Siemens FDCI181-1 Bedienungsanleitung

Building Technologies

Control Products and Systems

FDCI181-1 Input Module

Product Manual

Characteristic

l1 monitored digital input

lInput lines are monitored for open line and short/open circuit (terminal resistors is

mandatory)

lMicroprocessor-controlled signal evaluation

lPrevention of noise interference through intelligent analysis of input signals

lLED display of input status

lAutomatic address setting, without encoder settings or Dip-switch

lPower supply via FD18-BUS

lCommunication with controller via FD18-BUS(detection line)

lDirectly used in dry areas, Applicable in dusty and humid areas when installed in

FDCH221 housing

l“Sticker Method” easy for commissioning

Application

With the input a status can be monitored, the input can be configured by controller or

configuration tools as follows:

l“Status“input or “Alarm“input

lLead monitoring for open line or open line and short circuit

lWhen inputting status, according to different status of contact, can be set as

follows:

-Normal mode: normally open input

-Inverted mode: normally closed input

Building Technologies A6V10436763_b_en_--

Fire Safety 2014-11-27

“Status” inputs and “Alarm” inputs

“Alarm“ inputs trigger an alarm as soon as the input is activated. “Status“ inputs trigger a

monitoring status change as soon as they are activated.

Line monitoring and circuitry

The input lines are monitored for open line or open/short line. To make these possible,

resistors must be properly connected to the end of lines of the input (Fig.6). When an

open line or a short line occurs on one of the input lines, a trouble message is

transmitted to the control panel.

The input must be potential-free.

Structure

The module consists of the module carrier, the printed circuit board, the cover and the

protection cover. The printed circuit board includes the LEDs. The LEDs indicate the

status of the inputs. The cover of the printed circuit board is transparent, so that the state

of the LEDs is visible even when the housing is closed.

To protect the modules from environmental influences, there are additional options for

the housing.

Fig. 1 Overview

Legend:

1. Input

2. Detection line

3. LED indicator

LED indicator

LED indicator is used for displaying status of input.

Status LED Meaning

Off Normal operation

LED flashing every 1 s (250 ms ON) Input activated

LED flashing every 1 s (short flashes) Localization mode

Building Technologies A6V10436763_b_en_--

Fire Safety 2014-11-27

Installation

Fig. 2 Fig. 3 Fig. 4

Fig. 5 Fig. 6

Preparation

Determine the type of installation: there are 2 types of

installation for FDCI181-1 Input module:

–Installation outside a switching cabinet or a control unit:

use FDCH221 housing (Fig. 3) .

–Installation directly in a switching cabinet or a control

unit: mount the module on an even surface (Fig.2).

Damage by water!

In humid or wet environments always use the housing

FDCH221!

Installation of FDCH221 Housing

1. Open the housing.

2. Determine the cable entries in the housing and break

these open.

3. Use two screws (M 4) to fit the housing on a plane

surface (Fig. 3). Distance between holes: 182.0±1.0mm.

4. Fix and guide in the cables with waterproof joint

(provided by users themselves).

5. Fix the lid additionally with four screws (Fig. 4). (Onl

y this

way is IP65 protection guaranteed.)

The housing lid is transparent. Consider a suitable

installation position to make sure that the LEDs of the

module are visible at any time.

Installation of module in FDCH221 housing

Caution!

Overheating of FDCI81-1 input module.

1. Open the housing.

2. Fix module with two screws in the housing (Fig. 3).

3. Close the housing.

Installation on an even surface

1. Position module on an even surface (Fig. 2).

2. Fix module with two M4 screws. Distance between

holes:63.5±1.0mm.

Electric connection

1. Connect the cables to the terminals according to Fig.

5/6.

Connect only one wire per terminal!

2. Connect the resistors to the end of the monitored line.

1 resistors of 3.3KΩand 1 of 680Ωare delivered with

the product.

Beijing Siemens Cerberus Electronics Limited

No.1,Fengzhidonglu, Xibeiwang, HaiDian District,

Beijing, 100094, China

Tel: +10 6476 8806

Fax: +10 6476 8899

Doc No. A6V10436763_b_en_-- Manual FD18

Edition 2014-11-27 101518897

Dimension

In:mm

Specification

Operating voltage 12 … 32 VDC

Operating current(Quiescent) 0.27 mA

Activation current 0.37 mA

Monitoring resistors 3.3KΩ(1/4w) / 680Ω(1/4w)

Operating temperature 0 … +42 °C

Storage temperature –20 … +75 °C

Humidity ≤95 %

Communication protocol FD18-BUS

Load factors 3

Connection terminals 1.0 … 1.5 mm2

Color

–Housing

–Cover white，RAL 9010

transparent

Protection category EN60529/IEC529/GB4208-93

–With housing FDCH221 IP65

Details for ordering

Type Material No. Part No. Designation Weight

FDCI181-1 S54322-F7-A1 101451421 Input module 0.080 kg

FDCH221 S54312-F3-A1 100686595 Housing(IP65) 0.250 kg

Andere Siemens E/A-System Handbücher

Siemens

Siemens DQ 4x24VDC/2A HS Bedienungsanleitung

Siemens

Siemens BANY Agent Administratorhandbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC S5 Bedienungsanleitung

Siemens

Siemens SIMATIC TI505 Bedienungsanleitung

Siemens

Siemens FDCI222 Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simantic ET200SP Benutzerhandbuch

Siemens

Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 / ET 200MP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Benutzerhandbuch

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC Bedienungsanleitung

Siemens

Siemens Simatic CFU Kurzanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic S7-1500 Technisches Dokument

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic CFU Kurzanleitung

Siemens

Siemens SIMATIC ET 200SP Bedienungsanleitung

Siemens

Siemens Simatic ET200pro Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung