SMART SBID 8084i-G4 Bedienungsanleitung

Inhaltsverzeichnis

Andere SMART Interaktives Whiteboard Handbücher

SMART

SMART SBID 8070i-G4 Bedienungsanleitung

SMART

SMART Podium 500 Series Bedienungsanleitung

SMART

SMART KAPP42 Bedienungsanleitung

SMART

SMART 8070i-SMP Bedienungsanleitung

SMART

SMART Board 6065 Betriebsanleitung

SMART

SMART 8070i Bedienungsanleitung

SMART

SMART kapp iQ 55 Bedienungsanleitung

SMART

SMART Inforce 67X1 Bedienungsanleitung

SMART

SMART SBX885 Bedienungsanleitung

SMART

SMART Board 600i4 Bedienungsanleitung

SMART

SMART 880i5-SMP Bedienungsanleitung

SMART

SMART Board 885ix2-NCP Bedienungsanleitung

SMART

SMART Board 685ix Bedienungsanleitung

SMART

SMART Table 230i Bedienungsanleitung

SMART

SMART KAPP IQ Bedienungsanleitung

SMART

SMART M680 Bedienungsanleitung

SMART

SMART Board 800 Series Bedienungsanleitung

SMART

SMART Room System SRS-LYNC-XS Service-Handbuch

SMART

SMART Podium ID350 Bedienungsanleitung

SMART

SMART Table 230i Installationshandbuch

SMART

SMART KAPP iQ PRO 55 Service-Handbuch

SMART

SMART SMART Board Bedienungsanleitung

SMART

SMART Sympodium ID250 TM Bedienungsanleitung

SMART

SMART KAPP42 Bedienungsanleitung

Beliebte Interaktives Whiteboard Handbücher anderer Marken

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Bedienungsanleitung

Buhl

Buhl LyteBoard Bedienungsanleitung

SMART Board

SMART Board 680 Bedienungsanleitung

Legamaster

Legamaster e-SCREEN ETX Bedienungsanleitung

SMART Board

SMART Board SBM685ix2 Bedienungsanleitung

Seneca

Seneca eno Bedienungsanleitung

BenQ

BenQ RP840G Bedienungsanleitung

Olivetti

Olivetti OLIBOARD Bedienungsanleitung

Turning Technologies

Turning Technologies MOBIVIEW Bedienungsanleitung

Panasonic

Panasonic UB-5335 Bedienungsanleitung

Dukane

Dukane ITP84 Bedienungsanleitung

Bretford

Bretford EDUIMS Konfigurationshandbuch

Panasonic

Panasonic Panaboard UB-5315 Bedienungsanleitung

Plus

Plus M-11S Bedienungsanleitung

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Bedienungsanleitung

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Bedienungsanleitung

AVer

AVer CP series Bedienungsanleitung

Genee

Genee 56" Bedienungsanleitung

1 smarttech.com/kb/170597 1022737 Rev 01

Important

Before you configure your

SMARTBoard® 8084i-G4

interactive flat panel

You need to set the computer (or Microsoft®Lync® appliance) input’s operating mode to “PC” after

you turn on your SMARTBoard® 8084i-G4 interactive flat panel for the first time but before you

configure and use the interactive flat panel.

I M P O R T A N T

If you do not complete this procedure, the following could occur:

lThe interactive flat panel might not display the outer edges of the computer’s display.

lUsers might notice higher than normal video display latency.

To set the computer input’s operating mode to “PC”

1. Turn on the interactive flat panel.

2. If you’re installing the interactive flat panel as part of a SMARTRoomSystem™ for

MicrosoftLync, set the Lync Room Reset option as described in chapter 3 of the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

3. On the remote control, press INPUT (a), and then press the red button (b),

which is below the BACK button.

The Input Label menu appears.

I M P O R T A N T

Before you configure your SMARTBoard 8084i-G4 interactive flat panel

2 smarttech.com/kb/170597 1022737 Rev 01

4. Using the left and right arrow buttons on the remote control, select the input that the computer is

connected to, and then press OK.

N O T E

If you’re installing the interactive flat panel as part of a SMARTRoomSystem, select

HDMI3/PC.

5. Using the left, right, up and down arrow buttons on the remote control, select PC, and then

pressOK.

6. Press the down arrow on the remote control to select Close, and then press OK.

In the Input List menu, the computer input’s icon indicates that its operating mode is “PC.”

7. Calibrate and orient the interactive flat panel as documented in the SMARTBoard 8000i-G4

interactive flat panel setup and maintenance guide (smarttech.com/kb/170446) or the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

N O T E

In most situations, the only time you need to make this change is during the initial

configuration of the interactive flat panel. However, if you subsequently complete a

FactoryReset or LyncRoomReset, you need to complete this procedure afterward.

smarttech.com/support

smarttech.com/contactsupport

© 2013SMARTTechnologiesULC. All rights reserved. SMARTBoard, SMARTRoomSystem, smarttech, the SMART logo and all SMART taglines are trademarks or

registered trademarks of SMARTTechnologiesULC in the U.S. and/or other countries. Microsoft and Lync are either registered trademarks or trademarks of Microsoft

Corporation in the U.S. and/or other countries. All other third-party product and company names may be trademarks of their respective owners. Contents are subject to

change without notice. 10/2013.