Siemens SITRANS FUH1010 Bedienungsanleitung

6/2014Edition

Answers for industry.

Quick Start

Ultrasonic Flowmeters

SITRANS FUH1010 IP65 NEMA 7 Compact - 7ME3601-1

SITRANS F

Ultrasonic Flowmeters

FUH1010 IP65 NEMA 7

Interface Detector Quick Start

Operating Instructions

06/2014

A5E02428148

-AA

Introduction

Installation

Commissioning

Troubleshooting

Appendix

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

Order number: A5E02428148

Ⓟ

05/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance a

re required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

Operating Instructions, 06/2014, A5E02428148-AA 3

Table of contents

1 Introduction............................................................................................................................................. 5

1.1 Items supplied................................................................................................................................5

1.2 Safety Notes...................................................................................................................................6

2 Installation ............................................................................................................................................ 13

2.1 Application Guidelines .................................................................................................................13

2.2 Mounting the Transmitter .............................................................................................................13

3 Commissioning ..................................................................................................................................... 17

3.1 Connecting Power........................................................................................................................17

3.2 RS-232 Connection......................................................................................................................19

3.3 Navigating the Menu ....................................................................................................................22

3.4 Programming the Transmitter ......................................................................................................23

3.5 Sensor Installation .......................................................................................................................32

3.5.1 General information .....................................................................................................................32

3.5.2 Installing the Sensors (Reflect Mount).........................................................................................33

3.5.3 Final Setup ...................................................................................................................................36

4 Troubleshooting .................................................................................................................................... 39

4.1 Troubleshooting ...........................................................................................................................39

4.2 Alarm Letter Codes ......................................................................................................................42

A Appendix............................................................................................................................................... 43

A.1 I/O Connections and Wiring .........................................................................................................43

A.2 Technical Data .............................................................................................................................48

Index..................................................................................................................................................... 49

Table of contents

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

4Operating Instructions, 06/2014, A5E02428148-AA

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

Operating Instructions, 06/2014, A5E02428148-AA 5

Introduction

This Quick Start is for the Siemens SITRANS FUH1010 IP65 (NEMA 7) Compact Interface

Detector. It illustrates a typical setup using D-Series sensors in the Reflect Mode (for Direct

Mode see Operating Instruction manual).

Note

This Quick Start Guide appli

es to the following FUH1010 IP65 NEMA 7 operating systems:

Version 3.03.00 and later.

1.1

Items supplied

●SITRANS FUH1010 IP65 NEMA 7 Interface Detector Transmitter

●SITRANS F Literature CD

●Quick Start

Note

For additional items refer to your packing slip.

Introduction

1.2 Safety Notes

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

6Operating Instructions, 06/2014, A5E02428148-AA

1.2

Safety Notes

Quick Start Safety Information for Hazardous Areas

DANGER

Explosion Hazard

Death, serious injury or property damage will result if unauthorized and unqualified

personnel tamper with equipment.

Restrict use and repair to qualified personnel.

DANGER

Explosion Hazard

Death or severe personal injury and/or equipment and property damage will result if proper

Hazardous (Classified) Locations installation precautions are not taken.

Restrict use and repair to qualified personnel.

DANGER

Explosion Hazard

The use of unauthorized parts in the repair of the equipment, tampering by unqualified

personnel, or operation with the cover open in a Hazardous (Classified) Location will result

in dangerous conditions which will cause death, serious injury, and/or equipment and

property damage.

Follow all safety instructions contained or referenced herein.

DANGER

Explosion Hazard

Death or severe personal injury and/or equipment and property damage will result due to

improper installation or use of this equipment when located in a Hazardous (Classified)

Location.

•Install as directed.

•Disconnect power source before servicing.

•Keep cover closed when equipment is operating.

Introduction

1.2 Safety Notes

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

Operating Instructions, 06/2014, A5E02428148-AA 7

WARNING

Qualified personnel

This flowmeter system may only be set up and used in conjunction with this Quick Start and

the instructions on the electronic media provided. Installation, maintenance and operation

of the flowmeter system may only be performed by qualified personnel. Within the context

of this Quick Start, qualified persons are defined as persons who have the skills and

knowledge related to the construction and operation of the electrical equipment and

installations and have received safety training to recognize and avoid the potentially

explosive hazards involved.

Qualified personnel possess the following qualifications

1. Is trained and authorized to energize, de-energize, clear, ground and tag circuits and

equipment in accordance with established safety practices.

2. Is trained in the proper care and use of protective equipment such as rubber gloves,

hard hat, safety glasses or face shields, flash clothing, etc., in accordance with

established safety practices.

3. Is trained in rendering first aid

Note

This Quick Start does not purport to cover all details or variations in equipment, or to provide

for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular

problems arise,

which are not covered sufficiently for the purchaser's purposes, the matter should be

referred to the local Siemens sales office (www.siemens.com). The contents of this Quick

Start shall not become part of or modify any prior or existing ag

reement, commitment or

relationship. The sales contract contains the entire obligation of Siemens. The warranty

contained in the contact between the parties is the sole warranty of Siemens. Any

statements contained herein do not create new warranties or mo

dify the existing warranty.

