Siemens Sitrans F Series Bedienungsanleitung

SITRANS F

SITRANS MAG 3100 / 3100HT / 3100P / 5100W

Quick Start

Edition 03/2009 - Revision 01

Electromagnetic flowmeter, types 3100 / 3100HT / 3100P / 5100W

MAG 3100 / 3100HT / 3100P / 5100W

Items supplied

For more information see the operating instructions on the enclosed CD-ROM.

Order no.: A5E02451851-01

Quick Start MAG 3100 / 3100HT / 3100P / 5100W

Before installing, including in hazardous areas, refer to the operating instructions on the enclosed CD-ROM.

It contains detailed safety regulations, information and specifications which must be observed when

installing. Changes can occur. Documentations and approvals can be found on the Internet at

www.siemens.com/flowdocumentation.

Caution!

Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as

well as careful operation and maintenance. Only qualified personnel should install or operate this instrument.

General instructions

For safety reasons it is important that the following points are read and understood before the

installation of the equipment:

• Installation, connection, commissioning and service must be carried out by personnel qualified and

authorized to do so.

• It is the responsibility of the customer that the instructions and directions provided in the Quick Start and

in the operating instructions on the enclosed CD-ROM are read, understood and followed by the relevant

personnel before installing the equipment.

• It is the responsibility of the customer to instruct and authorize personnel to operate the equipment.

• It is the responsibility of the customer to ensure that the measuring system is connected correctly and is

in accordance with the connection diagram.

• Equipment used in hazardous areas must be Ex-approved and marked for Europe, FM for USA and CSA for

Canada. It is required that the special conditions for safe use provided in the manual and in the Ex

certificate are followed!

• Installation of the equipment must comply with national regulations. For example EN 60079-14 for the

European Community.

• Repair and service must be carried out by approved Siemens Flow Instruments personnel only.

Safety instructions

www.siemens.com/flowdocumentation

Order no.: A5E02451851-01

Handling

For more information see the operating instructions on the enclosed CD-ROM.

Inlet and outlet conditions

Recommended flow direction

Order no.: A5E02451851-01

Quick Start MAG 3100 / 3100HT / 3100P / 5100W

Flow conditions

The pipe must be completely filled with liquid!

Avoid vacuum!

Avoid vibrations!

Horizontal pipes

www.siemens.com/flowdocumentation

Order no.: A5E02451851-01

Potential equalization

For cathodic protection of pipe systems see the operating instructions on the enclosed CD-ROM.

With earthing electrodes (no futher action necessary)

(MAG 3100 (÷ PTFE/PFA), MAG 5100W)

Without earthing electrodes (MAG 3100 PTFE/PFA) in

conductive pipes

Without earthing electrodes in non-conductive pipes

Order no.: A5E02451851-01

Quick Start MAG 3100 / 3100HT / 3100P / 5100W

Use proper gaskets!

The following torque values are calculated on the basis of use of gaskets. For further calculations of

preconditions refer to the operating manual on the enclosed CD-ROM.

MAG 3100/3100HT/3100P or MAG 5100W with Ebonite liner - Max. torque

MAG 3100/3100HT/3100P or MAG 5100W with Ebonite liner -

PN6 PN10PN16PN25PN40PN63PN100

mm inch Nm F/Lbs Nm F/Lbs Nm F/Lbs Nm F/Lbs Nm F/Lbs Nm F/Lbs Nm F/Lbs

15 0,5“ N/A N/A N/A N/A N/A N/A N/A N/A 10 7 N/A N/A N/A N/A

25 1“ N/A N/A N/A N/A N/A N/A N/A N/A 16 12 N/A N/A 50 37

40 1,5“ N/A N/A N/A N/A N/A N/A N/A N/A 34 25 N/A N/A 100 74

50 2“ N/A N/A N/A N/A N/A N/A N/A N/A46349066140103

65 2,5“ 10 7 N/A N/A 25 18 N/A N/A3425644711081

80 3“ 25 18 N/A N/A 25 18 N/A N/A4231826113096

100 4“ 25 18 N/A N/A 25 18 N/A N/A 72 53 136 100 190 140

125 5“ 25 18 N/A N/A 32 24 N/A N/A 114 84 200 148 250 185

150 6“ 25 18 N/A N/A 50 37 N/A N/A 144 106 275 203 210 155

200 8“ 25 18 50 37 52 38 105 77 185 137 330 244 400 295

250 10“ 25 18 50 37 88 65 160 118 300 221 500 369 550 406

300 12“ 50 37 62 46 117 86 170 125 320 236 525 387 700 517

350 14“ 50 37 60 44 120 89 240 177 450 332 750 554 1200 886

400 16“ 50 37 88 65 170 125 330 244 650 480 1100 812 N/A N/A

450 18“ 56 41 92 68 170 125 320 236 570 421 N/A N/A N/A N/A

500 20“ 53 39 103 76 230 170 390 288 740 546 N/A N/A N/A N/A

600 24“ 81 60 161 119 350 258 560 413 1220 900 N/A N/A N/A N/A

700 28“ 100 74 200 148 304 224 N/A N/A N/A N/A N/A N/A N/A N/A

800 32“ 140 103 274 202 386 285 N/A N/A N/A N/A N/A N/A N/A N/A

900 36“ 172 127 288 213 408 301 N/A N/A N/A N/A N/A N/A N/A N/A

1000 40“ 180 133 382 282 546 403 N/A N/A N/A N/A N/A N/A N/A N/A

1200 48“ 252 186 395 292 731 539 N/A N/A N/A N/A N/A N/A N/A N/A

1400 54“ 330 244 503 371 736 543 N/A N/A N/A N/A N/A N/A N/A N/A

1600 66“ 380 280 684 505 913 674 N/A N/A N/A N/A N/A N/A N/A N/A

1800 72“ 382 282 771 569 937 692 N/A N/A N/A N/A N/A N/A N/A N/A

2000 78“ 432 319 867 640 1128 832 N/A N/A N/A N/A N/A N/A N/A N/A

www.siemens.com/flowdocumentation

Order no.: A5E02451851-01

Remote installation

Step 4

Mount the connection plate in the terminal box. The SENSORPROM unit

connections will be established automatically when the connection plate is

mounted in the terminal box..

Step 5

Fit the supply and output cables respectively and tighten the cable glands to

obtain optimum sealing.

Step 1

Remove and discard the terminal box lid of the sensor. Fit the cable glands for the

supply and output cables.

Step 2

Remove the two black plug assemblies for coil and electrode in the terminal box an

connect them to their corresponding terminal numbers on the connection board.

Step 3

Connect earth wire on connection board to bottom of connection box.

Connect the 2 pin connector and 3 pin connector as shown.

Order no.: A5E02451851-01

Quick Start MAG 3100 / 3100HT / 3100P / 5100W

Remote installation

123

Relocation of Sensorprom. Refer to the relevant transmitter Quick Start

Electrical connection (fig. 4). (A) Sensor, (B) Electrode cable, (C) Coil cable, (D) Only required for ATEX

applications!

For cable specifications see the operating manual on the enclosed CD-ROM.

Make sure cable glands are firmly sealed!

www.siemens.com/flowdocumentation

Order no.: A5E02451851-01

Quick Start MAG 3100 / 3100HT / 3100P / 5100W

Andere Handbücher für Sitrans F Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Messgerät Handbücher

Siemens

Siemens SICAM Q200 7KG97 Bedienungsanleitung

Siemens

Siemens SITRANS F Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens LDS 6 Original Betriebsanleitung

Siemens

Siemens SICAM Q200 7KG97 Bedienungsanleitung

Siemens

Siemens SENTRON 3NJ69 Bedienungsanleitung

Siemens

Siemens PAC1600 Bedienungsanleitung

Siemens

Siemens Pointek CLS500 Bedienungsanleitung

Siemens

Siemens ADVIA 1800 Handbuch

Siemens

Siemens SITRANS FUP1010 Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SIPROCESS GA700 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens SENTRON PAC3200 Bedienungsanleitung

Siemens

Siemens sitrans LU01 Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SIRIUS Merkblatt

Siemens

Siemens MOBY ES030-K Bedienungsanleitung

Siemens

Siemens Sitrans LR250 Bedienungsanleitung

Siemens

Siemens Sitrans F Series Stücklistenhandbuch

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Administratorhandbuch

Siemens

Siemens 9510 Bedienungsanleitung

Siemens

Siemens SENTRON PAC3200T Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung