SIIG JU-P40412-S1 Bedienungsanleitung
1
04-0801B
4-Port USB 3.0 PCIe
Installation Guide
Introduction
The 4-Port USB 3.0 PCIe adds four USB 3.0 ports
to your PCIe-enabled desktop PC, enhancing
existing systems with the latest USB 3.0
technology.
Key Features and Benefits
• Compliant with Universal Serial Bus 3.0
Specification
• Compliant with PCI Express Base
Specification, Revision 2.0
• Supports data rate up to 5Gb/s and
backward compatible with USB 2.0/1.1
devices
Package Contents
• 4-Port USB 3.0 PCIe
• Driver CD
• Installation guide
2
Figure 1: Layout
*Note: The host adapter will work with or
without the power connected. However,
we recommend this connection if your
USB devices are not recognized, lose
connection to Windows randomly or all
ports are connected to USB devices.
System Requirements
• Desktop PC with an available PCIe slot
• Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
Layout
SATA power connector
(optional)*
USB 3.0 ports
3
Hardware Installation
Since the design of computer cases and
motherboards vary, refer to your computer’s
reference manual for further information.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord from the computer.
3. Remove your computer cover.
4. Remove the slot bracket from an available
PCIe slot.
5. Carefully align the card's bus connector
with the selected PCI Express slot on the
motherboard. Push the card down firmly,
but gently, until it is well seated.
6. Replace the slot bracket holding screw to
secure the card.
4
7. Connect the system power supply to the
cards's SATA power connector. This
connection is optional. Please see Layout
on page 2 for more information.
8. Replace the computer cover and reconnect
the power cord.
Driver Installation
Note: For Windows 8, the driver is already
embedded in the operating system. So no
additional installation steps are needed.
Windows 7 (32-/64-bit) / Vista (32-/64-bit) /
2008 R2
1. Install the card and boot up Windows.
2. For Windows Vista, click Cancel at the
Found New Hardware.
For other OS, go directly to step 3.
3. Insert the driver CD.
For Windows 7 / 2008 R2: At the CD AutoPlay
box, click Open folder to view files, then
double click Setup.
5
For Windows Vista: At the CD Autoplay
window, double click Setup.
4. Click Yes or Continue at the User Account
Control. For 2008 R2, skip this step.
5. At Welcome to InstallShield wizard..., click
Next.
6. Select I accept the terms of the license
agreement, click Next.
7. At ReadytoInstalltheProgram,clickInstall.
8. Click Finish, then restart the computer.
Windows XP (32-/64-bit) / Server 2008 &
2003 (32-/64-bit)
1. Install the card and boot up Windows.
2. Click Cancel at the Found New Hardware
window.
3. Insert the driver CD. Click Start, Run. Type
D:\Setup.exe, click OK. (Change D: to
match your CD\DVD-ROM drive letter)
4. At Welcome to InstallShield wizard..., click
Next.
5. Select I accept the terms of the license
agreement, click Next.
6
6. At ReadytoInstalltheProgram,clickInstall.
7. Click Finish, then restart the computer.
To Verify Successful Installation
1. Go to Device Manager to verify installation.
For Windows 8 / Windows 7/ Windows XP /
Server 2008 R2 / Server 2003: Right click
Computer or My Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows 2008: Right click Computer,
click Manage, double click Diagnostics,
then click Device Manager.
2. Double click Universal Serial Bus
controllers. A Renesas Electronics USB
3.0 Host Controller and a Renesas
Electronics USB 3.0 Root Hub should be
displayed.
For Windows 8, a Renesas USB 3.0
eXtensible Host Controller is displayed.
7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analysts will promptly
respond.
SIIG offers a lifetime manufacturer warranty with this product. This warranty covers
the original purchaser and guarantees the product to be free of any defects in materials
or workmanship for the life of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then Request A Product Replacement to
submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request
will be processed, if the product is determined to be defective, an RMA number will
be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.
PRODUCTNAME
4-Port USB 3.0 PCIe
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
4-Port USB 3.0 PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft
Corporation. All other names used in this publication are for identification only and may be
trademarks of their respective owners.
August, 2014 Copyright © 2014 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebooksystemsand externalperipherals. SIIGcontinues togrowby adding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIGproductsoffer comprehensiveuser manuals,manyuser-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
throughmajordistributors, system integrators,and VARs inthe Americas and
the UK, and through e-commerce sites.
Inhaltsverzeichnis
Andere SIIG Computerhardware Handbücher
SIIG
SIIG 1-Port ECP Bedienungsanleitung
SIIG
SIIG SIIG 2-Port Serial 950-Value Bedienungsanleitung
SIIG
SIIG USB 2.0 9-in-1 Bay R/W Bedienungsanleitung
SIIG
SIIG FireWire Home DV Kit Bedienungsanleitung
SIIG
SIIG Silent Mini Notebook Cooler Bedienungsanleitung
SIIG
SIIG Network Device EVTEK-5103 Installationsanleitung
SIIG
SIIG NN-EC2822-S1 Bedienungsanleitung
SIIG
SIIG ExpressCard 11-in-1 Reader/Writer Bedienungsanleitung
SIIG
SIIG USB 2.0+1394 DV Kit Bedienungsanleitung
SIIG
SIIG JU-2NE012 Bedienungsanleitung
SIIG
SIIG Serial ATA PCI Bedienungsanleitung
SIIG
SIIG CyberSerial ExpressCard Bedienungsanleitung
SIIG
SIIG FireWire Dual-Port CardBus Bedienungsanleitung
SIIG
SIIG CyberParallel Dual Bedienungsanleitung
SIIG
SIIG JU-P40311-S1 Bedienungsanleitung
SIIG
SIIG Dual Profile Hi-Speed USB 4-Port PCI Bedienungsanleitung
SIIG
SIIG UltraATA 133 PCI Bedienungsanleitung
SIIG
SIIG SC-SAE512-S1 Bedienungsanleitung
SIIG
SIIG SATA II-150 PCI Bedienungsanleitung
SIIG
SIIG Hi-Speed ExpressCard CF R/W Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
