Simplicity Freedom S10S Bedienungsanleitung

(The chances are you’re

never going to read me)

Owner’s Manual

www.SimplicityVac.com

Models: S10S, S10D S10P, S10SAND

Contents

Getting Started

Important Safety Instructions 2

Polarization Instructions 3

State of California Proposition 65 Warnings 3

Description of the Vacuum 4

Assembling the Vacuum 5

Operation

Reclining the Handle 6

On/Off Switch 6

Edge Cleaning 6

Automatic Carpet Height Adjustment 6

Bare Floor Cleaning 6

Maintenance and Care

Power Cord Care 7

Vacuuming Under Furniture 7

Replacing the Vacuum Bag 8

Removing/Reinstalling the Bottom Plate 9

Replacing the Agitator Belt 10

Lifetime Belt Protection 10

Brushroll Jam Indicator 11

Resetting the Circuit Breaker 12

Replacing the Squeegee 12

Annual Checkup 12

Problem Solving Guide

Troubleshooting 13

Visit Simplicity Vacuums Online 13

How to Contact Your Authorized Retailer 13

Key Replacement Parts 13

For Best Performance 13

Warranty 14

IMPoRtAnt sAFetY InstRUCtIons

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

The manufacturer cannot accept responsibility for damage

caused when the appliance is not used according to the

instructions, or for uses other than those for which it

was intended.

To reduce the risk of fire, electric shock or injury:

sAVe tHese InstRUCtIons.

IMPoRtAnt:

• Do not leave appliance when plugged in.

Unplug from outlet when not in use and

before servicing.

• Do not use outdoors or on wet surfaces.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Use only as described in this manual.

• Do not use with damaged cord or plug.

If appliance is not working as it should,

has been dropped, damaged, left

outdoors, or dropped into water, return

it to your Authorized Simplicity Retailer

for service.

• Do not pull or carry by cord, use cord as

a handle, close a door on the cord, or pull

cord around sharp edges or corners. Do

not run appliance over cord. Keep cord

away from heated surfaces.

• Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with

wet hands.

• Do not put any object into openings. Do

not use with any opening blocked; keep

free of dust, lint, hair and anything that may

reduce air flow.

• Keep hair, loose clothing, fingers and all

parts of body away from openings and

moving parts.

• Do not pick up anything that is burning or

smoking, such as cigarettes, matches or

hot ashes.

• Do not use without vacuum bag in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or

combustible liquids such as gasoline or

use in areas where they may be present.

• Do not attempt to service the unit while

appliance is plugged in.

PoLARIZAtIon InstRUCtIons

Power Cord, 2-Wire Polarized Cord

To reduce the risk of electric shock, this product is equipped with a polarized alternating

current line plug (a plug having one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you are unable to insert the plug fully

into the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified

electrician to replace the obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to

cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to

cause birth defects or other reproductive harm.

DesCRIPtIon oF tHe VACUUM

1 Ergonomic Handle

2 On/Off Power Switch

3 Bag Compartment

4 Vacuum Nozzle

5 Headlight

6 Furniture Guard

7 Brushroll Jam Indicator (models S10P and S10SAND only)

8 Circuit Breaker Reset Button (models S10S and S10D only)

9 Handle Release Pedal

10 Quick Release Cord Hook

11 Upper Cord Hook

AsseMbLIng tHe VACUUM

Attaching the Handle to the Vacuum

NOTE: Do not plug in the vacuum until it is

completely assembled.

The vacuum cleaner and the handle are

packed separately and require assembly.

• Thread the cord through the lower and upper

cord guides on the back of the vacuum

bag (Fig. 1).

• Remove the handle bracket by removing the

two screws (Fig. 2).

• Place handle onto the back of the vacuum,

aligning holes with pegs (Fig. 3).

• Place the handle bracket back into position (Fig. 4).

• Secure with two screws removed in Step 2.

• Open the bag compartment to ensure a

vacuum bag is in place.

• Your vacuum is now ready for use.

• If storing the vacuum, wrap the cord clockwise

around the top and bottom cord hooks. Fasten

the plug to the wrapped cord using the channel

on the plug.

Unwinding the Power Cord

• The lower cord hook rotates to allow for

quick access to the power cord. Turn the

lower cord hook upward and you can quickly

drop the power cord to the floor without

unwinding it from the cord hooks.

• When storing the vacuum cleaner, turn the lower

cord hook to the downward position and wind the

power cord around the cord storage hooks.

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

± .02

± .01

° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

12345678

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

± .02

± .01

° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

12345678

Fig. 2

Fig. 3 Fig. 4

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESSOTHERWISE SPECIFIED

DESCRIPTION

DRAWINGSIZE:D

PARTNUMBER

SHEET 1 OF 1

X.X ± .02 IN RADII X.X ± .02

X.XX ± .01IN X,XX ± .01

X.XXX ± .005IN MACHINESURFACE

X.XXXX ± .0005 IN BREAK SHARP CORNERS TO .010 MAX

± 0 ° 30" COMMON TOBECONCETRIC TO .002

TACONYCORPORATION CLAIMS PROPRIETARY

RIGHTSIN THE MATERIAL DISCLOSED HERE IN.

THISDRAWING IS ISSUED FOR ENGINEERING

INFORMATIONONLY. ITMAY NOT BE REPRO-

DUCED,NOR MAY THE INFORMATION HERE IN

BEUSED FOR MANUFACTURING PURPOSES

WITHOUTWRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

TACONY CORPORATION

1760Gilsinn Lane, Fenton, MO 63026

PARTNUMBER

DESCRIPTIONOF CHANGE

REV

PARTNUMBER

SHEET

1 OF 1

12345678

Fig. 1

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

± .02

± .01

° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

125678

oPeRAtIon

Reclining the Handle

• Press the handle release pedal located on the back

of the vacuum with your foot to recline the handle

(Fig. 1).

On/Off Switch

• The power switch located on the vacuum handle, is a

three-way switch (Fig. 2). The middle position is the

“Off” setting, the rear position is the “On” setting and

the forward position is for “Maximum Power” (Fig. 3).

• Use the “Maximum Power” setting for carpet cleaning.

Use the “On” setting for cleaning bare floors and throw

rugs. Always turn the vacuum cleaner to the “Off”

setting before unplugging it from the electrical outlet.

Edge Cleaning

The edge cleaning feature provides improved cleaning

near walls and stationary furniture. For maximum edge

cleaning, place the left side of the nozzle, from the user’s

perspective, against the wall or stationary furniture.

Automatic Carpet Height Adjustment

Your vacuum is designed with an automatic self-

adjusting nozzle. No manual adjustments are required.

The height of the nozzle automatically adjusts to the

flooring surface. This self-adjusting feature allows the

nozzle to float evenly over all flooring surfaces.

Bare Floor Cleaning

Your vacuum is equipped with a squeegee on the bottom

of the vacuum to improve its effectiveness in cleaning

bare floors (Fig. 4). When cleaning tile, hardwood, vinyl,

etc., use the “On” setting for best results.

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESSOTHERWISE SPECIFIED

DESCRIPTION

DRAWINGSIZE:D

PARTNUMBER

SHEET 1 OF 1

X.X ± .02 IN RADII X.X ± .02

X.XX ± .01IN X,XX ± .01

X.XXX ± .005IN MACHINESURFACE

X.XXXX ± .0005 IN BREAK SHARP CORNERS TO .010 MAX

± 0 ° 30" COMMON TOBE CONCETRIC TO .002

TACONYCORPORATION CLAIMS PROPRIETARY

RIGHTSIN THE MATERIAL DISCLOSED HERE IN.

THISDRAWING IS ISSUED FOR ENGINEERING

INFORMATIONONLY. ITMAY NOT BE REPRO-

DUCED,NOR MAY THE INFORMATION HERE IN

BEUSED FOR MANUFACTURING PURPOSES

WITHOUTWRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

PARTNUMBER

DESCRIPTIONOF CHANGE

REV

PARTNUMBER

SHEET

1 OF 1

12345678

BYECNNODATEREV

5.000SCALE

Fig. 2

Fig. 1

Fig. 3

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

X.X ± .02 IN RADII X.X ± .02

X.XX ± .01 IN X,XX ± .01

X.XXX ± .005 IN MACHINE SURFACE

X.XXXX ± .0005 IN BREAK SHARP CORNERS TO .010 MAX

± 0 ° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

PART NUMBER

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

12345678

BYECN NODATEREV

5.000SCALE

OFF

MAX

POWER

Fig. 4

This vacuum is intended for household use only.

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

± .02

± .01

° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

12345678

Fig. 2

Power Cord Care

• If the cord or plug has any apparent damage,

refrain from using the vacuum. Please visit an

Authorized Simplicity Retailer for a new cord

or plug.

• When the vacuum is in use, hold the cord to

keep from running over it.

• Avoid obstructions and do not pull the cord

around sharp edges or corners.

• Always keep the cord away from heated

surfaces and never close doors on it as this

may cause damage to the wiring.

• To unplug, always grasp the plug, not the cord.

Vacuuming Under Furniture

Your vacuum will lay flat on the floor for effective

cleaning under beds and tables.

• Press the handle release pedal once for normal

vacuum cleaning (Fig. 1).

• Continue to lower the handle to enable the

vacuum to lay flat on the floor (Fig. 2).

MAIntenAnCe AnD CARe

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

± .02

± .01

° 30" COMMON TOBE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

1 OF 1

12345678

Fig. 1

Replacing the Vacuum Bag

NOTE: Unplug the vacuum cleaner

from the electrical outlet before

changing the bag.

• Unzip the bag compartment.

• Remove the used vacuum bag by

pulling the green bag collar tab away

from the vacuum (Fig. 1). Slide the

used bag out of the bag holder which

automatically seals the bag opening

(Fig. 2). Discard the used bag.

• To install a new bag, slide the bottom

of the green bag collar into the bag

holder until it “snaps” into place

(Fig. 3).

• Push the top of the bag collar

upward until the collar “snaps” into

place on the vacuum (Fig. 4).

• Tuck the bag corners into the bag

compartment then zip the bag

compartment closed.

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

.02 IN RADII X.X ± .02

.01 IN X,XX ± .01

.005 IN MACHINE SURFACE

.0005 IN BREAK SHARP CORNERS TO .010 MAX

0 ° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

678

Fig. 1

Fig. 2

MAIntenAnCe AnD CARe

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

.02 IN RADII X.X ± .02

.01 IN X,XX ± .01

.005 IN MACHINE SURFACE

.0005 IN BREAK SHARP CORNERS TO .010 MAX

0 ° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

678

Fig. 3

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

.02 IN RADII X.X ± .02

.01 IN X,XX ± .01

.005 IN MACHINE SURFACE

.0005 IN BREAK SHARP CORNERS TO .010 MAX

0 ° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

678

Fig. 4

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DESCRIPTION

DRAWING SIZE:D

PART NUMBER

SHEET 1 OF 1

.02 IN RADII X.X ± .02

.01 IN X,XX ± .01

.005 IN MACHINE SURFACE

.0005 IN BREAK SHARP CORNERS TO .010 MAX

0 ° 30" COMMON TO BE CONCETRIC TO .002

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

1.000

678

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Simplicity Staubsauger Handbücher

Simplicity

Simplicity S65S Bedienungsanleitung

Simplicity

Simplicity Pixie Bedienungsanleitung

Simplicity

Simplicity SV1 Bedienungsanleitung

Simplicity

Simplicity S20PET Bedienungsanleitung

Simplicity

Simplicity S18 Bedienungsanleitung

Simplicity

Simplicity 7 Series Bedienungsanleitung

Simplicity

Simplicity S24 Bedienungsanleitung

Simplicity

Simplicity S20EZM Bedienungsanleitung

Simplicity

Simplicity S40 Bedienungsanleitung

Simplicity

Simplicity Scout Plus Bedienungsanleitung

Simplicity

Simplicity Synergy X9 Bedienungsanleitung

Simplicity

Simplicity S20E Bedienungsanleitung

Simplicity

Simplicity FLASH Bedienungsanleitung

Simplicity

Simplicity S20 Bedienungsanleitung

Simplicity

Simplicity Freedom S10CV Bedienungsanleitung

Simplicity

Simplicity Synchrony S30P Bedienungsanleitung

Simplicity

Simplicity Symmetry Bedienungsanleitung

Simplicity

Simplicity SPORT Bedienungsanleitung

Simplicity

Simplicity S38 Bedienungsanleitung

Simplicity

Simplicity Moxie Bedienungsanleitung

Simplicity

Simplicity Freedom F3300 Bedienungsanleitung

Simplicity

Simplicity Freedom F3300 Bedienungsanleitung

Simplicity

Simplicity S24 Bedienungsanleitung

Simplicity

Simplicity Central Vacuum Power Units Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung