Siemens SIMATIC ET 200SP Bedienungsanleitung
SIMATIC
ET 200SP HA
Digital output module DQ
16x24VDC/0.5A
(6DL1132-6BH00-0PH1)
Manual
05/2017
A5E39265993-AA
Security information 1
Product overview 2
Wiring 3
Parameters 4
Displays and interrupts 5
Technical specifications 6
Drivers, parameters,
diagnostics messages and
address space A
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E39265993-AA
Ⓟ 05/2017 Subject to change
Copyright © Siemens AG 2017.
All rights reserved
Table of contents
1 Security information......................................................................................................................................5
2Product overview..........................................................................................................................................7
2.1 Properties of the I/O module DQ 16x24VDC/0.5A HA.............................................................7
3Wiring...........................................................................................................................................................9
3.1 Terminal assignment of the I/O module DQ 16x24VDC/0.5A HA............................................9
3.2 Schematic circuit diagram......................................................................................................11
4 Parameters.................................................................................................................................................13
4.1 Parameters of the I/O module DQ 16x24VDC/0.5A HA.........................................................13
4.2 Module/channel parameters...................................................................................................14
4.3 Explanation of the module/channel parameters.....................................................................15
5 Displays and interrupts...............................................................................................................................17
5.1 Status and error displays of the I/O module DQ 16x24VDC/0.5A HA....................................17
5.2 Interrupts................................................................................................................................20
6 Technical specifications..............................................................................................................................21
A Drivers, parameters, diagnostics messages and address space...............................................................25
A.1 Concept of the driver and diagnostics blocks.........................................................................25
A.2 Parameter assignment...........................................................................................................27
A.3 Parameter assignment and structure of the module/channel parameters.............................28
A.4 Diagnostics messages and maintenance events...................................................................31
A.5 Address space.......................................................................................................................33
Index...........................................................................................................................................................35
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
Manual, 05/2017, A5E39265993-AA 3
Table of contents
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
4Manual, 05/2017, A5E39265993-AA
Security information 1
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines and
networks. Systems, machines and components should only be connected to the enterprise
network or the internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit:
http://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends to apply product updates as soon as available and to always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
http://www.siemens.com/industrialsecurity.
Validity of the documentation
This device manual describes the DQ 16x24VDC/0.5A HA I/O module with the article number
6DL1132-6BH00-0PH1.
It complements the system manual for the ET 200SP HA Distributed I/O System.
Functions that generally relate to the system are described in this manual.
The information in this device manual and the system/function manuals enables you to put the
ET 200SP HA into operation.
Appendices
The appendices provide information that is relevant for using the ET 200SP HA outside the
PCS 7 environment.
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
Manual, 05/2017, A5E39265993-AA 5
Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Security information
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
6Manual, 05/2017, A5E39265993-AA
Product overview 2
2.1 Properties of the I/O module DQ 16x24VDC/0.5A HA
View of the module
DIAG MT
DQ HA
16x24VDC/ 0,5A
7
DQ . 6 +
8
1
DQ . 0 +
2
3
DQ . 2+
4
5
DQ . 4 +
6
1P1
L+
24VDC
M
1P2
2P1
L+
24VDC
M
2P2
MAX. 10 A
.0 .1
V 1.0.0
CC 02
PW R
6DL1132-6BH00-0PH1
X 2
34
DQ . 7+
DQ .1+
DQ . 3 +
DQ . 5 +
DQ a
15
DQ . 6 +
16
9
DQ . 0 +
10
11
DQ . 2+
12
13
DQ . 4 +
14
DQ . 7+
DQ.1+
DQ . 3 +
DQ . 5 +
DQ b
2324
17 18
19 2 0
2122
M
31
25
27
29
32
26
28
30
F0 F1
.2 . 3
F2 F 3
.4 .5
F4 F 5
.6 .7
F6 F 7
.0 .1
F0 F 1
.2.3
F2F3
.4 .5
F4F5
.6.7
F6 F 7
DQ b DQ a
①Module type and designation ⑧Output disable switch
②LED for diagnostics ⑨Module type color coding
③LED for maintenance ⑩Product version
④2D matrix code ⑪Function status and firmware version
⑤Wiring diagram ⑫Color code for selection of the color-coded labels
⑥LEDs for channel status/channel
fault
⑬Serial number
⑦LED for supply voltage ⑭Article number
Figure 2-1 View of the DQ 16×24VDC/0.5A HA
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
Manual, 05/2017, A5E39265993-AA 7
Properties
The I/O module has the following technical properties:
● 16 digital outputs with the following properties that can be individually configured for each
channel
– Configurable diagnostics
– Configurable substitute values
● Source output (PNP, switching to P potential)
● Module-specific configurable diagnostics for missing supply voltage L+
● Output current 0.5 A per channel
● Suitable for solenoid valves, DC contactors, and indicator lights
The I/O module supports the following functions:
● Firmware update
● I&M identification data
● Parameter reassignment in RUN
● Value status QI
● IO redundancy
● Output disable switch
You can configure the I/O module with HW Config and integrate it into your system.
Output disable switch
If you want to pull the I/O module in runtime, you have to press the output disable switch for
3 seconds for the I/O module to be deenergized.
When the output disable switch has been pressed for 3 seconds, the LED DIAG flashes red,
the LED MT lights up yellow and the I/O module generates a diagnostics message. See section
Status and error displays of the I/O module DQ 16x24VDC/0.5A HA (Page 17).
Note
Pressing the output disable switch interrupts any ongoing firmware update. A firmware update
cannot be performed when the device is deenergized.
Accessories
The following accessories must be ordered separately:
● Labeling strips
● Color-coded labels
● Reference identification label
● Shield connector
Product overview
2.1 Properties of the I/O module DQ 16x24VDC/0.5A HA
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
8Manual, 05/2017, A5E39265993-AA
Wiring 3
3.1 Terminal assignment of the I/O module DQ 16x24VDC/0.5A HA
Terminal blocks
You can operate the I/O module with the following terminal blocks:
● 6DL1193-6TP00-0DH1, light
● 6DL1193-6TP00-0BH1, dark
● 6DL1193-6TP00-0DM1, light, for redundant configuration
● 6DL1193-6TP00-0BM1, dark, for redundant configuration
The terminal block is not included in the scope of delivery of the I/O module and must be
ordered separately.
Note
You can find additional information on the configuration in the system manual.
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
Manual, 05/2017, A5E39265993-AA 9
General pin assignment
Table 3-1 Pin assignment of the DQ 16×24VDC/0.5A HA
Terminal Assignment Terminal Assignment Description
1DQ a/DQ.0+ 2DQ a/DQ.1+ DQ a /DQ.n+: Output signal, channel n (0…7)
DQ b /DQ.n+: Output signal, channel n (8…15)
M: Ground
1P1: Supply voltage L+ of the voltage bus 1P
2P1: Supply voltage L+ of the voltage bus 2P
1P2: Ground reference of the voltage bus 1P
2P2: Ground reference of the voltage bus 2P
7
DQ .6+
8
1
DQ .0+
2
3
DQ .2+
4
5
DQ .4 +
6
1P1
L+
24VDC
M
1P2
2P1
L+
24VDC
M
2P2
MA X. 10 A
DQ .7+
DQ .1+
DQ .3 +
DQ .5+
DQ a
15
DQ .6+
16
9
DQ .0+
10
11
DQ .2+
12
13
DQ .4 +
14
DQ .7+
DQ .1+
DQ .3 +
DQ .5+
DQ b
23 24
17 18
19 20
21 22
M
31
25
27
29
32
26
28
30
3DQ a/DQ.2+ 4DQ a/DQ.3+
5DQ a/DQ.4+ 6DQ a/DQ.5+
7DQ a/DQ.6+ 8DQ a/DQ.7+
9DQ b/DQ.0+ 10 DQ b/DQ.1+
11 DQ b/DQ.2+ 12 DQ b/DQ.3+
13 DQ b/DQ.4+ 14 DQ b/DQ.5+
15 DQ b/DQ.6+ 16 DQ b/DQ.7+
17 M18 M
19 M20 M
21 M22 M
23 M24 M
25 M26 M
27 M28 M
29 M30 M
31 M32 M
1P1 L+ 1P2 M
2P11L+ 2P2 M
1-wire
'4Q0'4Q'4Q
2-wire
'4Q0
1If the module is plugged into a TB45R-P32 terminal block suitable for IO redundancy, the potential at this terminal is 1P3.
Note
The M terminals are intended exclusively for the 1 or 2-wire connection system. You may not
use these terminals as the ground terminals for other devices in the system. Ensure that the
total current does not exceed 2A for each M terminal.
Wiring
3.1 Terminal assignment of the I/O module DQ 16x24VDC/0.5A HA
Digital output module DQ 16x24VDC/0.5A (6DL1132-6BH00-0PH1)
10 Manual, 05/2017, A5E39265993-AA
Andere Handbücher für SIMATIC ET 200SP
101
Inhaltsverzeichnis
Andere Siemens E/A-System Handbücher
Siemens
Siemens SIMATIC ET 200SP Technisches Dokument
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC IM151-1 STANDARD Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200S Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200S Bedienungsanleitung
Siemens
Siemens FDCIO223 Leitfaden
Siemens
Siemens SIMATIC PROFINET Stücklistenhandbuch
Siemens
Siemens FDCL221 Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200S Bedienungsanleitung
Siemens
Siemens SIMATIC ET 200SP Bedienungsanleitung
Siemens
Siemens SIMATIC S5 CP 523 Bedienungsanleitung
Siemens
Siemens Simatic S7-1500 Technisches Dokument
Siemens
Siemens CASTOMAT ION ANALOGINPUT T001 Bedienungsanleitung
Siemens
Siemens FDCIO181-1 Bedienungsanleitung
Siemens
Siemens 6ES7134-4JB00-0AB0 Bedienungsanleitung
Siemens
Siemens Simatic S7-300 Bedienungsanleitung
Siemens
Siemens Simatic S7-1500 Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
