Siemens POLYMOBIL Plus Installationshandbuch

POLYMOBIL Plus

English

Print No.: SPR8-125.034.01.03.02 Doc. Gen. Date: 01.00

Replaces: SPR8-125.034.01.02.02

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

Start-up Instructions

POLYMOBIL Plus SPR8-125.034.01 Page 2 of 4 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

0 - 2 Revision

Chapter Page Revision

0all03

1all03

2all03

3all03

4all03

5all03

6all03

Contents 0 - 3

Siemens AG SPR8-125.034.01 Page 3 of 4 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

1 _______Requirements__________________________________________________ 1 -1

Specially marked text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -1

Tools and measurement devices required. . . . . . . . . . . . . . . . . . . . . . . . 1 -1

Safety information and protective measures . . . . . . . . . . . . . . . . . . . . . . 1 -2

Important start-up information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -4

Replacing damaged or missing screws . . . . . . . . . . . . . . . . . . . . . . . . . 1 -5

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -5

2 _______Unpacking ____________________________________________________ 2 - 1

3 _______Function checks _______________________________________________ 3 - 1

Checking the nominal line voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

Attaching the warning label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

Checking the controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2

Checking the counterbalance system . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3

Readjusting the counterbalance system with accessories attached . . . . . . . . . . 3 - 3

Checking the controls on the double-slot diaphragm . . . . . . . . . . . . . . . . . . 3 - 4

Checking the exposure release with high voltage . . . . . . . . . . . . . . . . . . . . 3 - 4

Checking the exposure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5

Custom programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5

Checking coincidence of light and radiation fields. . . . . . . . . . . . . . . . . . . . 3 - 5

4 _______Final procedures _______________________________________________ 4 - 1

Protective conductor measurement . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

Equivalent leakage current measurement . . . . . . . . . . . . . . . . . . . . . . 4 - 1

5 _______Test protocol __________________________________________________ 5 - 1

POLYMOBIL Plus Start-up protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

6 _______Changes to previous version _____________________________________ 6 - 1

Page

0 - 4 Contents

POLYMOBIL Plus SPR8-125.034.01 Page 4 of 4 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

This page intentionally left blank.

1 - 1

Siemens AG SPR8-125.034.01 Page 1 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

Specially marked text 1

Tools and measurement devices required 1

All tools and measurement devices with the exception of the standard service kit

are specified in the ARTD / Part 3.

•Standard service kit

•Protective conductor test meter

•Equivalent leakage current meter

•Digital multimeter.

"Warnings" are information provided with special emphasis when

there is

the potential for personal injury to the operator or patient.

"Cautions" are information provided with special emphasis when

there is

the potential for damage to the equipment.

"Notices" are information provided with special emphasis to facil-

itate

proper use of the equipment or proper execution of a procedure.

WARNING

CAUTION

NOTICE

Requirements 1

POLYMOBIL Plus SPR8-125.034.01 Page 2 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 2 Requirements

Safety information and protective measures 1

•When performing service work and tests, adhere to:

- the product-specific safety information in the document,

- the safety information in RA0-000.012.... in the Register of

the POLYMOBIL Plus binder,

- as well as the general safety information contained in

part 2 of the ARTD.

•Tests and adjustments that must be performed with radiation

ON, are identified by the radiation warning symbol .

Radiation protection must be worn during these types of

adjustments.

CAUTION

Requirements 1 - 3

Siemens AG SPR8-125.034.01 Page 3 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

When working with the system open, there is danger of

! Electric shock !

•The capacitor bank can still be charged.

Do not attempt to work on the system while this condition exists.

•After switching off the system, approximately 450 VDC (350 VDC

for Serial-No. < 10100) may still be present in the system; even

after disconnecting the line voltage plug. Within 10 minutes this

voltage will drop to approximately 10 V.

•Always measure the actual voltage present with the DVM at test

points -VCC and +VCC on the D960 inverter board or (more

accessible) on the D970 capacitor board at the + connection

point of capacitor C3 and on the right side of fuse F3 (refer to

Fig. 1).

•LED’s V1 ... V10 on D 970 go out at a significantly higher voltage

level and therefore they are not reliable safety indicators.

•If a fuse on the D 970 has responded, high voltage may still be

present at the affected capacitor even after a prolonged period

of time.

•The capacitor discharging circuit utilizes the D 925 board and

relays CS and LS. If connector X3 or X9 on D 925 or D 950 are not

inserted or there is a defect in the circuit, the C-bank will not

discharge.

This can cause life-threatening voltage to be present in the

system even after a prolonged period of time.

•Refer also to the POLYMOBIL Plus Service instructions

RXR8-120.061.01... "Replacing the capacitor bank".

Fig. 1

VCC

C1R3R4

WARNING

POLYMOBIL Plus SPR8-125.034.01 Page 4 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 4 Requirements

•Connect the POLYMOBIL Plus only to a line voltage supply (receptacle) that complies

with the requirements of VDE 0107 or corresponds to the local national standards.

•Disconnect the POLYMOBIL Plus at the line voltage OFF switch on the operating

console and disconnect the line voltage plug prior to any service work.

•Remove or insert boards with the generator switched OFF only; observe

ESD guidelines when handling boards.

Important start-up information 1

•After completion of the start-up procedure, the POLYMOBIL Plus which has been

completely tested and adjusted at the factory, is ready to operate.

•The POLYMOBIL Plus can be connected to nominal line voltages from 110 V AC through

230 V AC (± 10%) and automatically self-adjusts to the existing power line voltage.

•After start-up, country-specific tests are to be performed, if required;

e.g. acceptance test according to RöV (Germany - X-ray ordinance).

Acceptance test according to RöV (Germany):

Required measurements can be partially transferred from the test protocol provided.

The following values are measured at the factory and recorded in the test certificate:

- Light localizer brightness

- Filter values - visual check

- Coincidence of light field and radiation field

- X-ray tube voltage accuracy

- mAs value check

- Reproducibility of the radiation

•The test / measurement values identified by the " " symbol should be entered in the

start-up protocol located at the end of these instructions.

•Adhere to the fuse ratings for the on-site receptacle:

- 16A slow-blow (on-site) at 110 ±10% or 230V ±10% line voltage

•The line voltage cable of the POLYMOBIL Plus is supplied with a

(Schuko) safety plug.

Install line voltage plugs that comply with the local standards, if

required.

CAUTION

Requirements 1 - 5

Siemens AG SPR8-125.034.01 Page 5 of 6 POLYMOBIL Plus

Medical Engineering Rev. 03 01.00 TD SD 24

Replacing damaged or missing screws 1

•As specified in the installation drawings, damaged or missing screws may only be

replaced by steel screws conforming to DIN 267 and having the specified tensile

strength.

Cleaning 1

•The unit must always be switched off or disconnected before cleaning. Use only water to

clean the unit or a lukewarm solution consisting of water and a household cleaning

agent.

•Do not use abrasive cleaning agents or organic solvents such as benzine, alcohol or spot

remover.

•Do not spray water on the unit.

•For additional information, refer to the Operating Instructions "Cleaning/Disinfecting".

All Allen screws must have a tensile strength rating of 8.8.

CAUTION

POLYMOBIL Plus SPR8-125.034.01 Page 6 of 6 Siemens AG

Rev. 03 01.00 TD SD 24 Medical Engineering

1 - 6 Requirements

This page intentionally left blank.

Andere Handbücher für POLYMOBIL Plus

Inhaltsverzeichnis

Andere Siemens Medizinische Geräte Handbücher

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens MAGNETOM syngo MR D11 Bedienungsanleitung

Siemens

Siemens MOMMOMAT 1000 Anleitungen und Rezepte

Siemens

Siemens Artis Q Bedienungsanleitung

Siemens

Siemens MAGNETOM Aera Bedienungsanleitung

Siemens

Siemens Servo Screen 390 Bedienungsanleitung

Siemens

Siemens VB 13C Bedienungsanleitung

Siemens

Siemens SIREMOBIL Compact Gebrauchsanweisung

Siemens

Siemens HearCheck Screener Bedienungsanleitung

Siemens

Siemens ARCADIS Varic Bedienungsanleitung

Siemens

Siemens Uroskop ACCESS Installationshandbuch

Siemens

Siemens MAGNETOM Skyra Bedienungsanleitung

Siemens

Siemens MAMMOMAT Novation DR Installationshandbuch

Siemens

Siemens SIREMOBIL Iso-C Betriebsanleitung

Siemens

Siemens SIREMOBIL Compact Betriebsanleitung

Siemens

Siemens 25 Bedienungsanleitung

Siemens

Siemens ARCOSKOP Bedienungs- und Wartungsanleitung

Siemens

Siemens MAMMOMAT 1000 Nova Bedienungs- und Wartungsanleitung

Siemens

Siemens SOMATOM Sensation 16 Bedienungsanleitung

Siemens

Siemens ACUSON S Series Bedienungsanleitung

Siemens

Siemens syngo MR E11 Bedienungsanleitung

Siemens

Siemens MAMMOMAT Nova Opdima 1000 Betriebsanleitung

Siemens

Siemens MAMMOMAT 3000 Einrichtungshandbuch

Siemens

Siemens ACUSON Cypress Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung