noise interference through intelligent analysis of input signals

lOutput lines monitored for open line or short/open circuit (when potential output not

activated)

lOutput monitoring configurable(on/off)

lControl output for equipment 24 VDC, max. 2 A

lCommunication with controller via FD18-BUS(detector line)

lDirectly used in dry areas. Applicable in dusty and humid areas when installed in FDCH221

housing

l“Sticker Method” easy for commissioning

Application

Input

With the input a status can be monitored, the input can be configured by controller or

configuration tools as follows:

l“Status“input or “Alarm“input

lLead monitoring for open line or open line and short circuit

lWhen inputting status, according to different status of contact, can be set as fallows:

– Normal mode: normally open NO input

– Inverted mode: normally closed NC input

Fig. 1 connection diagram of dry contact input

Building Technologies A6V10436766_b_en_--

Fire Safety 2014-11-27

Status” inputs and alarm” inputs

“Alarm“ inputs trigger an alarm as soon as the input is activated. “Status“ inputs trigger a

monitoring status change as soon as they are activated.

Line monitoring and circuitry

The input lines are monitored for open line or open line and short circuit. To make these

possible, resistors must be properly connected to the end of lines of the input (Fig. 1). When

an open line or a short circuit occurs on one of the input lines, a fault message is transmitted

to the control panel. The input must be potential-free.

Output

External power output (Default)

Normal operation (output lines monitored)

-Be used for controlling (e.g. operating a horn/strobe).

-The module switches the externally supplied 24 VDC voltage in active status on the

output.

-In inactive status the output line is monitored for open line and short circuit (Fig. 3).

-The jumper on the input/output module must be plugged onto J2 (Fig. 2)

Fig.2 Input/output module jumper position J2

Fig.3 Connection for normal operation with output line monitored for short circuit and open line

Configuration

The following configurations are possible through controller or configuration tool:

lAfter activating the output remains:

‒Steady output

‒Pulse output: How long the contact remains active can be configured by controller or

configuration tools (pulse duration).

lFailsafe behavior when the FD18-BUS detector line is current-free or in degraded mode.

The error behavior defines the position of the output in case of an error:

‒Off: Output remains in the same position as before the error

‒Activation: Output is activated in case of an error

‒Deactivation: Output is deactivated in case of an error

The controller does not monitor external equipment status (activated/inactivated).

Inverted operation (output lines not monitored)

-Be used for controlling (e.g. closing a door).

-The module switches the externally supplied 24 V DC voltage in active status on the

output.

-In normal status there is no monitoring for open line and short circuit.

-The jumper on the input/output module must be plugged onto J2 (Fig. 4).

N5404

Building Technologies A6V10436766_b_en_--

Fire Safety 2014-11-27

Fig. 4 Input/output module jumper position J2

Fig. 5 Connection diagram for inverted operation, e.g. when used as door retainer.

In inactive status the 24 V DC are permanently applied to the output and may keep a door

open, for example. When the output is switched to active, the output goes into "open" status

(= no 24 V DC voltage) and the door is closed.

Comment:

In this example, the door would also close if the 24 VDC supply were to fail, e.g. due to a line

problem (short circuit, open line).

Configuration

Under inverted mode, the following configurations are possible through controller or

configuration tools :

lAfter activating the output remains:

‒Steady output

‒Pulse output: How long the contact remains active can be configured by controller or

configuration tools (pulse duration).

lFailsafe behavior when the FD18-BUS detector line is current-free or in degraded mode.

The error behavior defines the position of the output through controller or configuration

tools in case of an error :

‒Off: Output remains in the same position as before the error

‒Activation: Output is activated in case of an error

‒Deactivation: Output is deactivated in case of an error

The controller does not monitor external equipment status (activated/inactivated).

Dry contact output

Potential-free contact (Output not monitored)

-Be used for controlling (e.g. closing a door).

-Output control is not monitored.

-An externally supplied 24 V DC voltage is not needed.

-The jumper on the input/output module must be plugged onto J1 (Fig. 6).

Fig.6 Input/output module jumper position J1

Fig. 7 Connection diagram for potential-free contact output

Building Technologies A6V10436766_b_en_--

Fire Safety 2014-11-27

Configuration

The following configurations are possible by controller or configuration tools :

lThe contact is active, when:

‒Normal mode: normally open NO closes

‒Inverted mode: normally closed NC opens

lAfter activating the output remains:

‒Steady output

‒Pulse output: How long the contact remains active can be configured by controller or

configuration tools (pulse duration).

lFailsafe behavior when the FD18-BUS detector line is current-free or in degraded mode.

The error behavior defines the position of the output through controller or configuration

tools in case of an error:

‒Off: Output remains in the same position as before the error

‒Activation: Output is activated in case of an error

‒Deactivation: Output is deactivated in case of an error

The controller does not monitor external equipment status (activated/inactivated).

Structure

The module consists of the module carrier, the printed circuit board, the cover and the

protection cover. The printed circuit board includes the LEDs. The LEDs indicate the states of

the inputs/outputs. The cover of the printed circuit board is transparent, so that the state of the

LEDs is visible even when the housing is closed.

To protect the modules from environmental influences, housing FDCH221 is optional.

Fig.8 Overview

Legend

1. Input 5. LED indicator

2. Detection line 6. Jumper

3./ 4. Output

Jumper

Jumper position Signification

Output is not monitored.

Output is monitored.(factory default)

If the configurations on the control panel and jumper don't match, this is recognized and an

error message is triggered.

Any other jumper position is not allowed.

Building Technologies A6V10436766_b_en_--

Fire Safety 2014-11-27

LED indicator

For each input/output, one red LED indicates the status.

LED Signification

Off Normal operation, in/output is monitored.

Flashes every 1 s, 250ms on Input/output activated

Input LED flashes every 1s, 2...5ms on Localization mode

Installation

Fig. 9 Fig. 10 Fig. 11

Fig. 12 Detection line connection

Preparation

1. Determine type of installation:

– Installation outside a switching cabinet or a control unit:

use FDCH221 housing (Fig. 10) .

– Installation directly in a switching cabinet or a control unit:

mount the module on an even surface (Fig. 9).

Damage by water!

In humid or wet environments always use FDCH221 housing!

Mounting FDCH221 housing

1. Open the housing.

2. Determine the position of the cable entries in the housing

and break them out.

3. Mount the housing on an even surface with two screws

(Fig. 10). Distance between holes: 182.0±1.0mm.

4. Insert the cables and fix the cables in the housing.

5. Insert the seal and fix the lid additionally with four screws

(Fig. 11) (only this way is IP65 protection guaranteed).

The housing lid is transparent. Consider a suitable

installation position to make sure that the LEDs of the

module are visible at any time.

Procedure with installation in the housing

CAUTION

Overheating of the input/output module!

1. Open the housing.

2. Place the module in the housing and fix it with two

screws (Fig. 9/10).

3. Close the housing.

Procedure with installation on an even surface

1. Place the module on an even surface.

2. Fix the module with two screws (M4 X15) (Fig. 9).

Distance between holes: 63.5±1.0mm

Electric connection

1. Referring to Fig. 1,3,5,7,12 connect the cables to the

corresponding terminals.

2. Connect resistor/ diode .The resistors must be

connected at the end of the monitored line.

3. Fix the cables to the module

CAUTION

Mind the positive and negative polar when connecting the

diodes.

Beijing Siemens Cerberus Electronics Limited

No.1,Fengzhidonglu, Xibeiwang, HaiDian District,

Beijing, 100094, China

Tel: +10 6476 8806

Fax: +10 6476 8899

Doc No. A6V10436766_b_en_-- Manual FD18

Edition 2014-11-27 101518899

Dimension In:mm

Specification

Operating voltage 12 … 32 VDC

Operating current (quiescent) 0.31 mA

Activation current 0.51 mA

Output

-Capacity

-Monitoring resistor

-Diode

2 A @ 24 VDC

3.3k Ω(1/4w)

1N5404

Input

-Monitoring resistor 3.3k Ω/ 680 Ω

Operating temperature 0 … +42 °C

Storage temperature –20 … +75 °C

Humidity ≤95 % rel.

Communication protocol FD18-BUS

Load factors 3

Connection terminals 1.0 … 1.5 mm2

Color

–Housing

–Cover white, RAL 9010

transparent

Protection category EN60529/IEC529/GB4208-93

–With FDCH221 housing IP65

Details for ordering

Type Material No. Part No. Designation Weight

FDCIO181-1 S54322-F8-A1 101451422 Input/output module 0.093 Kg

FDCH221 S54312-F3-A1 100686595 Housing (IP65) 0.250 Kg

Inhaltsverzeichnis

Andere Siemens E/A-System Handbücher

Siemens

Siemens APACS+ Handbuch

Siemens

Siemens 6ES7134-4NB01-0AB0 Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Technisches Dokument

Siemens

Siemens TX-I/O Bedienungsanleitung

Siemens

Siemens UP 220 Service-Handbuch

Siemens

Siemens 6DL2804 Series Montageanleitung

Siemens

Siemens Simatic S7-1500 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200M Bedienungsanleitung

Siemens

Siemens BANY Agent Administratorhandbuch

Siemens

Siemens 6ES7134-4JB00-0AB0 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200PA SMART Administratorhandbuch

Siemens

Siemens SIMATIC ET 200SP HA Technisches Dokument

Siemens

Siemens S7-I/O Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200eco PN Bedienungsanleitung

Siemens

Siemens FDCIO223 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200R Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC 6ES7134-4FB01-0AB0 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens MICROMASTER 440 GX Technische Daten

Siemens

Siemens SIMATIC ET 200S Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200AL Benutzerhandbuch

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung