Siemens SITRANS LR Gebrauchsanweisung

Quick Start Manual 12/2012

SITRANS

Radar Transmitters

SITRANS Probe LR

IQ300IX.fm Page 5 Tuesday, October 2, 2001 1:43 PM

A5E32106153 SITRANS Probe LR – QUICK START MANUAL Page EN-1

mmmmm

English

SITRANS Probe LR Quick Start Manual

This manual outlines the essential features and functions of SITRANS Probe LR. We strongly

advise you to acquire the detailed version of the manual so you can use your instrument to its

fullest potential. The complete manual can be downloaded from the Siemens website at:

www.siemens.com/level. The printed manual is available from your local Siemens representative.

Questions about the contents of this manual can be directed to:

Siemens Milltronics Process Instruments

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario, Canada, K9J 7B1

Email: [email protected]om

MILLTRONICS is a registered trademark of Siemens Milltronics Process Instruments

Safety Guidelines1

Warning notices must be observed to ensure personal safety as well as that of others, and to

protect the product and the connected equipment. These warning notices are accompanied by

a clarification of the level of caution to be observed.

Process Instruments 2013.

Disclaimer of Liability

We encourage users to purchase

authorized bound manuals, or to view

electronic versions as designed and

authored by Siemens Milltronics Process

Instruments. Siemens Milltronics

Process Instruments will not be

responsible for the contents of partial or

whole reproductions of either bound or

electronic versions.

While we have verified the contents of this manual

for agreement with the instrumentation described,

variations remain possible. Thus we cannot

guarantee full agreement. The contents of this

manual are regularly reviewed and corrections are

included in subsequent editions. We welcome all

suggestions for improvement.

Technical data subject to change.

1. This symbol is used when there is no corresponding caution symbol on the product.

WARNING: relates to a caution symbol on the product, and means that failure to

observe the necessary precautions can result in death, serious injury, and/or

considerable material damage.

WARNING1: means that failure to observe the necessary precautions can result

in death, serious injury, and/or considerable material damage.

Note: means important information about the product or that part of the operating manual.

Page EN-2 SITRANS Probe LR – QUICK START MANUAL A5E32106153

mmmmm

English

SITRANS Probe LR

SITRANS Probe LR is a 2-wire loop-powered, continuous level measuring instrument that

utilizes advanced pulse radar technology at 5.8 GHz (6.3 GHz in North America). The instrument

consists of an electronic component coupled to the antenna and process connection.

Communication is via HART1, and signals are processed using Sonic Intelligence®.

Specifications

For a complete listing, see the full manual for SITRANS Probe LR (Part#: 7ML19985HR0x). For

Approvals information, please refer to the device nameplate.2

Ambient/Operating Temperature

WARNING: Changes or modifications not expressly approved by Siemens could void

the user’s authority to operate the equipment.

Notes:

• This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own expense.

• SITRANS Probe LR is to be used only in the manner outlined in this manual, otherwise

protection provided by the equipment may be impaired

• This product is intended for use in industrial areas. Operation of this equipment in a

residential area may cause interference to several frequency based communications..

1. HART®is a registered trademark of the HART Communication Foundation.

2. When the locking collar is secured, it prevents the enclosure rotating on the threaded connection.

Note: Process temperature and pressure capabilities are dependent upon information on

the process device tag. The reference drawing listed on the tag can be downloaded from the

Siemens website. Go to the SITRANS Probe LR product page at:

https://pia.khe.siemens.com/index.asp?Nr=11158.

process temperature

–40 to +80 °C (–40 to +176 °F)

ambient temperature

(surrounding enclosure volume)

–40 to +80 °C (–40 to +176 °F)

process device

tag

nameplate location

customer-supplied

flange

locking collar2over threaded connection;

secured by three 2 mm Allen set-screws

hand programmer

A5E32106153 SITRANS Probe LR – QUICK START MANUAL Page EN-3

mmmmm

English

Power

• Maximum 30 V DC

• 4 to 20 mA

Approvals

• General CSAUS/C, FM, CE, C-TICK

• Radio Europe (R&TTE), FCC, Industry Canada

• Hazardous Intrinsically Safe (Europe) ATEX II 1 G EEx ia IIC T4

(US/Canada) FM/CSA1: (barrier required)

Class I, Div. 1, Groups A, B, C, D

Class II, Div. 1, Groups E, F, G

Class III T4

(Australia) ANZEx Ex ia IIC T4

(Tamb = –40 to + 80 °C) IP67, IP68

(International) IECEx TSA 04.0020X Ex ia IIC T4

(Brazil) INMETRO: DNV 12.0068 X

Ex ia IIC T4 Ga

IP66/IP67/IP68

-40 ºC ≤T a ≤+80 ºC

DNV #OCP 0017

ABNT NBR IEC 60079-0:2008 e

ABNT NBR IEC 60079-11:2009

Non-incendive (US) FM2:

Class I, Div. 2, Groups A, B, C, D T5

• Marine Lloyd’s Register of Shipping

ABS Type Approval

Mechanical

• Process Connections:

threaded connection 1.5” NPT, BSP, or G (BS EN ISO 228-1)

•Antenna:

polypropylene rod hermetically sealed construction

Nominal 24 V DC at max. 550 Ohm

1. See

Wiring Drawing: Intrinsically Safe (FM )

on page 2 of Appendix A, for drawing number 23651611,

Wiring Drawing: Intrinsically Safe (CSA)

on page 3 of Appendix A, for drawing number 23651621.

2. See

Wiring Drawing: Non-incendive (FM)

on page 1 of Appendix A, for drawing number 23650537.

Note: The use of approved watertight conduit hubs/glands is required for Type 4X /

NEMA 4X, Type 6 / NEMA 6, IP67, IP68 (outdoor applications).

Note: EN61000-4-3 (CE EMC) testing was conducted on the SITRANS Probe LR while

mounted in a metallic vessel.

Page EN-4 SITRANS Probe LR – QUICK START MANUAL A5E32106153

mmmmm

English

Process

• Temperature (at process connection): 40 to +80 °C (40 to +176 °F)

• Pressure (vessel): maximum 3 bar, gauge (43.5 psi, gauge)

Installation

Mounting location

Recommendations

• Ensure ambient temperature is within –40 to +80 °C (–40 to +176 °F).

• Provide easy access for viewing the display and programming via the hand programmer.

• Ensure the environment is suitable to the housing rating and materials of construction.

Precautions

• Avoid proximity to high voltage or current wiring, high voltage or current contacts, and to

variable frequency motor speed controllers.

• Avoid interference to the emission cone from obstructions or from the fill path.

• Avoid central locations on vessels.

WARNINGS:

• This product can only function properly and safely if it is correctly transported,

stored, installed, set up, operated, and maintained.

• Never attempt to loosen, remove, or disassemble process connection or instrument

housing while vessel contents are under pressure.

• This product is designated as a Pressure Accessory per Directive 97 / 23 / EC, and is

not intended for use as a safety device.

• Materials of construction are chosen based on their chemical compatibility (or

inertness) for general purposes. For exposure to specific environments, check with

chemical compatibility charts before installing.

• The user is responsible for the selection of bolting and gasket materials which will

fall within the limits of the flange and its intended use, and which are suitable for

the service conditions.

• Improper installation may result in loss of process pressure.

preferred undesirable

Coni

Fl at

Flat ParabolicConical

min. 300 mm (1 ft) for every

3 m (10 ft) of vessel height

beam

angle

28o

• Locate the antenna away from the side wall, to

avoid interference from indirect echoes.

• Avoid interference from objects such as ladders

or pipes, which can cause false echoes.

• Avoid interference from the fill path.

A5E32106153 SITRANS Probe LR – QUICK START MANUAL Page EN-5

mmmmm

English

Mounting instructions

• Before inserting SITRANS Probe LR into its mounting connection, check to ensure the

threads are matching to avoid damaging them.

• Simply screw SITRANS Probe LR into the process connection, and hand tighten.

• For pressure applications, it will be necessary to use PTFE tape (or other appropriate

thread-sealing compound) and tighten the process connection beyond hand-tight.

The maximum torque is 40 N-m (30 ft-lbs).

• To rotate the enclosure, use a 2 mm Allen key to loosen the three set-screws that secure

the locking collar. Once the enclosure is positioned as desired, tighten the set-screws.

Wiring

Power1

WARNINGS:

DC terminals shall be supplied from an SELV 1source in accordance with IEC-

1010-1 Annex H.

All field wiring must have insulation suitable for rated voltages.

1. Safety Extra Low Voltage

minimum

100 mm (4")

minimum

10 mm (0.4")

To provide optimum signal conditions on a manhole cover, locate the antenna off-center

relative to the cover, typically 100 mm (4”) from the side of the manhole.

• Use the 100 mm (4") shield on nozzles that are 100 mm (4") in length, or shorter.

• Use the 250 mm (10") shield on nozzles that are 250 mm (10") in length, or shorter.

Mounting on a nozzleMounting on a manhole cover

Page EN-6 SITRANS Probe LR – QUICK START MANUAL A5E32106153

mmmmm

English

Connecting SITRANS Probe LR1

1. If you want to rotate the instrument on the process connection, use the 2 mm Allen

key provided to loosen the 3 Allen set-screws securing the locking collar. Position

the unit, and retighten the screws.

2. Strip the cable jacket for approximately 70 mm (2.75") from the end of the cable, and

thread the wires through the strain relief2.

Notes:

• For detailed wiring instructions, please refer to the full Instruction Manual.

• Use shielded, twisted pair cable (wire gauge AWG14 to AWG22).

• Separate cables and conduits1may be required to conform to standard instrumentation

wiring practices, or electrical codes.

• The non-metallic enclosure does not provide a continuous ground path between conduit

connections: use grounding type bushings and jumpers.

1. If cable is routed through conduit, use only approved suitable-size hubs for waterproof application.

Note: Do not rotate the enclosure after programming and vessel calibration,

otherwise an error may occur, caused by a polarity shift of the transmit pulse.

2. If cable is routed through conduit, use only approved suitable-size hubs for waterproof applications.

locking collar

terminal block

lid screw (1 of 2)

Unscrew the two lid screws to release the

hinged lid and access the terminal block.

strain

relief (or

NPT cable

entry)

A5E32106153 SITRANS Probe LR – QUICK START MANUAL Page EN-7

mmmmm

English

3. Connect the wires to the terminals: the polarity is identified

on the terminal block.

4. Tighten the gland to form a good seal.

Close the lid and tighten screws: please do not overtighten

screws. (Recommended torque is 1.1 to 1.7 N-m (10 to 15 in-lb)

of torque)

RUN Mode and PROGRAM Mode

SITRANS Probe LR has two modes of operation: RUN and PROGRAM.

After you complete the installation procedures and power up SITRANS Probe LR, it starts in

RUN mode and detects the material level. It returns the distance (in meters) to the material

level referenced from Empty (process empty level). This is the default start-up display mode.

RUN Mode Display

Use the hand programmer to control the display.

If the echo confidence drops below the echo confidence threshold, the failsafe timer starts

running. When the timer expires, the letters LOE (Loss of Echo) alternate with the reading

every two seconds, and the Reliable Echo indicator is replaced by the Unreliable indicator.

When a valid reading is received, the level reading display returns to normal operation.

1 – Primary Reading (displays level, distance, or volume, in either units or percent)

2 – Secondary Reading (displays Parameter number for Auxiliary Reading)

3 – Echo status indicator: Reliable Echo or Unreliable Echo

4 – Units or Percent

5 – Active bar graph represents material level

6 – Auxiliary Reading (depending on the parameter selected, it displays milliAmp value,

distance, or echo confidence, with units where applicable)

Normal operation Failsafe operation

Page EN-8 SITRANS Probe LR – QUICK START MANUAL A5E32106153

mmmmm

English

PROGRAM Mode Display

Programming

• Set parameters to suit your specific application.

•ActivatePROGRAM mode at any time, to change parameter values and set operating

conditions.

• For local programming, use the Siemens hand programmer.

• For programming from a distance, use either a PC running SIMATIC1PDM or a HART

handheld communicator.

Hand programmer.

Note: Do not use the handheld programmer at the same time as SIMATIC PDM, or erratic

operation may result.

1. SIMATIC® is a registered trademark of Siemens AG.

1 – Primary Reading (displays parameter value)

2 – Secondary Reading (displays parameter number)

3 – Programming indicator

6 – Auxiliary Reading (displays parameter names for P001 to

P010, if a language is selected. It displays the index value

for indexed parameters, such as P054)

display

hand-held programmer

max. 600 mm

(2 ft)

Key Programming Mode

to Values

Decimal point

Negative value

CLEAR value

TOGGLE between Units and % on parameter

value

End PROGRAM session and enable RUN mode

Update echo quality parameters

Parameter scroll-up

Parameter scroll-down

DISPLAY opens parameter fields

ENTER the displayed value

For direct access to SITRANS Probe LR,

point the programmer at the

SITRANS Probe LR display and press

the keys. (For detailed instructions, see

the next page.)

Inhaltsverzeichnis

Sprachen:

Andere Siemens Sender Handbücher

Siemens

Siemens SINAMICS G120 Bedienungsanleitung

Siemens

Siemens SITRANS T Series Administratorhandbuch

Siemens

Siemens SITRANS P Administratorhandbuch

Siemens

Siemens sitrans PROBE LU Gebrauchsanweisung

Siemens

Siemens Sitrans LR200 Gebrauchsanweisung

Siemens

Siemens SITRANS P500 Administratorhandbuch

Siemens

Siemens SITRANS P DS III Bedienungsanleitung

Siemens

Siemens SITRANS P 7MF4013 Bedienungsanleitung

Siemens

Siemens SITRANS L Series Bedienungsanleitung

Siemens

Siemens 7MF8*24 Series Administratorhandbuch

Siemens

Siemens SITRANS L Bedienungsanleitung

Siemens

Siemens SITRANS P250 Bedienungsanleitung

Siemens

Siemens sitrans tr200 Bedienungsanleitung

Siemens

Siemens SITRANS LR260 Bedienungsanleitung

Siemens

Siemens SITRANS LR560 Gebrauchsanweisung

Siemens

Siemens Sitrans LR200 Gebrauchsanweisung

Siemens

Siemens SITRANS LR250 PROFIBUS PA Bedienungsanleitung

Siemens

Siemens SITRANS L Bedienungsanleitung

Siemens

Siemens 7MF03 Series Administratorhandbuch

Siemens

Siemens 7MF4033 series Bedienungsanleitung

Siemens

Siemens SITRANS LR560 Bedienungsanleitung

Siemens

Siemens SITRANS F M Intermag 2 Bedienungsanleitung

Siemens

Siemens SITRANS P500 Administratorhandbuch

Siemens

Siemens Sitrans LR200 Gebrauchsanweisung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung