SMART Board 600i3 Bedienungsanleitung

SMART Board™ 600i3

Interactive Whiteboard

System

Configuration and User’s

Guide

Product Registration

If you register your SMART product, we’ll notify you of new features and software

upgrades.

Keep the following information available in case you need to contact SMART

Technical Support.

Serial Number: ___________________________________________________

Date of Purchase: ___________________________________________________

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Trademark Notice

SMART Board, GoWire, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies

ULC in the U.S. and/or other countries. Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by SMART

Technologies ULC under license. Sanford. EXPO and EXPO2 are registered trademarks of Newell Rubbermaid. All other

third-party product and company names may be trademarks of their respective owners.

transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written

consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not

represent a commitment on the part of SMART.

Patent No. US6320597; US6326954; US6540366; US6741267; US7151533; US7184030; US7289113; and CA2058219.

Other patents pending.

07/2009

Introduction

Important Information

Read This Section First

NOTE

If you own a SMART product other than a SMART Board™ 600i3 interactive

whiteboard system, refer to the installation guide that came with your product for

relevant warnings and maintenance instructions.

In this document, “SMART Board 600i3 interactive whiteboard system” refers to the

SMART Board 600 series interactive whiteboard and its UF55/UF55w projector,

accessories and optional equipment. Before you install and use the SMART Board

600i3 interactive whiteboard system, read and understand the safety warnings and

precautions in this user’s guide, the projector user’s guide and the warnings

document. These safety warnings and precautions describe the safe and correct

operation of the interactive whiteboard system and its accessories, helping you

prevent injuries and equipment damage. You must always ensure that the interactive

whiteboard system is being used correctly.

The UF55/UF55w projector included with your system is designed to work only with

certain SMART Board interactive whiteboard models. Contact your authorized

SMART reseller for more information.

Safety Warnings, Cautions and Important Information

WARNINGS – GENERAL

• Do not climb (or allow children to climb) on any

part of your wall-mounted SMART Board

interactive whiteboard system.

• Climbing on the interactive whiteboard or

projector arm could result in personal injury or

product damage. Do not climb on, hang from or

suspend objects from the UF55/UF55w

projector’s arm.

ii | INTRODUCTION – IMPORTANT INFORMATION

• To reduce the risk of fire or electric shock, do not expose any component of

your SMART Board interactive whiteboard system to rain or moisture.

• Failure to follow the installation instructions shipped with your SMART product

could result in personal injury and damage to the product.

• Make sure that an electrical socket is near to your SMART product and

remains easily accessible during use.

• Two people are required to mount the projector boom and the interactive

whiteboard on a wall because they might be too heavy for one person to

maneuver onto their wall-mounting brackets.

• When mounting the projector boom on a framed wall, you must attach both

the mounting bracket and safety tether to a stud to safely support the

projector’s weight. If you use only drywall anchors, the drywall can fail,

resulting in product damage and possible personal injury.

• If you remove the bolt supporting the limit strap, the projector’s arm will be

free to swing. Make sure that the bolt is tightened, and never remove it from

the unit without supporting the projector’s arm first.

• Ensure that any cables extending across the floor to your SMART product are

properly bundled and marked to prevent a trip hazard.

• Cleaning a boom-mounted projector may result in a fall or injury.

WARNINGS – PROJECTOR

• Do not stare (or allow children to stare) directly into the beam of light created

by the projector. Instruct children not to look in the direction of, or stare at, this

beam of light. Encourage users to keep their back to the projector when

working at the interactive whiteboard. Before they turn to face the audience,

users should step sideways, out of the projector’s beam.

• Do not attempt to service the projector other than performing routine lamp

replacement. Other than the lamp module, there are no user-serviceable

parts inside the unit.

• Refer to the safety warnings and precautions published in the UF55/UF55w

projector manual.

• This projector detects its own remaining lamp life. Replace the lamp when

lamp life warning messages appear. If you continue to use the projector after

the replacement message appears, the lamp might shatter or burst, scattering

glass throughout the projector head.

• If the lamp has shattered or burst:

– Call an authorized SMART reseller for instructions. Do not attempt to

replace the lamp.

iii | INTRODUCTION – IMPORTANT INFORMATION

– Do not touch the glass fragments because they might cause injury.

– Leave and then ventilate the area where the lamp shattered or burst.

– Wash your hands thoroughly if you have come into contact with

lamp debris.

– Thoroughly clean the area around the projector, and discard any edible

items placed in that area because they might be contaminated.

• You must remove the projector from the projector’s arm before servicing

the lamp.

– Replacing the lamp in a boom-mounted projector might result in a fall

or injury.

– Uncovering the lamp while the projector is mounted on a projector’s arm

might lead to product damage or personal injury from falling pieces of

glass if the lamp is broken.

• When replacing the projector lamp:

– Turn the projector off and wait 30 minutes for the lamp to cool completely

before removing the projector from the boom.

– Do not remove any screws other than those specified in the lamp

replacement instructions.

– Wear protective eyewear while changing the lamp. Failure to do so can

cause injury or loss of eyesight if the lamp shatters or bursts.

– Use only replacement lamps approved by SMART Technologies. Contact

your authorized SMART reseller for replacement parts.

– Never replace the lamp assembly with a previously-used lamp assembly.

– To prevent premature lamp failure or exposure to mercury, always handle

the fragile lamp assembly with care. Use gloves when touching the lamp.

Do not touch the lamp with your fingers.

– Recycle or dispose of the lamp as hazardous waste, in accordance with

local regulations.

• When returning the projector to the boom, replace all of the screws you

removed when you removed the projector. Failure to do so can result in the

projector falling from the boom resulting in injury or equipment damage.

• To reduce the risk associated with a leaking battery in your projector’s remote

control:

– use only the specified coin-cell type battery

– orient the battery’s plus (+) and minus (-) terminal according to the

markings on the remote control

iv | INTRODUCTION – IMPORTANT INFORMATION

– remove the battery when the remote control is unused for an extended

period

– do not heat, disassemble, short or recharge the battery, or expose it to fire

or high temperatures

– avoid eye and skin contact if the battery has a leak

– dispose of the exhausted battery and product components in accordance

with applicable regulations

CAUTIONS

• Avoid turning off the projector during the lamp ignition phase as this may lead

to premature lamp failure. Before turning the projector off, keep the lamp on

for a minimum of 15 minutes after turning it on to preserve the lamp life.

• Never operate this unit immediately after moving it from a cold location to a

warm location. When the unit is exposed to such a change in temperature,

moisture may condense on the lens and crucial internal parts. Allow the

system to reach room temperature before operation to prevent possible

damage to the unit.

• In a high altitude location where the altitude is over 6000' (1828.8 m), where

the air is thin, cooling efficiency is reduced, so use the projector with the fan

mode set to High.

• Do not block the projector’s ventilation slots and openings.

• Do not place in hot locations, such as near heating equipment. Doing so could

cause a malfunction and shorten the life of the projector.

• Do not set up or use the interactive whiteboard system in an area with

excessive levels of dust, dirt, humidity or smoke.

• Before you clean the UF55/UF55w projector, put the system into Idle mode by

pressing the power button twice on the ECP or remote, and allow the bulb to

cool for 30 minutes.

• Do not allow liquids or commercial solvents of any kind to flow into the

projector base or head. Do not use spray cleaners or solvents near any part of

the projector, as it may damage or stain the unit.

• Cycling power to the projector repeatedly can lock or damage the interactive

whiteboard system. After you turn off the system, wait at least 15 minutes for

cooling before starting the system.

• Do not connect your serial cable directly to the projector’s RS-232 serial

interface. Use the extended control panel’s (ECP’s) RS-232 serial

interface only.

v | INTRODUCTION – IMPORTANT INFORMATION

• You must connect the USB cable that came with your SMART Board

interactive whiteboard to a computer that has a USB compliant interface and

that bears the USB logo. In addition, the USB source computer must be

compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL

Mark(s) for CAS/UL 60950. This is for operating safety and to prevent

damage to the SMART Board interactive whiteboard.

• Do not add extra weight or apply pressure to the UF55/UF55w projector

boom, the wall-mounted interactive whiteboard or its pen tray. SMART

Technologies designed the brackets to support only the weight of the

components during normal use.

• If the interactive whiteboard system requires replacement parts, make sure

that the service technician uses replacement parts specified by SMART

Technologies, or parts with the same characteristics as the original.

IMPORTANT

• Using the UF55/UF55w projector system near a TV or radio may cause

interference to the images or sound. If this happens, move the TV or radio

away from the projector.

• Do not place the interactive whiteboard system near any appliance that

generates a strong magnetic field.

• Do not place the interactive whiteboard system in direct sunlight.

• The screws that secure the interactive whiteboard to the wall are located

directly behind the pen tray. The pen tray must be removed before you can

remove the interactive whiteboard. When you secure the pen tray, you also

secure the interactive whiteboard.

• The SMART Board 600i3 interactive whiteboard system does not include

speakers. Consult your authorized SMART reseller to determine your audio

output options.

• If you have peripheral devices that do not use a 4-pin mini-DIN connector or

an RCA composite video jack, or if your device has an audio connection that

does not use RCA jacks, you may need to purchase third-party adapters.

• Disconnect the product from its power source when it’s not used for a

long period.

• When cleaning the interactive whiteboard system:

– Wipe the exterior of the projector using a lint-free cloth

– If necessary, use a soft cloth moistened with a mild detergent to clean the

projector housing

– Do not use abrasive cleaners, waxes or solvents

vi | INTRODUCTION – IMPORTANT INFORMATION

Transporting the SMART Board 600i3 Interactive Whiteboard

System

If you need to ship any part of your SMART Board 600i3 interactive whiteboard

system, repack it with the original packaging. If the original packaging is no longer

available, you may purchase replacement packaging from your authorized SMART

reseller.

If you prefer to use your own packaging materials, make sure that you adequately

protect the unit. Ship the interactive whiteboard in an upright position to deter shippers

from placing heavy objects on it.

Contents

Important Information ..............................................................................................i

Read This Section First .............................................................................i

Safety Warnings, Cautions and Important Information...............................i

Transporting the SMART Board 600i3 Interactive Whiteboard System ...vi

1About Your SMART Board 600i3 Interactive Whiteboard System ........................ 1

SMART Board 600i3 Interactive Whiteboard System Features...................... 2

Interactive Whiteboard Features .............................................................. 3

UF55/UF55w Projector System Features................................................. 3

ECP and Cable ........................................................................................ 4

Standard Accessories..................................................................................... 5

Remote Control ........................................................................................ 5

Pen Tray Tools......................................................................................... 5

Eraser....................................................................................................... 5

Optional Accessories ...................................................................................... 6

SMART Board Audio (SBA) USB Speakers............................................. 6

GoWire SMART Notebook Software

Auto-launch Cable (USB-GW).................................................................. 6

Active USB Extension Cables (USB-XT).................................................. 6

Wireless Bluetooth Connection (WC6)..................................................... 6

Cat 5 to USB Cable Extender (CAT5-XT) ................................................ 6

Serial Conversion Module (RS-232)......................................................... 6

2Installing Your SMART Board 600i3 Interactive Whiteboard System ................... 7

Environmental Requirements ......................................................................... 8

Temperature Range ................................................................................. 8

Humidity ................................................................................................... 8

viii | CONTENTS

Water and Fluid Resistance ..................................................................... 9

Dust and Scratching................................................................................. 9

Electrostatic Discharge (ESD).................................................................. 9

Cables ...................................................................................................... 9

Conducted and Radiated Emissions ........................................................ 9

Before Installing Your SMART Board 600i3 Interactive

Whiteboard System ...................................................................................... 10

Recommended Mounting Heights .......................................................... 10

After Installing Your SMART Board 600i3 Interactive

Whiteboard System ...................................................................................... 11

Adjusting Keystone Alignment ............................................................... 11

Focusing the Image................................................................................ 12

Performing an Image Alignment............................................................. 13

Securing the Pen Tray and the Interactive Whiteboard.......................... 17

3Connecting Your SMART Board 600i3 Interactive Whiteboard System ............. 19

Installing SMART Notebook Software .......................................................... 20

Connecting the Cables to the UF55/UF55w Projector.................................. 21

Routing the Cables................................................................................. 21

Connecting Your Guest Computer to the ECP’s Inputs ......................... 25

Connecting Peripheral Visual or Audio-Visual Devices ................................ 26

4Using Your SMART Board 600i3 Interactive Whiteboard System ...................... 27

Turning the System On and Off and Selecting an Input ............................... 28

Using Your Interactive Whiteboard ............................................................... 28

Using Your UF55/UF55w Projector .............................................................. 29

Using Your Remote Control ................................................................... 29

Menu Options......................................................................................... 29

5Troubleshooting Your SMART Board 600i3 Interactive Whiteboard System...... 33

System Warning Lights................................................................................. 34

ECP Ready Light and System Status..................................................... 34

Projector Ready Lights and Projector Status ......................................... 34

Andere Handbücher für Board 600i3

Inhaltsverzeichnis

Andere SMART Interaktives Whiteboard Handbücher

SMART

SMART SMART Board V280 Bedienungsanleitung

SMART

SMART Table 230i Bedienungsanleitung

SMART

SMART SBID8055i-G5-SMP Service-Handbuch

SMART

SMART KAPP iQ PRO 55 Service-Handbuch

SMART

SMART 2000i-DVS Bedienungsanleitung

SMART

SMART 8070i-G4-SMP Betriebsanleitung

SMART

SMART FS640 Bedienungsanleitung

SMART

SMART Board 600i4 Bedienungsanleitung

SMART

SMART Board 6065 Betriebsanleitung

SMART

SMART SBID-7286 Bedienungsanleitung

SMART

SMART kapp iQ 55 Service-Handbuch

SMART

SMART SC12A Benutzerhandbuch

SMART

SMART SPNL-6065 Bedienungsanleitung

SMART

SMART board 8000i-G4 series Betriebsanleitung

SMART

SMART 880i5-SMP Bedienungsanleitung

SMART

SMART Smart Board M600 series Bedienungsanleitung

SMART

SMART UF45-680 Bedienungsanleitung

SMART

SMART 8070i-SMP Bedienungsanleitung

SMART

SMART Inforce 67X1 Bedienungsanleitung

SMART

SMART SBID 8000 series Bedienungsanleitung

SMART

SMART KAPP42 Bedienungsanleitung

SMART

SMART KAPP42 Bedienungsanleitung

SMART

SMART SBX885 Bedienungsanleitung

SMART

SMART 8070i Bedienungsanleitung

Beliebte Interaktives Whiteboard Handbücher anderer Marken

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Bedienungsanleitung

Buhl

Buhl LyteBoard Bedienungsanleitung

SMART Board

SMART Board 680 Bedienungsanleitung

Legamaster

Legamaster e-SCREEN ETX Bedienungsanleitung

SMART Board

SMART Board SBM685ix2 Bedienungsanleitung

Seneca

Seneca eno Bedienungsanleitung

BenQ

BenQ RP840G Bedienungsanleitung

Olivetti

Olivetti OLIBOARD Bedienungsanleitung

Turning Technologies

Turning Technologies MOBIVIEW Bedienungsanleitung

Panasonic

Panasonic UB-5335 Bedienungsanleitung

Dukane

Dukane ITP84 Bedienungsanleitung

Bretford

Bretford EDUIMS Konfigurationshandbuch

Panasonic

Panasonic Panaboard UB-5315 Bedienungsanleitung

Plus

Plus M-11S Bedienungsanleitung

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Bedienungsanleitung

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Bedienungsanleitung

AVer

AVer CP series Bedienungsanleitung

Genee

Genee 56" Bedienungsanleitung