Quick Start Safety Information for Hazardous Areas

Note

Ratings under this heading apply to specific model families

Check Your Model Number:

FUE1010 7ME3500, FUH1010 7ME3600 and FUS1010 7ME3530 only

FM-CSA installation

Read, understand and follow all safety instructions on the electronic media provided. This

equipment is rated for use in hazardous (classified) locations as stated below and must be

installed according to the 1010-304 installation drawing provided on the media. Failure to

install the equipment in the prescribed manner will result in unsafe operation. Follow all local

jurisdictional safety codes when operating this equipment. When properly installed the

equipment meets the following FM – CSA ratings.

Introduction

1.2 Safety Notes

FUH1010 IP65 NEMA 7 Interface Detector Quick Start

8Operating Instructions, 06/2014, A5E02428148-AA

Transmitter

●Intrinsically safe connections Class I and II, Division 1, Groups A, B, C, D, E, F and G;

●Nonincendive for Class I, Division 2, Groups A, B, C and D;

●Suitable for Class II Division 2, Groups E, F and G outdoor (Type 4X), Class III (CSA

only)

●Temperature code T5 at an ambient of 40°C

Sensors

●Intrinsically safe Class I and II, Division 1, Groups A, B, C, D, E, F and G;

●Nonincendive for Class I, Division 2, Groups A, B, C and D;

●Suitable for Class II, Division 2, Groups B, E, F and G outdoor (Type 4X), Class III (CSA

only)

●Temperature code T6 at an ambient of 40°C

ATEX installation

Read, understand and follow all safety instruction on the electronic media provided. This

equipment complies with Directive 94/9/EC and is rated for use in potentially explosive

atmospheres. The equipment markings are shown and explained below. Equipment must be

installed according to the 1010-389 installation drawing provided on the media. Failure to

install the equipment in the prescribed manner will result in unsafe operation. Follow all

regional safety laws when operating this equipment. When properly installed the equipment

meets the following ATEX ratings as stated in EC-Type Examination Certificate

KEMA03ATEX1134

Transmitter Markings and Explanations

●II (1) G [Ex ia] IIC – Transmitter located in the non-hazardous area with intrinsically

safe circuits of category Ex ia, which can be connected to Category 1 Sensors

●II 3 (1) G Ex nC [ia] IIC T5 – Category 3 Transmitter located in Zone 2 explosive

atmosphere with intrinsically safe circuits of category Ex ia, which can be connected to

Category 1 Sensors in Zone 0

●IP65 – Ingress protection against solid bodies, rating of dust-tight and against liquid,

rating of water jets

Sensors Markings and Explanations

●II 1 G Ex ia IIC T5 – Category 1 Sensors located in Zone 0 explosive atmosphere with

intrinsically safe circuits of category Ex ia for use in potentially explosive atmosphere

containing gases

●IP65 – Ingress protection against solid bodies, rating of dust-tight and against liquid,

rating of water jets

Andere Handbücher für SITRANS FUH1010

Inhaltsverzeichnis

Sprachen:

Andere Siemens Messgerät Handbücher

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens SITRANS F US SONO 3300 Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens SITRANS FUE950 Bedienungsanleitung

Siemens

Siemens SITRANS FUE950 Bedienungsanleitung

Siemens

Siemens ACCESS 9340 Bedienungsanleitung

Siemens

Siemens SMART 7KT Bedienungsanleitung

Siemens

Siemens SITRANS AID IQ Bedienungsanleitung

Siemens

Siemens SIPLUS CMS2000 Administratorhandbuch

Siemens

Siemens SITRANS SL Benutzerhandbuch

Siemens

Siemens SENTRON 7KT PAC1200 Benutzerhandbuch

Siemens

Siemens SMART 7KT0311 Bedienungsanleitung

Siemens

Siemens SICAM MMU Bedienungsanleitung

Siemens

Siemens FS720 Series Betriebsanleitung

Siemens

Siemens SITRANS FS230 Administratorhandbuch

Siemens

Siemens SIWAREX WL230 BB-S SA Bedienungsanleitung

Siemens

Siemens SITRANS F C MASSFLO MASS 2100 Bedienungsanleitung

Siemens

Siemens Sitrans LR200 Bedienungsanleitung

Siemens

Siemens CASTOMAT ION ANALOGINPUT T001 Bedienungsanleitung

Siemens

Siemens 5SV8 200-6KK Service-Handbuch

Siemens

Siemens MPA 1 Series Bedienungsanleitung

Siemens

Siemens WSx6 Series Bedienungsanleitung

Siemens

Siemens 9700 Bedienungsanleitung

Siemens

Siemens sitrans LU01 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung