SIIG Low Profile PCI-2S Bedienungsanleitung
1
Low Profile PCI-2S
Quick Installation Guide
04-0367B
Introducing the Low Profile PCI-2S
The Low Profile PCI-2S high-speed serial card provides
two additional 9-pin serial ports.
FeaturesandBenefits
•Conforms to PCI v2.2 Plug and Play
•Full support for Windows-based software
•Supports 32-/64-bit, 3.3V/5V PCI and PCI-X slots
•Two high-speed 16550 UART serial ports (9-pin)
supports data rate up to 230 Kbps
•Built-in 32-byte FIFO buffer dramatically increase
data transmit/receive speed, especially under
Windows' multitasking environment
•Each serial port can be configured for either 5V or
12V, for serial devices that require power
SystemRequirements
•Pentium®orequivalentcomputerwithanavailable
PCI slot
•Windows®95/98/98SE/ME/NT 4.0/2000/XP (32-
/64-bit)/Server2003(32-/64-bit)/Vista(32-/64-bit)
PackageContents
•Low Profile PCI-2S board
• Connectorbracketwith9-pinserialport(forthe2nd
serial port)
• DriverCD
• This quick installation guide
2
Layout
Figure 1. Layout
JumperSettings(JP1,JP2)
Open = 0 volts (default)
Short 1-2 = 5V @ pin 9
Short 2-3 = 12V @ pin 9
Note: Mostserial devices donot require additional
power through the serial port. Consult your serial
device'smanualformoreinformation. Thejumpers
may be placed onto one pin to prevent loss.
Serial port 1 JP1 (serial port 1)
JP2 (serial port 2)
Pin header for
serial port 2
Pin1
Connector bracket with
9-pin serial port
Stripe
Pin 9
Figure 2. Pin 9
Pin 9
3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the computer and
remove the cover.
3. Remove the slot bracket from an available PCI slot.
4. Set JP1 and/or JP2 jumper settings to the desired
voltage only if your serial device needs additional
power from the serial port. However, most serial
devices do not require additional power. For more
information see Jumper Settings on page 2.
5. Plug-in the Connector bracket with 9-pin serial
port to Pin header for serial port 2. Position the
stripe on the ribbon cable to point to silkscreened
pin 1. See Layout on page 2for proper connection.
Skip this step if only one serial port is needed.
6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket holding screw to secure the
card.
4
8. Remove the slot bracket from an available PCI slot,
thensecuretheSerialportcablewiththeslotbracket
holding screw. Skip this step if the second serial port is
not needed.
9. Replacethecomputercoverandreconnectthepower
cord.
Software Installation
This section provides information on how to install the
Low Profile PCI-2S drivers.
Windows95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, and click Other Locations.
TypeinD:\9x,clickOK,thenFinish. (ChangeD:to
match your CD-ROM drive letter)
3. From the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in
D:\9x, then click OK.
4. Restart Windows to complete the installation.
Windows98/98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommended), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\9x, then click
Next. (Change D: to match your CD-ROM drive
letter)
4. Click Next, then Finish.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.
5
WindowsME
1. AttheAddNewHardwareWizard,chooseSpecify
the location of the driver (Advanced), then click
Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\ME, then click
Next. (Change D: to match your CD-ROM drive
letter)
3. Click Next, then Finish.
4. Repeat steps 1and 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
ToVerifyWindows95/98/98SE/MEInstallation
1. Right click My Computer, click Properties,then
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerialPCI
16Cxxx... should be displayed two times.
3. Double click Multi-function adapters, SIIG
CyberPro 2S PCI board and PCI Function should
be displayed.
WindowsNT4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_serial.exe, then click OK.
(Change D: to match your CD-ROM drive letter)
3. At the Welcome window, click Next.
4. Choose Install, then click Next.
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.
6
ToVerifyWindowsNT 4.0Installation
1. Click Start,Settings,Control Panel,double click
Ports icon.
2. Two new COM ports will be assigned.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), and click Next.
3. Check Specifyalocation, uncheckthe other boxes,
and click Next.
4. InsertthedriverCD,typeinD:\2000,thenclickOK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
WindowsXP/Server2003(32-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
ForXPw/SP2orlater/Server2003wSP1orlater:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended),then click Next.
3. Click Finish.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
7
WindowsXP/Server2003(64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
ForXPw/SP2 or later/Server 2003 wSP1orlater:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended),then click Next.
3. Click Continue Anyway, then click Finish.
4. Repeat steps 1-3 several more times.
5. Restart Windows to complete the installation.
To Verify Windows 2000/XP/Server 2003 Installation
1. Right click My Computer, click Manage, then click
Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial PCI 16Cxxx... should be
displayed two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S PCI board should be displayed.
WindowsVista™
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.
3. Repeat step #2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.
8
ToVerifyWindowsVistaInstallation
1. Rightclick Computer,clickManage,clickContinue,
then click Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S PCI board should be displayed.
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows95/98/98SE/ME
1. From the Device Manager window double click
Ports (COM & LPT), double click the CyberSerial
PCI serial port you want to change.
2. ClickSettingstab,clickthedownarrownexttoPort
Name box and select a COM port that is not in use.
Click OK.
3. Click OK, then close Device Manager.
Windows2000/XP/Server2003/Vista
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab and click Advanced.
3. ClickthedownarrownexttotheCOMPortnumber
box and select a COM port that is not in use. Click
OK.
4. Click OK, then close Device Manager.
9
Blank Page
10
Blank Page
Inhaltsverzeichnis
Andere SIIG PCI-Karte Handbücher
SIIG
SIIG JJ-P00112-S6 Bedienungsanleitung
SIIG
SIIG SC-SAE012-S2 Bedienungsanleitung
SIIG
SIIG NN-E38012-S2 Bedienungsanleitung
SIIG
SIIG SoundWave 7.1 PCI Bedienungsanleitung
SIIG
SIIG NN-83M012-S2 Bedienungsanleitung
SIIG
SIIG CyberPro PCI 2S Bedienungsanleitung
SIIG
SIIG CyberSerial Dual PCIe Bedienungsanleitung
SIIG
SIIG DP 4-Port USB 3.0 PCIe i/e Bedienungsanleitung
SIIG
SIIG CyberSerial Dual PCIe Bedienungsanleitung
SIIG
SIIG SIIG 2S1P Combo-Value Bedienungsanleitung
SIIG
SIIG VV-CV0012-S1 Bedienungsanleitung
SIIG
SIIG SoundWave 128 PCI Bedienungsanleitung
SIIG
SIIG CyberSerial Dual PCI Montageanleitung
SIIG
SIIG Serial ATA 4-Channel PCI Bedienungsanleitung
SIIG
SIIG SIIG 2S1P Combo-Value Bedienungsanleitung
SIIG
SIIG DP FireWire 800 PCI-32T Bedienungsanleitung
SIIG
SIIG SC-SA0012-S1 Bedienungsanleitung
SIIG
SIIG UltraATA 133 PCI Bedienungsanleitung
SIIG
SIIG SC-SAE412-S3 Bedienungsanleitung
SIIG
SIIG JJ-P02012 Bedienungsanleitung
Beliebte PCI-Karte Handbücher anderer Marken
ERMA
ERMA SSI 1417 Bedienungsanleitung
Moxa Technologies
Moxa Technologies CP-102E Bedienungsanleitung
I-Bus
I-Bus IBC2602 Bedienungsanleitung
Exsys
Exsys EX-60102 Bedienungsanleitung
Chelsio Communications
Chelsio Communications T5 Series Bedienungsanleitung
Conrad Electronic
Conrad Electronic 97 46 71 Bedienungsanleitung
ADLINK Technology
ADLINK Technology cPCI-3548 Bedienungsanleitung
Digium
Digium TE200 Series Bedienungsanleitung
Allo.com
Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung
Western Digital
Western Digital FireWire PCI Adapter Bedienungsanleitung
Pyle
Pyle Gamelink PLINK1 Bedienungsanleitung
Alpha Networks
Alpha Networks WMP-A13V Bedienungsanleitung