Soleus Air HCC-W08ES-A1 Bedienungsanleitung

Model

HCC-W08ES-A1

HCC-W10ES-A1

Electronic Window Air Conditioner

Operating Instructions

Thank you for choosing a Soleus Air Air Conditioner. This owner’s manual will provide you with

valuable information necessary for the proper care and maintenance of your new product. Please take

a few moments to thoroughly read the instructions and familiarize yourself with all the operational

aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you orothers or evencause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER”or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined

value. The cord will remain de-energized until the devise has been manually reset. This is intended to re-

duce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded

and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground

or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the

air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting

recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

LED LIGHT

the LED light will turn off.

Note: Your units power cord and plug may differ from the one shown.

PACKING LIST

Packing List:

• Window Air Conditioner (1)

• Remote Control (1)

• AAA Batteries (2)

• Top Mounting Rail (1)

• Insert Strip (1)

• Short Screw (8)

• Accordion Panels (2)

• Sash Lock (2)

• Foam Seal (1)

• Long Screw for Window Locking Bracket & Accordion

Panels (12)

• Curtain Lock (2)

• Owner’s Manual (1)

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENTATION OF THE MANUFACTURER. SOLEUS HOME COMFORT HAS NOT CONDUCTED INDEPENDENT

TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN.

Model HCC-W08ES-A1 HCC-W10ES-A1

Power Supply (Ph/V/Hz) 1/115/60 1/115/60

Rated Cooling Capacity (BTU/h) 8,000 10,000

Cooling Power Input (Watts) 708 885

Rated Current Cooling (Amperage) 6.8 7.9

EER/C.O.P 11.3 11.3

Noise Level dB(A) (H/M/L) 61/59/58 59/57/55

Air Flow (H/M/L) CFM 265/247/229 265/247/229

Dehumidifying Capacity 42 Pints per day 55 Pints per day

Product Dimensions (W” x D” x H”) 19 x 19.25x 14.625 19 x 21.5 x 14.375

Package Dimensions (W” x D” x H”) 22.5 x 21.25x 17 22.875 x 24.625x 16.875

Net/Gross Weight (lbs) 57.3/63.9 79.3/83.8

Refrigerant Type R-410A R-410A

Plug Type NEMA 5-15P NEMA 5-15P

INSTALLATION & ASSEMBLY INSTRUCTIONS

Some assembly is required for your new air conditioner. Please read and follow these instructions carefully.

1. This air conditioner is designed to be installed in a

standard double-hung window with a window width

between 23” and 36” (584 mm - 914 mm).

2. The air conditioner can be installed without the

accordion panels to fit in a narrow window opening.

See the window dimensions.

3. The Lower Sash (the lower part of the window that

moves up and down) must allow for 14.5” (368mm) of

vertical clearance when open. (See FIG. 1).

4. All supporting parts must be secured to firm wood,

masonry, or metal.

5. The electrical outlet must be within reach of the power

cord.

NOTE: Save the product packaging and installation instruc-

tions for future reference. Store the air conditioner in the

product box when not in use for an extended period of time.

FIG. 1

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

23" to 3 6"

584mm to 914mm

14.5"

(368mm)

TOP RAIL INSTALLATION

NOTE: Top Rail and the side Panels are offset to provide the proper pitch to the rear of (5/16”). This is necessary for

proper condensation utilization and drainage. If you are not using the side panels, the rear pitch must still be maintained.

1. Attach the top rail onto the top of the outer case using four Short Screws.

unting rail

Top mo

unting railTop mounting rail

Top mo

unting rail

Top mo

unting railTop mounting rail

Top mouting rail

ASSEMBLY & INSTALLATION (CONT.)

Placing the Unit Inside a Normal Window

1. Place the air conditioner on the sill with the bottom

mounting rail against its back edge. Center the air con-

ditioner and close the window securely behind the top

mounting rail. The air conditioner should be slightly

tilted to the outside area. Use a level; about a 1/3 bub-

ble will be the correct case slant to the outside. (See

FIG. 2& FIG. 3)

2. Once the air conditioner is placed, extend both the left

and right accordion panels to the width of the window.

4. Secure the left and right flanges on end bottom side

3. Place the curtain lock between the curtain extensions

and the window sill, drive long screws through the

lock and into the sill as shown below.

Accordion Panel Installation

Now that you have installed the top rail, you can now install

the accordion panels on each side.

1. Place the air conditioner on a hard flat surface.

2. Locate the accordion panels in the box.

3. Insert the side curtains into the upper and lower rails

of the air conditioner. Fasten the curtains to the unit

4. Slide the free end of the accordion panel into the side

panel of the air conditioner.Do this for each side. The

flange for securing the curtain into the window sill will

be facing the room side when installed.

of the panel with long screws.

5. Drive long screws through upper frame holes into

sash seal between the glass and the window to pre-

and lower sashes and secure it with long screws.

Attach the sash lock to the place between the upper

vent air and insects from getting into the room.

7. Cut the foam seal to the window width and insert the

with short screws as shown below.

FIG. 2

FIG. 3

window sash.

8. For added insulation, the insert strip can be inserted

between the air conditioner and window sill. This is

optional.

ach side use 2 long screws.

ASSEMBLY & INSTALLATION (CONT.)

IF AC is Blocked by a Storm Window

A storm window frame will not allow the air conditioner to

tilt properly which in turn will keep it from draining properly.

To adjust for this, attach a board or piece of wood to the

sill. The board or wood piece should have a depth of at

least 1 1/2”. Make sure the board or piece of wood is ap-

proximately 1/2” higher than the storm window frame. This

will allow the air conditioner to tilt enough for proper drain-

age. (See FIG. 4).

Removing the Air Conditioner from the

Window

1. Turn the air conditioner off, and disconnect the power

cord.

2. Remove the sash seal from between windows, and

unscrew sash lock.

3. Remove the screws installed through the frame and

frame lock.

4. Close (slide) the side panels into frame.

5. Keeping a firm grip on air conditioner, raise the sash

and carefully “rock” air conditioner backward to drain

any condensate water in base of unit. Be careful not to

spill any remaining water while lifting unit from window.

6. Store parts with the air conditioner in the box.

SASH

1 1/2” MIN

(38 mm)

STORM

WINDOW

FRAME

Board or wood

piece must be

approximately

1/2” higher

than the storm

window frame

for proper

drainage



USING YOUR AIR CONDITIONER

Electronic Control Panel & Remote Control

1. Power Button: Turns the air conditioner on and

off.

2. Digital Display: Under ON status without timer

setting,the operation mode is Cool, Energy Saver

or Dry mode, and the set temperature will be

displayed.

Under ON status without timer setting, the opera-

tion mode is Fan mode and the room temperature

will be displayed.

Time will be displayedunder timer setting or timer

preview.

3. Temperature Set: Use these buttons on the con-

trol panel and remote to increase or decrease the

Set Temperature (the desired room temperature)

in cooling,energy saver and dry mode.

4. Timer Set: Use these buttons on the control

panel and remote to set the Timer. Each press of

the buttons will increase or decrease the

timer. For timer instructions see #7.

5. Fan Speed: Use the fan speed button to change

the fan speed. Choose between low, medium,

and high.

6. Mode Button: Press the mode button to cycle

through the various modes: Energy Saver, Dry

(Dehumidifier), Fan and Cool.

7. Auto-on Timer: When the air conditioner is off, it

can be set to automatically turn on in 1-24 hours

at the previous set mode and fan setting. To set

the Auto-on Timer, press the TIMER button on the

unit or remote control. The timer can be set in 1

The hour indicator on the bottom right of the dig-

Auto-off Timer: When the air conditioner is on, it

can be set to automatically turn off in 1-24 hours.

To setthe Auto-off Timer, press the TIMER

button on the unit or remote control. The timer

can be set in 1hour increment.

The hour indicator on the bottom right of the dig-

• To see the remaining time, press the TIMER

Button. To change the timer setting use the

▲/▼on the unit or the +/- buttons on the

remote.

• During preview of timer or timer setting,

press Timer button on the panel or remote

8. Filter Reset: After the fan rotates for 250 total

hours, the filter check light will turn on to remind

the user to clean the filter. Press the Filter Reset

button once the filter is cleaned to reset the re-

minder.

NOTE: This display always shows the room temperature in Fan

Mode except when setting the Set temperature or the Timer

Normal Operating Sounds

• You may hear a pinging noise caused by water

hitting the condenser, on rainy days, or when the

humidity is high. This design feature helps re-

move moisture and improve efficiency.

• You may hear the thermostat click when the com-

pressor cycles on and off.

• Water will collect in the base pan during rain or

days of high humidity. The water may overflow

and drip from the outside part of the unit.

• The fan may run even when the compressor is

not on.

hour increment.

controller to cancel the timer setting.

▲/▼

ital display will start flashing.

To switch between Celsius/Fahrenheit display,

press the buttons at the same time.

▲/▼

Point the remote control at the

air conditioner when sending instruction to the

unit.

9. Signal Receiver:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air LX-140BL Bedienungsanleitung

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-10E2 Bedienungsanleitung

Soleus Air

Soleus Air Soleus LX-100 LX-100 Bedienungsanleitung

Soleus Air

Soleus Air LX-135DHP Bedienungsanleitung

Soleus Air

Soleus Air PE3-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air PH1-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air KY-32H Bedienungsanleitung

Soleus Air

Soleus Air KY-320 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-05SM Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air PE4-11R-03 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE-F Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-10ESE-F Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air WS1-05M2-02 Bedienungsanleitung

Soleus Air

Soleus Air MAC-8000 Bedienungsanleitung

Soleus Air

Soleus Air PSJ-05-01A Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-18-ID Technisches Datenblatt

Soleus Air

Soleus Air HCB-P13HP-D Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-10ESE-C Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung