Simplicity S38 Bedienungsanleitung

When using an electrical appliance, basic precautions should always be followed, including the

following :

WARNING -

To reduce the risk of fire, electric shock, or injury :

11. Do not leave appliance when plugged in. Unplug from outlet when not in use and before

servicing.

12. Do not use outdoors or on wet surfaces.

13. Do not allow to be used as a toy. Close attention is necessary when used near children.

14. Use only as described in this manual.

Use only manufacturer's recommended attachments.

15. Do not use with damaged cord or plug. If appliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped into water, return it to a service center.

16. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around

sharp edges or corners. Do not run appliance over cord.

Keep cord away from heated surfaces.

17. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

18. Do not handle plug or appliance with wet hands.

19. Do not put any object into openings. Do not use with any opening blocked:

keep free of dust, lint, hair, and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

11. Turn off all controls before unplugging.

12. Use extra care when cleaning on stairs.

13. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where

they may be present.

14. This appliance is intended for household use only and not for commercial or industrial use.

15. Do not operate the cleaner if :

- the power cord is damaged.

- the hose shows visible signs of damage.

16. Do not use without dust bag and/or filters in place.

17. Hold plug when rewinding into cord reel. Do not allow plug to whip when rewinding.

18. The hose contains electrical wires. Do not use if damaged, cut or punctured.

Avoid picking up sharp objects.

19. To reduce the risk of electric shock, this appliance has a polarized plug.

20. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

21. Always turn off this appliance before connecting or disconnecting motorized nozzle.

22. Use only with motorized nozzle model SPB-250.

SAVE THESE INSTRUCTIONS

Read All Instructions Carefully Before Using This Appliance

IMPORTANT SAFETY INSTRUCTIONS

CONTENTS

CANISTER FEATURES .................................................. 4 ~ 5

HOW TO USE POWER NOZZLE ................................... 6 ~ 9

HOW TO USE CLEANING TOOLS .................................... 10

HOW TO REPLACE VACUUM BAG .................................. 10

HOW TO REPLACE FILTERS ............................................ 11

SAFETY PRECAUTIONS ................................................... 12

TROUBLESHOOTING GUIDE ........................................... 13

CANISTER FEATURES

FLOOR BRUSH STORAGE

POWER CONTROL HANDLE

DIRT SENSOR

Power Levels:

MAX 100%

HIGH 75%

MED 50%

LOW 25%

OFF 0%

CHECK

BAG

SERVICE

FILTER

POWER

BRUSH

MAX

HIGH

MED

LOW

OFF

POWER

BRUSH

OFF

Power nozzle

➪Please, refer to page 6~9.

Floor brush

One touch

integrated wand

On / Off Button

When lit, change

vacuum bag or

check for clog in

hose

When lit, change

HEPA filter

(page 11)

Light indicates

when power

nozzle is in use.

Power nozzle

On / Off

• Insert the wand holder into the parking slot on bottom or backside of u

Increase power

Decrease power

When light is

green your carpet

is clean.

When light is

orange keep

vacuuming-dirt is

found.

When light is red,

reset the circuit

breaker

switch(page 7).

LOOR BRUSH STORAGE

HOSE ADAPTER

MAIN ON / OFF BUTTON

CORD REWIND

Floor brush

On-board

cleaning tools

Flexible hose

Canister body

Adapter

button

er into the parking slot on bottom or backside of unit.

• When separating the hose from the body, press

the adapter buttons to release the hose.

• ON - Canister power is on and Power nozzle is off.

• OFF - All power is off.

Parking slot

HOW TO USE POWER NOZZLE

OPERATION

1. Turning on the Power Nozzle

The power nozzle can only be turned on if the

canister is also turned on (canister on / off

switch is located on the main body). The

power nozzle on / off switch is located on the

handle. Simply press the power nozzle button

to engage the power nozzle.

To achieve best cleaning results, slowly pass

the power nozzle back and forth over the

carpet or floor.

2. Using the Power Nozzle

After turning on the canister and power nozzle,

release the wand by pressing the left pedal on the

back side of the power nozzle (see diagram 3)

3. Remove / Insert the Wand From The Power

Nozzle

Removing the wand from the power nozzle

allows you, for example, to use cleaning tools

for baseboard or ceiling cleaning. To do this,

first turn the power nozzle and canister off.

Then, press the wand release collar (see

diagram 5) and pull the wand out. To reinsert

the wand into the power nozzle, simply press

the wand back into the neck of the power

nozzle. The wand will then "click" back into

place.

4. Carpet Height Adjustment

Your power nozzle has six different settings to

clean a variety of carpet types and floor

surfaces. To adjust the carpet height setting of

the power nozzle, press the right pedal located

on the back of the power nozzle (see diagram

6). Each press of this pedal will adjust the

height to the next carpet height position.

To determine which setting you are currently

on, locate and look through the height indicator

window on the top of the unit (see diagram 7).

You will see one of the six settings as

mentioned earlier and detailed below:

Setting: Intended Use:

1. XHI Very thick or plush carpet

2. HI Thick or plush carpet

3. Auto General carpet thickness and bare

floors

4. MED Average plush carpet

5. LO Thin plush carpet

6. XLO Low pile carpet (indoor/outdoor type

carpet)

Carpet Height Notes: When using the power

nozzle, start on the "auto" setting. If pushing the

power nozzle forward feels sluggish or hard to

push, then adjust to a higher setting (i.e. HI or

XHI). If the power nozzle feels very easy to push,

you may want to lower the power nozzle for more

effective cleaning. The "Auto" setting is the

recommended setting for hard floor surfaces (i.e.

tile, vinyl, wood).

Diagram 3

Diagram 6 Diagram 7

Diagram 5

Diagram 4

OPERATION

5. Warning Light / Dirt Sensor

Your power nozzle comes equipped with a

circuit breaker safety system that protects it

due to a jammed power nozzle situation.

Common items that cause jammed brushrolls

include socks, excessive threads, corners of

area rugs, etc. The warning indicator light on

top of the unit (see diagram 8) will change from

green to red should this condition occur.

If the circuit breaker trips:

a. Turn off the vacuum cleaner and power nozzle

then unplug the power cord.

b. Remove the object preventing the brushroll

from turning.

Locate the circuit breaker switch on the back of

the power nozzle and press it to reset the breaker

(see diagram 9).

When the unit is turned back on, the warning light

should be green and ready to go. If the circuit trips

again, repeat steps 1-3 again to correct the problem.

If this does not correct the problem, contact

your authorized vacuum cleaner retailer for

further assistance.

6. Dirt Sensor

The warning indicator light will turn orange if

the dirt sensor detects dirt in the carpet and

will change to green when the carpet is clean.

MAINTENANCE AND CARE

1. Removing the Brushroll

IMPORTANT: Before performing any

maintenance work on the power nozzle,

always unplug the vacuum cleaner and

disconnect the wand.

Your brushroll may need to be removed at

times, for example, to cut threads that have

become tangled around the brushroil or to

replace the belt (see "Replacing the Belt").

To remove the brushroll, turn the unit over and

lift off the metal bottom plate by first

unscrewing the two bottom plate screws

located by the rear wheels (see diagram 10).

Pull out the belt cover guard (see diagram 11)

and pull the brushroll out.

To reinstall the brushroll, reinsert the brushroll

back into the unit (make sure the belt is

attached properly). Next, insert the belt cover

guard. Then, place the metal bottom plate

back onto the unit (insert the front end of the

bottom plate first). Re-insert the two bottom

plate screws and secure.

Diagram 8

Warning Light / Dirt Sensor Circuit Breaker Switch

Diagram 9

Bottom

Plate Screws

Diagram 10 Diagram 11

MAINTENANCE AND CARE

2. Replacing the Power Nozzle Belt

IMPORTANT: Before performing any

maintena-nce work on the power nozzle,

always unplug the vacuum cleaner and

disconnect the wand.

To replace the power nozzle belt, you must

first remove the brushroll (see "Removing the

Brushroll"). Locate and discard broken belt.

To install new belt, locate the power nozzle

motor pulley and loop the belt around it (see

diagram 12). Place the other end of the belt

around the brushroll making sure the belt is

seated in the "belt groove" of the brushroll (see

diagram 13). Insert the brushroll back into the

brushroll tray and place the belt guard back

into position (see diagram 11). Place the

metal bottom plate back onto the unit (insert

the front end of the bottom plate first). Re-

insert the two bottom plate screws and secure.

3. Replacing the Bulb

IMPORTANT: Before performing any

maintenance work on the power nozzle,

always unplug the vacuum cleaner and

disconnect the wand.

Turn the power nozzle over and remove the

bottom plate by first unscrewing the two

bottom plate screws located by the rear

wheels (see diagram 10). Locate and remove

the two top cover screws (see diagram 14).

Turn the power nozzle back over, push the

power nozzle neck flat, and remove the top

cover (see diagram 15). Simply pull the bulb

out (no twisting) and reinsert a factory-

authorized bulb. Place the top cover back on

the unit, turn the machine over and re-insert

the two top cover screws. Reinstall the bottom

plate.

Diagram 12 Diagram 13 Diagram 14 Diagram 15

Belt Top Cover

Screw

DIAGRAM 1 REAR VIEW OF POWER WAND AND NOZZLE ASSEMBLY

DIAGRAM 2 FRONT VIEW OF POWER WAND AND NOZZLE ASSEMBLY

HOW TO USE CLEANING TOOLS

•On-board tools can be attached either to the power handle or to the end of the wand.

Floor brush: effective for hard surface cleaning (wood, tile, etc)

Upholstery tool: ideal for cleaning furniture

Dusting brush: (slides off the end of the upholstery tool) for shelves, tables, etc

Crevice: designed to clean in tight spaces (i.e. between sofa cushions)

Tool cover lid

button

Floor brush

Upholstery tool

Dusting brush

• Open the tool cover lid to access tools.

Crevice tool

REPLACING VACUUM BAG

•Turn canister off, remove

hose, and open the dust

cover.

•Grab the bag collar and pull

the vacuum bag out of the dust

bag holder. Insert new bag.

•Do not re-use vacuum bag.

•Dust cover will not close

without a bag in the unit or if

the bag is not fully inserted.

NOTE: The "change bag" light is located on the power handle and will light up when either the bag

is full or when a clog is detected in the machine. If upon inspection the bag is not full,

please inspect the hose or wand for a clog and remove.

Dust cover

latch. Dust bag

holder

Bag collar

Inhaltsverzeichnis

Andere Simplicity Staubsauger Handbücher

Simplicity

Simplicity S18 Bedienungsanleitung

Simplicity

Simplicity Whoosh Bedienungsanleitung

Simplicity

Simplicity SCRS SCRD SCRP Bedienungsanleitung

Simplicity

Simplicity S20E Bedienungsanleitung

Simplicity

Simplicity S65D Bedienungsanleitung

Simplicity

Simplicity a-go-go Bedienungsanleitung

Simplicity

Simplicity BRIO CANISTER Bedienungsanleitung

Simplicity

Simplicity Freedom S10E Bedienungsanleitung

Simplicity

Simplicity Symmetry Bedienungsanleitung

Simplicity

Simplicity Freedom F3300 Bedienungsanleitung

Simplicity

Simplicity Jill Bedienungsanleitung

Simplicity

Simplicity 7000 Series Bedienungsanleitung

Simplicity

Simplicity FLASH Bedienungsanleitung

Simplicity

Simplicity HEAVY DUTY SHD-1T Bedienungsanleitung

Simplicity

Simplicity S20 Bedienungsanleitung

Simplicity

Simplicity Jack Bedienungsanleitung

Simplicity

Simplicity SPORT Bedienungsanleitung

Simplicity

Simplicity Jill Bedienungsanleitung

Simplicity

Simplicity Moxie Bedienungsanleitung

Simplicity

Simplicity Central Vacuum Power Units Bedienungsanleitung

Simplicity

Simplicity S24 Bedienungsanleitung

Simplicity

Simplicity S36 Bedienungsanleitung

Simplicity

Simplicity SYMMETRY S20SC Bedienungsanleitung

Simplicity

Simplicity Symmetry Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch