Soleus Air SG-WAC-05SM Bedienungsanleitung

5,000 BTU Window Air Conditioner

Operating Instructions

Model No. SG-WAC-05SM

Thank you for choosing a Soleus Air powered by Gree Air Conditioner. This owner’s manual will

provide you with valuable information necessary for the proper care and maintenance of your new

product. Please take a few moments to thoroughly read the instructions and familiarize yourself with

all the operational aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

Recommended Ground Method

For your personal safety, this air conditioner must be grounded. This air conditioner is equipped with a 3 prong power

supply cord with a grounded plug. To minimize the possibility of electrical shock, the cord must be plugged into a 3 prong

outlet and grounded in accordance with all local codes and ordinances. If a 3 prong outlet is not available, it is the cus-

tomer’s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrician.

LCDI Power Cord and Plug

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as

required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination

on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the nominal current

leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain de-

energized until the devise has been manually reset. This is intended to reduce the risk of a fire in the power cord or

combustible materials nearby. The cord shields are not grounded and they must be considered a shock hazards if

exposed. The cord shield must not be connected to ground or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if

the plug is functioning properly. To test the plug:

1. Plug power cord into a wall outlet

2. Press the TEST Button, the circuit should trip and cut all

power to the air conditioner

3. Press the RESET button for use

If a test is performed and the indicator light remains ON, the

current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer

Service for troubleshooting recommendations.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong.

Do not use an adapter

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock

The electrical ratings for your air conditioner are listed on the model and serial

number label located on the front left side of the unit (when facing the front).

Specific electrical requirements are listed in the chart below. Follow the

requirements below for the type of plug on the power supply cord.

Power Supply Cord

• 115 volt (103.5 min.—126.5

max)

• 0-12 amps

• 15-amp time-delay fuse or

circuit breaker

• Use on single outlet circuit only

Wiring Requirements

It is the customer’s responsibility:

• To contact a qualified electrician

• To assure that the electrical installation is adequate

and in conformance with the National Electrical Code,

ANSI/NFPA 70 - latest edition, and all local codes and

ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

PACKING LIST

• Window Air Conditioner

• Top Mounting Rail

• Top Mounting Rail Seal Strip

• 3/8” Screw for Top Mounting Rail (4)

• Accordion Panels (2)

• Window Locking Bracket

• Window Sash Seal

• 3/4” Screw for Window Locking Bracket and Accordion Panels (5)

• Foam Top Window Gasket

• Owner’s Manual

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT

TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN.

Model SG-WAC-05SM

Power Supply (Ph/V/Hz) 1/115/60Hz

Dehumidifying Capacity (Pints/Day) 38.4

Rated Cooling Capacity (BTU/h) 5,000

Rated Heating Capacity (BTU/h) /

Cooling Power Input (Watts) 515

Heating Power Input (Watts) /

Rated Current Cooling (Amperage) 4.9

Rated Current Heating (Amperage) /

EER/C.O.P 9.7 EER

Noise Level db (A) H/L 55/62

CFM 120

Design Pressure (PSIG) (H/L) /

Dimensions (W” x H” x D”) 16.125 x 13.25 x 12

Package Dimensions (W” x H” x D”) 17.875 x 14.375 x 15.25

Net/Gross Weight (Lbs) 40

Refrigerant Charge (Oz) 44

INSTALLATION & ASSEMBLY INSTRUCTIONS

Some assembly is required for your new air conditioner. Please read and follow these instructions carefully.

1. This air conditioner is designed to be installed in a

standard double-hung window with a window width

between 23” and 36” (584 mm - 914 mm).

2. The air conditioner can be installed without the

accordion panels to fit in a narrow window opening.

See the window dimensions.

3. The Lower Sash (the lower part of the window that

moves up and down) must allow for 14.5” of vertical

clearance when open. (See FIG. 1).

4. All supporting parts must be secured to firm wood,

masonry, or metal.

5. The electrical outlet must be within reach of the power

cord.

Top Rail Assembly

The top rail must be assembled prior to installing the air conditioner in the window

Tools Needed: Phillips Screw Driver

Attaching the Top Rail to the Air Conditioner

Top Rail Hardware QTY

3/8”

Screw

Top

Panel

1. Remove the air conditioner from the box

and place on a hard flat surface.

2. Remove top rail from the bottom of the

packaging material as shown in FIG. A

3. Align the hole in the top rail with those in

the top of the unit as shown in FIG. B

4. Secure the top rail to the unit with the 3/8"

Screws as shown in FIG. C

Top Rail

Box

FIG. A

FIG. C

FIG. B

NOTE: Save the product packaging and installation instruc-

tions for future reference. Store the air conditioner in the

product box when not in use for an extended period of time.

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

FIG. 1

NOTE: For safety reasons, all 4

screws must be used to attach

the top rail.

ASSEMBLY & INSTALLATION (CONT.)

Storm Window Requirements

A storm window frame will not allow the air conditioner to

tilt properly which in turn will keep it from draining properly.

To adjust for this, attach a board or piece of wood to the

sill. The board or wood piece should have a depth of at

least 1 1/2”. Make sure the board or piece of wood is ap-

proximately 1/2” higher than the storm window frame. This

will allow the air conditioner to tilt enough for proper drain-

age. (See FIG. 2).

Placing the Unit Inside a Window

1. Place the air conditioner on the sill with the bottom

mounting rail against its back edge. Center the air con-

ditioner and close the window securely behind the top

mounting rail. The air conditioner should be slightly

tilted to the outside area. Use a level; about a 1/3 bub-

ble will be the correct case slant to the outside. (See

FIG. 5 & FIG. 6)

2. Once the air conditioner is placed, extend both the left

and right accordion panels to the width of the window.

Accordion Panel Installation

Now that you have installed the top rail, you can now install

the accordion panels on each side.

1. Place the air conditioner on a hard flat surface.

2. Locate the accordion panels in the box.

3. Gently pull the free end of the accordion panel (See

FIG. 2). Do this for both panels.

4. Slide the free end of the accordion panel into the side

panel of the air conditioner (See FIG. 3). Do this for

each side.

5. Once the accordion panels are slid into place adjust

the top and bottom rails of the accordion panels into

the top and bottom rails of the air conditioner (See FIG.

4).

SASH

1 1/2” MIN

(38 mm)

STORM

WINDOW

FRAME

Board or wood

piece must be

approximately

1/2” higher

than the storm

window frame

for proper

drainage

FIG. 2

FIG. 3

FIG. 4

FIG. 2

FIG. 5

FIG. 6

FIG. 7

ASSEMBLY & INSTALLATION (CONT.)

3/4” Screws

Frame Lock

Sash Lock

MOUNTING HARDWARE

Qty

Tools Needed:

Phillips Screw Driver

Drill (if plot holes are needed)

Frame Lock, Sash Lock, and Foam Seal

Installation

1. Place the frame lock between the extended accordion

panels and the window sill as show in FIG. 8. Screw a

3/4” (19 mm) locking screw through the frame lock and

into the window sill (FIG. 9).

2. Drive 1/2” screws into the top of the accordion panel

frame and the top rail to securely attach the window air

conditioner to the lower sash. (See FIG. 11/12)

3. To secure the lower sash into place, use the sash lock

and a 3/4” screw as shown below (See FIG. 12)

4. For added insulation, cut the supplied insulation foam to

the width of the window. Insert the foam between the

window sashes to prevent air and objects from getting

into the room. (See FIG. 13)

Removing the Air Conditioner from the

Window

1. Turn the air conditioner off, and disconnect the power

cord.

2. Remove the sash seal from between windows, and

unscrew sash lock.

3. Remove the screws installed through the frame and

frame lock.

4. Close (slide) the side panels into frame.

5. Keeping a firm grip on air conditioner, raise the sash

and carefully “rock” air conditioner backward to drain

any condensate water in base of unit. Be careful not to

spill any remaining water while lifting unit from window.

6. Store parts WITH the air conditioner in the box

FIG. 13

USING YOUR AIR CONDITIONER

Manual Control Panel

Operating Your Air Conditioner

1. Power: Turn on the unit by rotating the

MODE dial to the desired setting.

2. Cooling Mode: For maximum cooling set the

MODE dial to “HIGH COOL”. In HIGH COOL

mode, the fan will automatically go to high.

This will help circulate the cool air throughout

the room. The fan will operate on low in “LOW

COOL” mode

3. Fan Mode: For fan only modes, choose

either HIGH FAN or LOW FAN. The air

conditioner will not cool the room when in fan

mode.

4. Thermostat: Turn the TEMP dial to set the

desired room temperature. For maximum

cooling turn the TEMP dial to 7 (coolest).

5. Directional Louvers: To direct the airflow,

rotate the small vertical louver wheel next to

the air vent on the front of the air conditioner

NOTE: To minimize wear and tear on the air

conditioner, always wait at least 3 minutes before

changing modes. This will help prevent the

compressor from overheating and the circuit

breaker from tripping.

Normal Operating Sounds

• You may hear a pinging noise caused by water hitting

the condenser, on rainy days, or when the humidity is

high. This design feature helps remove moisture and

improve efficiency.

• You may hear the thermostat click when the compres-

sor cycles on and off.

• Water will collect in the base pan during rain or days of

high humidity. The water may overflow and drip from

the outside part of the unit.

• The fan may run even when the compressor is not on.

LOUVER WHEEL

CARE AND CLEANING

Clean your air conditioner to keep it looking new

and to minimize dust build up.

Air Filter Cleaning

The air filter should be checked at least once

every month to see if it needs cleaning. Trapped

particles and dust can build up in the filter and

may decrease airflow as well as cause the

cooling coils to accumulate frost. To clean the air

filter:

1. Remove the filter by sliding it out from the

front right side of the air conditioner. (See

FIG. 13)

2. Wash the filter using liquid dish soap and

warm water. Rinse the filter thoroughly. Gen-

tly shake the filter to remove excess water.

3. Let the filter dry completely before placing it

into the air conditioner.

4. If you do not wish to wash the filter, you may

vacuum the filter to remove the dust and

other particles.

Cabinet Cleaning

To clean the air conditioner cabinet:

• Unplug the air conditioner to prevent shock or

a fire hazard. The cabinet and front panel of

the air conditioner may be dusted with an oil-

free cloth or washed with a cloth dampened in

a solution of warm water and mild liquid soap.

Rinse thoroughly with a damp cloth and wipe

dry.

• Never use harsh cleaners, wax or polish on

the cabinet front.

• Be sure to wring excess water from the cloth

before wiping around the controls. Excess

water in or around the controls may cause

damage to the air conditioner.

Winter Storage

To store the air conditioner when it is not in use

for an extended period of time, remove it care-

fully from the window according to the installation

instructions and cover it with plastic or place it in

the original box.

FIG. 13

PROBLEM

The Air Conditioner will not start

POSSIBLE CAUSES

The air conditioner is unplugged

The fuse is blown/circuit breaker is

tripped.

Power Failure

The current interrupter device is

tripped.

SOLUTIONS

• Make sure the air conditioner is

plug is pushed completely into the

outlet

• Check the house fuse/circuit

breaker box and replace the fuse

or reset the breaker.

• The unit will automatically re-start

when power is restored.

• There is a protective time delay

(approx. 3 minutes) to prevent

tripping of the compressor

overload. For this reason, the unit

may not start normal cooling for 3

minutes after it is turned back on.

• Press the RESET button located

on the power cord plug.

• If the RESET button will not stay

engaged, discontinue use of the

air conditioner and contact a

qualified service technician.

TROUBLESHOOTING

The Air Conditioner does not cool

as it should

Airflow is restricted

The temperature control may not be

set correctly.

The air filter is dirty

The room may be too warm

Cold air is escaping

The Cooling Coils are frozen

• Make sure there are no curtains,

blinds, or furniture blocking the

front of the air conditioner

• Turn the TEMP dial to a higher

number

• Clean the filter. See the Cleaning

and Care Section of the manual.

• Please allow time for the room to

cool down after turning on the air

conditioner.

• Check for open furnace registers

and cold air returns

• See “Air Conditioner Freezing Up”

below.

The Air Conditioner is freezing up

Ice blocks the air flow and stops the air

conditioner from cooling the room

• Set the MODE dial to HIGH FAN

or HIGH COOL and set the TEMP

dial to 1 or 2

The Remote Control is not working

(if included with your air condi-

tioner)

The batteries are inserted incorrectly

The batteries may be dead

• Check the position of the batteries.

• Replace the batteries

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air KFR/KFS Series Bedienungsanleitung

Soleus Air

Soleus Air 000/12 - BTU Multi-Room Heat/Cool Room Air... Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air PE2-07R-62 Bedienungsanleitung

Soleus Air

Soleus Air MAC-12K/10K Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-12 Bedienungsanleitung

Soleus Air

Soleus Air 3046364 Bedienungsanleitung

Soleus Air

Soleus Air SG-PTAC-09HPDA Bedienungsanleitung

Soleus Air

Soleus Air KY-32H Bedienungsanleitung

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air KFMHP-18-ID Bedienungsanleitung

Soleus Air

Soleus Air TTW-SLG Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air PSX-08-01 Bedienungsanleitung

Soleus Air

Soleus Air SPTAC-09H Bedienungsanleitung

Soleus Air

Soleus Air KY-32U Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air air-condition Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air WM1-06E-01 Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

Soleus Air

Soleus Air KY-34 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung