Soleus Air TM-PAC-08E3 Bedienungsanleitung

8,000/10,000/12,000 BTU

Portable Air Conditioner

Operating Instructions

Model No.:

TM-PAC-08E3

TM-PAC-10E3

V140306

3119233

Model No.:

TM-PAC-12E4

Thank you for choosing a Soleus Air fueled by TCL Portable Air Conditioner. This owner’s man-

ual will provide you with valuable information necessary for the proper care and maintenance of

your new product. Please take a few moments to thoroughly read the instructions and familiarize

yourself with all the operational aspects of your new Soleus Air fueled by TCL Portable Air Con-

ditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the

store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: _____________________________________________________

Date Purchased: _________________________________________________

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or outlet

grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this

manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced by

the manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

12) Do not mix old and new batteries in the remote control.

Do not mix Alkaline, Standard (Carbon - Zinc) or Rechargeable (Nickel - Cadmium) Batteries.

MODEL NUMBER TM-PAC-08E3 TM-PAC-12E4TM-PAC-10E3

COOLING CAPACITY 8,000 BTU/Hr 12,000 BTU/Hr10,000 BTU/Hr

DEHUMIDIFYING CAPACITY 86 pts per Day 117 pts per Day107 pts per Day

COOLING POWER USAGE 914 Watts, 8.3 Amps 1200 Watts, 10.2 Amps991 Watts, 9.1 Amps

AIR FLOW VOLUME 206 CFM 206 CFM206 CFM

POWER SOURCE 115 V / 60 HZ 115 V / 60 HZ115 V / 60 HZ

SOUND PRESSURE LEVEL 53 dB(A) 54 dB(A)53 dB(A)

PRODUCT WEIGHT 5.Lbs 6 Lbs6Lbs

OPERATING

TEMPERATURE 70℉-95℉70℉-95℉70℉-95℉

PRODUCT DIMENSIONS 10.625” W×18.875” D

×27.375” H

10.625” W×18.875” D

×27.375” H

10.625” W×18.875” D

×27.375” H

REFRIGERANT R-410A R-410AR-410A

Portable Air Conditioner (1)

Exhaust Hose (1)

Exhaust Hose Connector (1)

Window Kit Adapter (1)

Window Kit Adapter Extension (1)

Rubber Plug (2)

Remote Control (1)

AAA Batteries (2)

Caster Lock (2)

Window Kit - Sliding Panels (3)

Drainage Hose (1)

Owner’s Manual (1)

PACKAGE CONTENTS

SPECIFICATIONS

 The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.

 Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cool-

ing mode.

 Power consumption is measured when the fan runs at the highest speed setting.

 These specifications are for reference only. For actual data, please refer to the rating label on the back

of the unit.

 If the environment temperature is higher than the max operating temperature or lower than the minimum operat-

ing temperature, the air conditioner may not work properly.

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet

2. Press TEST Button, circuit should trip, cutting power to the air conditioner

3. Press RESET button for use

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Soleus Home Comfort Customer Service for trou-

bleshooting recommendations.

Note: Your unit’s power cord may differ from the one shown(see Page 5).

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

RESET

TEST

ALTERNATIVE LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to

any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the

air conditioner or attempt to reset the LCDI Plug. Contact Soleus Home Comfort for troubleshooting

recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

LED LIGHT

the LED light will turn off.

Note: Your unit's power cord and plug may differ from the one shown.

WITH LED LIGHT

PRODUCT DIAGRAM

1. Air Outlet Grill

2. Control Panel

3. Casters

4. Air Intake Grill

5. Remote Control Sensor

6. Air Filter

7. Carry Handle

8. Air Exhaust Hose Discharge Opening

9. Condensation Drain Hole

10. Power Cord

11. Product Manual (Not Shown)

12. Exhaust Hose

13. Exhaust Hose Connector

14. Window Kit Adapter

15. Remote Control

16. Caster Locks

17. Rubber Plug

18. Window Kit

19. Window Kit Adapter Extension

20. Drainage Hose

PARTS & ASSEMBLY

PARTS

ASSEMBLY & INSTALLATION

INSTALLATION

When the unit is operating as an air conditioner or dehumidifier, the unit draws in indoor air and exhausts hot air out

of the room to complete the air exchange. When the unit is operating in fan mode no outdoor air exchange takes

place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan.

NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 4.6 ft. long

(approximate length).

MOUNTING THE EXHAUST HOSE

 Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove

packaging and locate components.

 Extend both ends of the exhaust hose approximately 6 inches.

 Screw the window kit adapter onto one end of the exhaust hose counter-clockwise.

 Screw the exhaust hose connector onto the other end of the exhaust hose counter-clockwise.

 Connect the exhaust hose over the Air Exhaust Hose Discharge Opening on the back of the unit.

 Open the window or door and adjust the length of window kit to fit the opening. Then make the kit

fixed.

 Attach the window kit adapter of the exhaust hose to the window kit.

WINDOW KIT INSTALLATION

WINDOW KIT ASSEMBLY GUIDE

2. Assembly:

Slide Panel B and C into Panel A and size to window width. Win-

dows sizes vary. When sizing the window width, be sure that the

window kit assembly is free from gaps and/or air pockets when

taking measurements.

3. Insert the rubber plugs into the holes that correspond with the

width that your window requires to ensure that there are no gaps

or air pockets in the window kit assembly after installation.

1.Parts:

A) Panel

B) Panel with one exhaust hose opening

C) Panel without exhaust hose opening

D) Rubber plug to lock window kit in place

OPERATING INSTRUCTIONS

CONTROL PANEL BUTTONS

1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER

button once more to turn the unit off.

2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Air

Conditioner mode, Dehumidifier mode, Fan only mode, and Auto mode. Each press of the MODE but-

ton will light up a different icon on the control panel. The exhaust hose and window kit must be in-

stalled when the unit is in Air Conditioner, Dehumidifier mode, and Auto mode. When using the unit as

a fan, it is not necessary to keep the exhaust hose and window kit connected to the unit.

3) Temperature - Select the desired temperature by pressing either ▲ or ▼ key when using the unit in

Air Conditioner mode. The temperature indicator flashes to display the desired temperature setting. Af-

ter the temperature is set, the unit will display this temperature setting until it is changed by the user.

The temperature indicator display shows temperature in Fahrenheit. Press and hold the Mode button for

20 seconds to switch between Celsius and Fahrenheit.

4) Bucket Full - When the unit cannot evaporate the collected moisture fast enough, the excess water

will collect in a backup water tank located inside the unit. The control panel will display “Ft” (Full

Tank) if this occurs.

5) Louver Direction - This unit has 4-way directional louvers. Use the louver guides manually to direct

air up and down. To direct air left and right, press the Auto-Swing Button for automatic comfort.

CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS

CONTROL PANEL

Airflow

Auto-Swing

Button

Mode Selection

Button

Decrease

Temperature

Button

Increase

Temperature

Button

POWER

ON/OFF

Button

Fan Mode

Button

Air Conditioner

Mode

Indicator

Dehumidifier

Mode

Indicator

Sleep Mode

Indicator

Fan Speed

Indicator

Fan Mode

Indicator

Auto

Mode

Indicator

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air WS1-05M2-02 Bedienungsanleitung

Soleus Air

Soleus Air WM1-06E-01 Bedienungsanleitung

Soleus Air

Soleus Air HCC-W08ES-A1 Bedienungsanleitung

Soleus Air

Soleus Air FE-08BA Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09H26-A Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-18HCE Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22-ID Technisches Datenblatt

Soleus Air

Soleus Air HCB-P13HP-D Bedienungsanleitung

Soleus Air

Soleus Air WS2-06E-201 Bedienungsanleitung

Soleus Air

Soleus Air GL-PAC-08E4 Bedienungsanleitung

Soleus Air

Soleus Air PH1-14R-03 Bedienungsanleitung

Soleus Air

Soleus Air Soleus LX-100 LX-100 Bedienungsanleitung

Soleus Air

Soleus Air KC-45H Technisches Datenblatt

Soleus Air

Soleus Air SG-PAC-10E2 Bedienungsanleitung

Soleus Air

Soleus Air PE8-11R-32 Bedienungsanleitung

Soleus Air

Soleus Air PSR-06-01 Bedienungsanleitung

Soleus Air

Soleus Air KFIHP-09-ID Bedienungsanleitung

Soleus Air

Soleus Air SG-CAC-08ESE Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-09ESE-26 Bedienungsanleitung

Soleus Air

Soleus Air PE4-11R-03 Bedienungsanleitung

Soleus Air

Soleus Air LX-120 Bedienungsanleitung

Soleus Air

Soleus Air KY-120HP Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE-F Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-15ESE-C Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung