SMC Networks 7901BRA2 - annexe 2 Bedienungsanleitung

TELNET Command Line Interface

Quick Reference Syntax 1.0.10

Command syntax Short Description

SYSTEM part level II

information <CR> Show system hardware information

op_mode <Router|Bridging|Host> Kernel operation mode

hostname [name] Config local hostname

domain_name [domain] Config local domain name

group_name <name> Config group name for NetBIOS resource share

time_zone <0~62> Time zone ID

use_time_server <Disable|Enable> [time] Using time server or base time

update_interval <1~72> Update interval (hours)

daylight_save <Disable|Enable> Automatic daylight saving

time_server <ip> [ip] [ip] Time servers

clone_mac <Default|PC's|mac> Clone WAN port MAC address

system

response_mode <Normal|Brief> Config response mode in CLI

INTERFACE part level II address <ip> <netmask> Interface IP address & netmask

link_type <Disable|Ethernet> Config interface link type

nat_type <Public|Private> NAT network type

bridge <Disable|Enable> Config interface bridging function state

access-list <0~4> <0~4> Binding interface access-list

device-filter <0~4> <0~4> Binding interface device-filter rules

access_ctrl <Disable|Enable> Enable or disable access control

inspect-rule <0~4> <0~4> Binding interface inspection rule

network_secure <Untrust|Trust> Config interface security type

lan <1~4>

vlan <0~4> Config VLAN profile index

address <ip> <netmask> Interface IP address & netmask

link_type <Disable|Ethernet> Config interface link type

nat_type <Public|Private> NAT network type

bridge <Disable|Enable> Config interface bridging function state

access-list <0~4> <0~4> Binding interface access-list

device-filter <0~4> <0~4> Binding interface device-filter rules

access_ctrl <Disable|Enable> Enable or disable access control

inspect-rule <0~4> <0~4> Binding interface inspection rule

network_secure <Untrust|Trust> Config interface security type

wireless <1~1>

vlan <0~4> Config VLAN profile index

interface

atm <1~8> address <ip> <netmask> Interface IP address & netmask

link_type <Disable|Ethernet|PPP|IPoA> Config interface link type

nat_type <Public|Private> NAT network type

bridge <Disable|Enable> Config interface bridging function state

dial <1~20> <0~32767> <-1~30> Config dial profile index and attributes

vc <1~8> Specify VC profile index

access-list <0~4> <0~4> Binding interface access-list

device-filter <0~4> <0~4> Binding interface device-filter rules

access_ctrl <Disable|Enable> Enable or disable access control

inspect-rule <0~4> <0~4> Binding interface inspection rule

network_secure <Untrust|Trust> Config interface security type

remote_route <ip> [Disable|Enable] Remote IP address and add route

dns <ip> [ip] ISP provides DNS IP addresses

ip_assign <Dynamic|Fixed> Dynamic get IP address or use fixed IP

vlan <0~4> Config VLAN profile index

dhcp_clt <Disable|Enable> Enable or disable DHCP client

address <ip> <netmask> Interface IP address & netmask

link_type <Disable|PPPoE> Config interface link type

ether_interface <interface> Config PPP over ehternet interface number

dial <1~20> <0~32767> <-1~30> Config dial profile index and attributes

access-list <0~4> <0~4> Binding interface access-list

device-filter <0~4> <0~4> Binding interface device-filter rules

access_ctrl <Disable|Enable> Enable or disable access control

inspect-rule <0~4> <0~4> Binding interface inspection rule

network_secure <Untrust|Trust> Config interface security type

ip_assign <Dynamic|Fixed> Dynamic get IP address or use fixed IP

pppoe <1~8>

vlan <0~4> Config VLAN profile index

lan_sec <1~1> address <ip> <netmask> Interface IP address & netmask

ps. The command `lan_sec` is for telefonica vendor.

VLAN part level II

name <string> VLAN profile description

ipnet <ip> <netmask> VLAN subnet value

igmp-snooping <Disable|Enable> Config IGMP-Snooping function

igmp-querier <Disable|Enable> Config IGMP-Querier function

vlan <1~4>

func <Disable|Enable> Enable or disable this VLAN port

WLAN part level II

wlan country <1~76> Country selection

SSID <string> SSID

hide_ssid <Disable|Enable> Hide SSID

channel <0~13> Current operating frequency channel

tx_rate <Auto|54|48|36|24|18|12|11|9|6|5.5|2|1> Transmission rate (Mbit)

mode <mixed|long_range|g_only|b_only> Wireless mode

stationName <string> Station name

rtsThreshold <0~3000> RTS threshold

fragThreshold <256^2346> Fragmentation threshold (even numbers only)

func <Disable|Enable> Enable MAC filter

access_rule <Deny|Allow> Access rule for registered MAC address

add <mac> Add MAC address

delete <1~32> Delete MAC address

mac_filter

modify <1~32> <mac> Modify MAC address

mode <Disable|Enable> [64|128] WEP mode

dyna_key_prov <Disable|Enable> Key provisioning, static or dynamic

defaultKeyId <1~4> WEP default key ID

defaultKeys64 <1~4> <hex> 64 bits WEP key table (Hex)

defaultKeys128 <1~4> <hex> 128 bits WEP key table (Hex)

key64ascii <1~4> <string> 64 bits WEP key table (ASCII)

key128ascii <1~4> <string> 128 bits WEP key table (ASCII)

passphrase64 <string> Passphrase for 64 bits WEP key

wep

passphrase128 <string> Passphrase for 128 bits WEP key

mode <Disable|Enable> [802.1X|PSK] WPA mode

psk_type <Passphrase|Hex> Pre-shared key type

psk_hex <hex> 256 bits PSK

psk_passphrase <string> Passphrase for PSK

obscure_psk <Disable|Enable> Obscure PSK

rekey_period <Disable|Seconds|Packets> Rekey period

rekey_second <number> Rekey second

wpa

rekey_packet <number> Rekey packet

func <Disable|Enable> Enable/Disable 802.1X

session_timeout <number> Session idle timeout (milli seconds)

re_auth_period <number> Re-authentication period (milli seconds)

quiet_period <number> Quiet period (milli seconds)

server_ip <ip> Server IP

server_port <1~65534> Server port

secret_key <string> Secret key

802.1x

radius

nas_id <string> NAS-ID

func <Disable|Enable> WDS functionality

func <1~4> <Disable|Enable> MAC of LAN mode to be use

wds connect mac <1~4> <mac> MAC of LAN mode

func <Disable|Enable> Wireless disable or enable

security_mode <disable|wep|wpa2_only|wpa_wpa2> Config wireless security mode

BRIDGE part level II

generic <Disable|Enable> <ip> <netmask> Config bridging function, IP and subnet mask

mac_address <mac> Config mac address

LAN1_port <Filter|Forward|Dynamic> Config LAN1 bridging type

WLAN1_port <Filter|Forward|Dynamic> Config WLAN1 bridging type

ATM1_port <Filter|Forward|Dynamic> Config ATM1 bridging type

ATM2_port <Filter|Forward|Dynamic> Config ATM2 bridging type

ATM3_port <Filter|Forward|Dynamic> Config ATM3 bridging type

ATM4_port <Filter|Forward|Dynamic> Config ATM4 bridging type

ATM5_port <Filter|Forward|Dynamic> Config ATM5 bridging type

ATM6_port <Filter|Forward|Dynamic> Config ATM6 bridging type

ATM7_port <Filter|Forward|Dynamic> Config ATM7 bridging type

ATM8_port <Filter|Forward|Dynamic> Config ATM8 bridging type

LAN2_port <Filter|Forward|Dynamic> Config LAN2 bridging type

LAN3_port <Filter|Forward|Dynamic> Config LAN3 bridging type

LAN4_port <Filter|Forward|Dynamic> Config LAN4 bridging type

WDS1_port <Filter|Forward|Dynamic> Config WDS1 bridging type

WDS2_port <Filter|Forward|Dynamic> Config WDS2 bridging type

WDS3_port <Filter|Forward|Dynamic> Config WDS3 bridging type

add

WDS4_port <Filter|Forward|Dynamic> Config WDS4 bridging type

delete <1~20> Delete static MAC entry