Socket CX2881-1476 Bedienungsanleitung
QUICK START GUIDE
CHS 8Ci
Bluetooth Cordless Scanner
This document pertains to the following model:
CHS 8Ci - Black SKU# CX2881-1476 (P/N 8550-00069)
CHS 8Ci - White SKU# CX2893-1497 (P/N 8550-00072)
PACKAGE CONTENTS
© 2013 Socket Mobile, Inc. All rights reserved. Socket and the Socket logo are registered
trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark and logo are
registered trademarks of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc.
is under license. All other trademarks and trade names contained herein may be those of
their respective owners.
CHS 8Ci Lanyard USB Charging Cable
PRODUCT INFORMATION
3
PRODUCT SPECIFICATIONS
Light Source 630nm +- 30nm visible red LED
Scan Rate 5 scans / sec
Sensor Linear CMOS sensor
Resolution 5mil / 0.127mm
Bluetooth Prole SPP, HID
Battery Life 8 hours (1 scan / 5 sec)
Charge Time 4 hours fully charged
Wireless Range 10M / 33ft line of sight
Operating Temp 0° to 50° C (32° to 122° F)
Symbologies All major 1D barcodes
4
CHARGE THE BATTERY
Charge the CHS
The CHS must be fully charge before rst use. Initial charging takes 4
hours with the USB charging cable connected to a USB charging port.
Insert the Micro USB side of the USB Charging Cable (included) into
the CHS port and the USB side of the Charging Cable into the USB con-
nector of an AC adapter (not included). The CHS will beep twice when
connected to a USB Charging Port.
Power On
Press and hold down the small power button until the CHS beeps (low-
high tone).
See below for instructions on pairing and connecting your scanner
with your Apple or Android devices.
5
4 Hours
GETTING STARTED
Successful Scanning
1. Hold the scanner 5-7 cm away
from the barcode.
2. Aim the scan beam straight
across the entire barcode.
3. Keep your hand steady!
6
BLUETOOTH MODE HID SPP iOS
The CHS 8Ci supports three modes of Bluetooth wireless
communication: HID, SPP, and iOS.
By default, the CHS 8Ci is set to HID Keyboard mode.
Operating System Apple Android Windows
HID ✓✓✓
SPP ✓ ✓
iOS ✓
HID (Human Interface Device): Default mode. No software installation
required.
SPP (Serial Port Prole): Recommended for Android, Windows
and other operating systems. Allows two-way communications.
SocketScan 10 software (available at socketmobile.com) or another
third party SDK application is required.
iOS: Recommended for Apple. Allows two-way communications.
Compatible application developed with SocketScan 10 SDK required.
Learn more about HID and SPP at http://www.socketmobile.com/
pdf/techbrief/socketscan-10-sdk_white-paper.pdf 7
BLUETOOTH BASICS
Pair and Connect
When Bluetooth is activated on your device and the CHS is in
discoverable mode, Bluetooth pairing will begin. When the two devices
recognize each other, they can pair.
Once the devices have paired, it is necessary to connect. (Follow the
instructions in the following pages to connect the CHS to your device.)
Once the devices have connected, they will automatically recognize
each other whenever they are within range, and it will not be
necessary to connect again.
If the CHS is connected to a device and gets disconnected, it will try to
reconnect. Make sure the computer or device is on and in range. If the
CHS cannot reconnect, it will beep long. Power o then on again to
reconnect.
To unpair from the last connected host, press and hold the trigger
button while turning o the scanner.
8
The CHS 8Ci keeps the pairing information of the last connected host.
Power o to disconnect the scanner, then power on to reconnect the
scanner.
To disconnect your CHS:
1. Power o - press and hold down the power button until the CHS
beeps (high-low tone).
2. Power on - press and hold down the power button until the CHS
beeps (low-high tone).
Your CHS is ready to reconnect.
BLUETOOTH BASICS
9
APPLE BLUETOOTH MODE HID (KEYBOARD EMULATION)
Connect your CHS with an Apple device using HID mode.
(HID is the default mode.)
1. Power on the CHS.
2. Scan this barcode to set the CHS to HID mode.
3. Enable Bluetooth on the Apple device. A Bluetooth device search
will begin.
4. Select Socket CHS in the list of found devices.
5. Tap Pair if prompted.
6. The CHS will beep once to conrm connection.
Now you are ready to scan barcodes in HID mode using your Apple
device!
10
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Socket Scanner Handbücher
Socket
Socket 7X Bedienungsanleitung
Socket
Socket CHS 7Xi Bedienungsanleitung
Socket
Socket Secure Digital Scan Card Series 3 Bedienungsanleitung
Socket
Socket CHS 7DiRx Bedienungsanleitung
Socket
Socket CHS Series 7 Bedienungsanleitung
Socket
Socket Bluetooth iPAQ Bedienungsanleitung
Socket
Socket CHS Series 7 Bedienungsanleitung
Socket
Socket CHS 7P Bedienungsanleitung
Socket
Socket 7X Bedienungsanleitung
Socket
Socket CHS 7DiRx Installationshandbuch
Socket
Socket Cordless Hand Scanner Bedienungsanleitung
Socket
Socket 7X Bedienungsanleitung
Socket
Socket CRS Series 9 Bedienungsanleitung
Socket
Socket Cordless Ring Scanner Series 9 Bedienungsanleitung
Socket
Socket CompactFlash Scan Card Series 5 Bedienungsanleitung
Socket
Socket CF RFID Reader-Scan Card Series 6 Bedienungsanleitung
Socket
Socket CHS 7XiRx Bedienungsanleitung
Socket
Socket CHS 7Ci Bedienungsanleitung
Socket
Socket 1D Bedienungsanleitung
Socket
Socket CHS Series 7 Bedienungsanleitung
