Siemens SMART 7KT Bedienungsanleitung

Assembly Instruction

Multi-function Meter

SMART 7KT

7KT0310

Please read and understand these instructions before installing,

operating, or maintaining the equipment.

DANGER

Hazardous voltage. Will cause death or serious

injury. Turn off and lock out all power supply to

this device before working on this device.

Replace all covers before power supplying this

device is turned on.

Contents

4 nos. Terminal Clamps Rubber Gasket x1

Cross recessed Phillips head

Installation

For installing the meter

Prepare the panel cutout with proper dimensions as shown below.

FRONT PANEL DESCRIPTION OUTLINE

Dimensions (in mm)

PANEL CUTOUT

Dimensions (in mm)

Scan the QR code for more

information

Installation (Continued)

1. Insert unit into the panel 2. Position the clamps (as shown in the

gure) and push the same into the slots in

their respective locations.

3. Push/Slide all 4 clamps towards the panel

evenly till the lowest possible tooth of the

clamp is engaged. Ensure the meter is

properly tightened and it does not move.

Note: Terminal screw tightening torque: 0.7 N-m to 0.8 N-m (6 In-Lb to 7 In-Lb)

Mounting distance

The distance to be maintained between two meters while

mounting on a panel door should be at least 100 mm.

Installation Guidelines

1. This equipment, being built-in-type, normally becomes a

part of main control panel and in such case the terminals

do not remain accessible to the end user after installation

and internal wiring.

2. Conductors must not come in contact with the internal

circuitry of the equipment or else it may lead to a safety

hazard that may in turn endanger life or cause electrical

shock to the operator.

3. Circuit breaker or mains switch must be installed between

power source and supply terminals to facilitate power ‘ON’

or ‘OFF’ function. However this switch or breaker must be

installed in a convenient position normally accessible to

the operator.

4. Before disconnecting the secondary of the external

current transformer from the equipment, make sure that

the current transformer is short circuited to avoid risk of

electrical shock and injury.

5. The equipment shall not be installed in environmental

conditions other than those mentioned in this manual.

6. The equipment does not have a built-in-type fuse.

Installation of external fuse of rating 275V AC / 0.5Amp for

electrical circuitry is highly recommended.

7. Remove the scratch-guard from the meter display during

commissioning of the panel.

Connection diagram

Circuit Diagram

3 Phase 4-Wire (commonly used)

3 Ø - 4 Wire, 3 CT’S 3 Ø - 4 Wire, 3 CT’S and 3 PT’S

2) All Fuse Type: 0.5A, Class gG

Wiring Guidelines

1. To prevent the risk of electric shock, power supply to

the equipment must be kept OFF while doing the wiring

arrangement.

2. Wiring shall be done strictly according to the terminal

layout. Conrm that all connections are correct.

3. Use lugged terminals.

4. To reduce electromagnetic interference use of wires with

adequate ratings and twists of the same in equal size shall

be made with shortest connections.

5. Layout of connecting cables shall be away from any

internal EMI source.

6. Cable used for connection to power source, must have a

cross-section of 1mm2to 2.5mm2. These wires shall have

current carrying capacity of 6A.

7. Copper cable should be used (Stranded or Single core

cable).

SACHIN ENTERPRISE

These instructions do not purport to cover all details or variations in

equipment, or to provide for every possible contingency in connection

with installation, operation, or maintenance. Should additional

information be desired, please contact the local Siemens sales ofce.

The contents of this instruction manual shall not become part of or

modify any prior or existing agreement, commitment, or relationship.

The sales contract contains the entire obligation of Siemens. The

warranty contained in the contract between the parties is the sole

warranty of Siemens. Any statements contained herein do not create

new warranties or modify the existing warranty.

Trademarks - Unless otherwise noted, all names identied by ® are

registered trademarks of Siemens AG or Siemens Industry, Inc. The

remaining trademarks in this publication may be trademarks whose

use by third parties for their own purposes could violate the rights of

the owner.

Safety Precautions

All safety related codications, symbols and instructions that

appear in this operating manual or on the equipment must

be strictly followed to ensure the safety of the operating

personnel as well as the instrument.

If the equipment is not used in a manner specied by the

manufacturer it might impair the protection provided by the

equipment.

• Do not use the equipment if there is any mechanical

damage.

• Ensure that the equipment is supplied with correct

voltage.

CAUTION:

1. Read complete instructions prior to installation and

operation of the unit.

2. Risk of electric shock.

3. The equipment in its installed state must not come in

close proximity to any heating sources, oils, steam, caustic

vapors or other unwanted process by products.

For demounting the meter

Pull the arm of the sliding clamps in outward

direction (opposite to meter) and drag the

sliding clamps away from the panel.

Dis-assemble the snap tted base clamps from

the meter using a screw-driver

Push the meter from back side out of the panel

window and remove the gasket from the meter

Published by

Siemens Malaysia Sdn Bhd

Smart Infrastructure

Electrical Products (EP)

Cp Tower, 11, Jalan 16/11

46350 Petaling Jaya, Selangor

Malaysia

[email protected]

Subject to changes and errors.

The information given in this document only contains general

descriptions and/or performance features which may not always

specifically reflect those described, or which may undergo

modification in the course of further development of the products.

Product development is a continuous process. Consequently the data

indicated in this Operating Instructions is subject to change without

prior notice. For latest issue contact our sales ofces.

Industry

Online

Support

Andere Handbücher für SMART 7KT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Siemens Messgerät Handbücher

Siemens

Siemens SITRANS FM100 Bedienungsanleitung

Siemens

Siemens 7KT1 300 Bedienungsanleitung

Siemens

Siemens SIMEAS Q80 7KG8080 Bedienungsanleitung

Siemens

Siemens 9810 Series Bedienungsanleitung

Siemens

Siemens ASZ7.5 Bedienungsanleitung

Siemens

Siemens SOMATOM Sensation Cardiac Version A60 Benutzerhandbuch

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens Sitrans F Series Bedienungsanleitung

Siemens

Siemens 3WN1 3ZX1812-0WX31-9BN1 Bedienungsanleitung

Siemens

Siemens SICAM Q200 7KG97 Bedienungsanleitung

Siemens

Siemens SIWAREX WL230 BB-S SA Technisches Dokument

Siemens

Siemens 7KT1 543 Bedienungsanleitung

Siemens

Siemens FS720 Series Leitfaden

Siemens

Siemens SITRANS LR 300 Gebrauchsanweisung

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens Sitrans FUG1010 Bedienungsanleitung

Siemens

Siemens SITRANS WF100 Bedienungsanleitung

Siemens

Siemens FIDAMAT 5E Bedienungsanleitung

Siemens

Siemens ARCADIS Avantic Installations- und Betriebshandbuch

Siemens

Siemens SICAM P 7KG7750 Bedienungsanleitung

Siemens

Siemens 13-xx-ST-SBT Series Bedienungsanleitung

Siemens

Siemens SIPROCESS GA700 Administratorhandbuch

Siemens

Siemens SITRANS F M MAG 5000 Bedienungsanleitung

Siemens

Siemens SIPART PS100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung