SIIG AV-GM07P3-S1 Bedienungsanleitung

4x4 HDMI Deep Color & full 3D over single Cat.X

Matrix

To avoid EMI issue, complete STP Cat6 cable is strongly recommended!

P/N: AV-GM07P3-S1

Safety and Notice

The AV-GM07P3-S1 4x4 HDMI Deep Color & full 3D over single Cat.X matrix has been

tested for conformance to safety regulations and requirements, and has been certified

for international use. However, like all electronic equipments, the AV-GM07P3-S1

should be used with care. Please read and follow the safety instructions to protect

yourself from possible injury and to minimize the risk of damage to the unit.

●Follow all instructions and warnings marked on this unit.

●Do not attempt to service this unit yourself, except where explained in this manual.

●Provide proper ventilation and air circulation and do not use near water.

●Keep objects that might damage the device and assure that the placement of this

unit is on a stable surface.

●Use only the power adapters and power cords and connection cables designed for

this unit.

●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to

the device before cleaning.

TABLE OF CONTENTS

INTRODUCTION.................................................................................................................1

FEATURES.........................................................................................................................1

PACKAGE CONTENTS......................................................................................................1

SPECIFICATIONS..............................................................................................................2

PANEL DESCRIPTIONS.....................................................................................................3

Transmitting unit ► ................................................................................................3

Receiving unit ►....................................................................................................4

HARDWARE INSTALLATION.............................................................................................4

IR PASS-THROUGH...........................................................................................................6

CONNECTION DIAGRAM ..................................................................................................7

OPERATION APPROACH..................................................................................................8

EDID LEARNING..............................................................................................................22

WARRANTY .....................................................................................................................23

INTRODUCTION.................................................................................................................1

FEATURES.........................................................................................................................1

PACKAGE CONTENTS......................................................................................................1

INTRODUCTION

The AV-GM07P3-S1 4x4 HDMI Deep Color & full 3D over single Cat.X matrix provides the most

flexible and cost effective solution in the market to route high definition video sources plus

multi-channel (up to 7.1-channel) digital audio from any of the four HDMI sources to the remote

displays at the same time. Through only one low cost Cat-5/5e/6 LAN cable, not only high quality

video and audio can be transmitted to the display sites, but also users can switch among four HDMI

sources using the push-in button or remote control. Furthermore, the built-in IR extension function

makes users at display site access the DVD player, PS3 or any HDMI supported devices directly!

FEATURES

●Supports HDMI Deep Color & full 3D

●HDCP compliant

●Allows any source to be displayed on multiple displays at the same time

●Allows any HDMI display to view any HDMI source at any time

●Supports 7.1 channel digital audio

●Supports default HDMI EDID and learns the EDID of displays

●The matrix master can switch every output channels to any HDMI inputs by push-in button, IR

remote control, RS-232 control, and Ethernet control

●Allow controlling local HDMI sources such as DVD and TiVo by attached IR extender from remote

receiver to matrix master

●Extends video signal up to 35m (115 feet) over single CAT.X at 1080p and likely longer with better

HDMI source device (such as PS3), better grade HDMI display (such as Sony X-series HDTV), and

better quality solid CAT6 cable

●Easy installation with rack-mounting and wall-mounting designs for master and receiver

respectively

●Fast response time –2~5 seconds for channel switch

PACKAGE CONTENTS

●1x AV-GM07P3-S1 ●4x AV-GM07P3-S1-RX

●5x IR receiver ●1x IR blaster*

●1x DC 12V 5A ●4x DC 5V 2A

●1x Rack-mounting ear set ●1x IR Remote control*

●1x Installation software CD ●1x User Manual

SPECIFICATIONS

Model Name

AV-GM07P3-S1

Technical

AV-GM07P3-S1

AV-GM07P3-S1-RX

Role of usage

True 4x4 matrix switcher

Transmitter [TX]

Receiver [RX]

HDMI compliance

HDMI Deep Color & full 3D

HDCP compliance

Yes

Video bandwidth

Single-link 225MHz [6.75Gbps]

Video support

480i / 480p / 720p / 1080i / 1080p60 36-bit color

Audio support

Surround sound (up to 7.1ch) or stereo digital audio

HDMI over CAT5

transmission range

Full HD (1080p): 35m (115ft) [CAT.X]

HD (720p/1080i): 50m (165ft) [CAT.X]

HDMI equalization

N/A

8-level digital rotary control

Input TMDS signal

1.2 Volts [peak-to-peak]

Input DDC signal

5 Volts [peak-to-peak, TTL]

ESD protection

Human body model —±15kV [air-gap discharge] & ±8kV [contact discharge]

PCB stack-up

4-layer board [impedance control —differential 100Ω; single 50Ω]

Input

4x HDMI / 1x RS-232 / 1x Ethernet

5x IR socket for IR receiver

1x RJ-45 /

1x IR socket for IR receiver

Output

4x RJ-45 /

5x IR socket for IR blaster

1x HDMI /

1x IR socket for IR blaster

HDMI Input selection

Push-in button / IR remote control /

RS-232 control / Ethernet control

IR remote control

HDMI source control

Controllable via IR pass-through from IR receiver at RX to IR blaster at TX

IR remote control

Electro-optical characteristics: = 25° / Carrier frequency: 20-60kHz

HDMI connector

Type A [19-pin female]

RJ-45 connector

WE/SS 8P8C

RS-232 connector

DE-9 [9-pin D-sub female]

3.5mm connector

Earphone jack for IR blaster

[All IR Out] IR control on all source devices

[IR1~IR4] IR control on individual source

device

Earphone jack for IR receiver

[System IR] Receives IR commands from

remote control

Earphone jack for IR receiver

[IR] Receives IR commands

from remote control

Mechanical

AV-GM07P3-S1

AV-GM07P3-S1-RX

Enclosure

Metal case

Dimensions

(L x W x H)

Model

440 x 146 x 44mm [17.3" x 5.7" x

1.7"]

91 x 75 x 24mm [3.6" x 2.9" x 9.4"]

Package

521 x 265 x 182mm [20.5" x 10.4" x 7.2"]

Carton

542 x 411 x 300mm [21.3" x 16.2" x 11.8"]

Weight

Model

1322g [46.6oz]

239g [8.4oz]

Package

3250g [7.2 lbs]

Fixedness

1RU rack-mount with ears

Wall hanging holes

Wall-mount with screws

* Additional IR remote controllers and IR blasters can be purchased as optional accessories to

control the HDMI sources located separately.

Power supply

12V 5A DC

5V 2A DC

Power consumption

20 Watts [max]

1 Watt [max]

Operation

temperature

0~40°C [32~104°F]

Storage temperature

-20~60°C [-4~140°F]

Relative humidity

20~90% RH [no condensation]

PANEL DESCRIPTIONS

Transmitting unit ►AV-GM07P3-S1

Front Panel

1. Source Status: Input source indicator LED

2. IR SENSOR: IR sensor for receiving the IR commands from IR remote

3. Output Push Button & 7-segment LED: Front panel push buttons used to select the number of

display channel & LED display for output ports

4. Input Push Button & 7-segment LED: Front panel push buttons used to select the number of

input source & LED display for input channels

Rear Panel

5. HDMI Local Loopout Port 1-4: Local loopout HDMI outputs for each output channel

6. Output Port 1-4: RJ-45 outputs for each output channel

7. INPUT 1-4: HDMI inputs

8. IR Receiver 1-4: Infrared 3.5mm socket for plugging in the extension cable of IR receiver

9. System IR Receiver: Ext. IR receiver

10. IR Blaster 1-4: 3.5mm IR blaster socket for individual HDMI source control

11. All IR Output: 3.5mm IR blaster socket for HDMI source control on all 4 inputs

12. RS-232: RS-232 control port

13. Ethernet: Ethernet control port

14. +12V DC: 12V DC power jack

Receiving unit ►AV-GM07P3-S1-RX

Front Panel

Rear Panel

1. +5V DC: Connect to 5V DC power supply

2. HDMI Output: Connect to a HDMI display with a HDMI male-male cable

3. Signal Level: Adjust the 8-level equalization control to the received HDMI signals. The HDMI

signal level varies from MAX (strongest) to MIN (weakest) for respective transmission length

from longest possible range to short distance. Adjust the signal level from MIN to MAX until

desired video quality is displayed. Inappropriate signal level setting may cause overpowering

issue that would shorten the product life significantly!

4. HDMI Signal In: Plug in a Cat-5/5e/6 cable that needs to be linked to the receiving unit

5. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster

6. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver

HARDWARE INSTALLATION

1. Connect all sources to HDMI Inputs on the 4x4 HDMI over CAT.X matrix master AV-GM07P3-S1.

2. Connect each CAT.X output port on the AV-GM07P3-S1 to respective CAT.X input on the remote

receiver AV-GM07P3-S1-RX.

3. Connect each HDMI output on receiver to HDMI displays.

4. Connect IR blaster to the AV-GM07P3-S1 and direct the IR blaster to point towards the built-in IR

receiver of the HDMI source devices.

5. Connect the +12V 5A DC power supply to the AV-GM07P3-S1 and +5V 2A DC power supply to the

receivers

6. Power on all HDMI sources and displays.

7. Dial the 8-level rotary control switch to adjust the HDMI signal level until the picture and sound

are clear. It is recommended to dial from weakest to strongest to find the optimal visual

experience

IR PASS-THROUGH

IR Extenders

IR Blaster

IR Receiver

IR Sockets

AV-GM07P3-S1

All IR Out: The default location for IR blaster to transmit all IR command signals received from any

of the four remote receivers to all of the HDMI sources.

IR BLASTER 1-4: IR blaster connected here can only transmit IR command signals from the remote

receivers that are setting at respective input channel from 1 to 4.

System IR: Receives IR commands from remote control

AV-GM07P3-S1-RX

IR BLASTER: IR control on individual display device

IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote

controls of AV-GM07P3-S1 and all other HDMI source devices.

Definition of IR Earphone Jack

IR Blaster

IR Receiver

Incorrect placement of IR Blaster and Receiver may result in the failure of the IR

extenders. Please check carefully before plugging in the IR extender to the

respective IR sockets. Warranty will not cover the damage.

CAUTION!

CONNECTION DIAGRAM

You can buy any IR extension cables in the market that are compatible to the definition of

the IR sockets for the matrix if necessary for replacement use. However, IR cables longer

than 2m (6-ft) may not work.

OPERATION APPROACH

Method A: Push-in Button

1. IN/OUT MAP

1) Use the “+”or “-“ output push button to select the number of display

2) Use the “+”or “-“ input push button to select the number of input source

“+”: change selected input/output port in ascending order

“-” : change selected input/output port in descending order

After you select the desired input/output port, the LED will blink twice and the setting will be

effective

2. Save Mapping Mode

1) Keep pushing “output+ (save)”button until the output LED shows “d.” to enter the Save

Mapping Mode.

2) Use the “+”or “-“ input push button to select the mapping configuration (1~8) which you want to

save current input/output mapping

3) After you select the desired mapping configuration number, the LED will blink twice and the

mapping setting will be saved

4) If you push the “output- (preset)”button before the mapping setting is saved, the LED will show

“一”“一”to quit the Save Mapping Mode

3. Preset Mapping Mode

1) Keep pushing “output- (preset)”button until the output LED shows “P.” to enter the Preset

Mapping Mode.

2) Use the “+”or “-“ input push button to select the saved mapping configuration (1~8) which you

want to recall

3) After you select the desired mapping configuration number, the LED will blink twice and the

mapping setting will be effective

default

learn

preset

save

Inhaltsverzeichnis

Andere SIIG Matrix-Umschalter Handbücher

SIIG

SIIG AV-GM07U3-S1-V2 Bedienungsanleitung

SIIG

SIIG AV-GM07M3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0823-S1 Bedienungsanleitung

SIIG

SIIG AV-GM06Y3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07U3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM06X3-S1 Bedienungsanleitung

SIIG

SIIG 4x2 HDMI Bedienungsanleitung

SIIG

SIIG AV-GM08F3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM08G3-S1 Bedienungsanleitung

SIIG

SIIG CE-H27Q11-S1 Bedienungsanleitung

SIIG

SIIG CE-H23H11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0843-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0733-S1 Bedienungsanleitung

SIIG

SIIG MA-1088D Bedienungsanleitung

SIIG

SIIG CE-H24W11-S1 Bedienungsanleitung

SIIG

SIIG CE-H21F11-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07A3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0783-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07N3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07L3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07X3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0803-S1 Bedienungsanleitung

SIIG

SIIG AV-GM07J3-S1 Bedienungsanleitung

SIIG

SIIG AV-GM0703-S1 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Kramer

Kramer VS-66H Bedienungsanleitung