Soleus Air WS1-05M2-02 Bedienungsanleitung

V190108

Air conditioner must be upright for 24 hours prior to operating.

This ensures that the compressor will function as intended.

Model

WS1-05M2-02

5,100 BTU

Window Air Conditioner

Operating Instructions

AIR CONDITIONER

2MF3

File No. SA 12793

Thank you for choosing a Soleus Air Window Air Conditioner. This Owner’s Manual will provide

you with valuable information necessary for the proper care and maintenance of your new product.

Please take a few moments to thoroughly read the instructions and familiarize yourself with all the

operational aspects of your new Soleus Air Window Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the

store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: _____________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

PURCHASE INFORMATION

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a

safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to

all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic

precautions:

 Plug into a grounded 3 prong outlet.

 Do not remove the ground prong.

 Do not use a plug adapter.

 Do not use an extension cord.

 Unplug the air conditioner before servicing.

 Use two or more people to move and install the air

conditioner.

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause death.

All safety messages will directly follow the safety alert symbol and/or the words “DANGER”

or “WARNING.”

All Safety messages alert you of potential hazards, how to reduce the chance of injury, and what

can happen if instructions are not followed correctly.

Failure to immediately follow these in-

structions may cause serious injury or

even death.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the device has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazard if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly.

To test:

1. Plug power cord into wall outlet, the LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs, the LED

light will turn off.

3. Press RESET button to restore power to the unit. Once power is restored, the LED light will turn on.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting recommenda-

tions.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

POWER CORD AND PLUG

RESET

TEST

LED LIGHT

Note: Your unit’s power cord may

differ from the one shown.

PACKAGE CONTENTS

Top Mounting Rail

Air Conditioner

Side Curtain

Top Mounting Rail

Foam Seal

Insert Strip

Short Screw Long Screw Sash Lock Curtain Lock

 Window Air Conditioner (1)

 Top Mounting Rail (1)

 Insert Strip (1)

 Short Screw (8)

 Long Screw for Locking Bracket & Curtains (12)

 Side Curtain (2)

 Sash Lock (2)

 Foam Seal (1)

 Curtain Lock (2)

 Owner’s Manual

Owner’s

Manual

Model Number WS1-05M2-02

Power Supply (Ph/V/Hz) 1/115/60

Rated Cooling Capacity (BTU/h) 5,100

Cooling Power Input (Watts) 455

Rated Current Cooling (Amperage) 4

CEER 11.2

Noise Level dB(A) (L/H) 52/55

Airflow CFM (H/L) 145/120

Dehumidifying Capacity 21.6 Pints per day

Product Dimensions (W” x H” x D”) 16.125” x 11.75” x 15.125”

Package Dimensions (W” x H” x D”) 17.9” x 14.96” x 17.2”

Net/Gross Weight (Lbs.) 40.7/45.1

Refrigerant Type R-410A

Plug Type NEMA 5-15P

SPECIFICATIONS

 Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

 Power consumption is measured when the fan runs at the highest speed setting.

 These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

ELECTRICAL SAFETY

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENATION OF THE MANUFACTURER. SOLEUS N.A. HAS NOT CONDUCTED AN INDEPENDENT TEST TO

VERIFY THE INFORMATION AND SPECIFICATIONS PRESENTED HEREWITHIN.

WARNING:

grounding prong!!

Power supply cord with 3-prong grounding

plug and current detection device

INSTALLATION

Model WS1-05M2-02

Unit Height 11 3/4"

Unit Width 16 1/8"

Min. Window Opening (See FIG 1) 12”

Min. Window Width 20 1/2"

Max Window Width 34"

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If a new

electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made to fit

inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the provided screws. If

not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage (See FIG. 2).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,

or awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

When handling the unit, be careful to avoid cuts from the

sharp metal edges and aluminum fins on the front and rear

coils.

13 1/4" MIN

FIG .2

FIG .1

13 1/4" MIN

Top Rail Installation

NOTE: Top Rail and the Side Panels are offset to provide the proper pitch to the rear of (5/16”). This is necessary for

proper condensation utilization and drainage. If you are not using the side panels, the rear pitch must still be maintained.

1. Attach the top rail onto the top of the outer case using four short screws.

Curtain Installation

1. Insert the side curtains into the upper and lower rails of the air conditioner. Fasten the curtains to the unit with short screws

as shown below.

2. Slide the free end of the curtain into the side panel of the air conditioner. Do this for each side. The flange for securing the

curtain into the window sill will be facing the room side when installed.

3. Once properly sized, remove the backing to expose the adhesive tape.

INSTALLATION

Top mounting rail

INSTALLATION

Placing the Unit Inside a Normal Window

3. Once the air conditioner is placed, extend the left and

right curtains to the width of the window.

4. Place the curtain lock between the curtain extensions and

the window sill, drive long screws through the lock and into

the sill as shown below:

5. Secure the left and right flanges with long screws on the

bottom sides of the curtain.

6. Drive long screws through upper frame holes into win-

dow sash.

7. Attach the sash lock to the place between the upper and

lower sashes and secure it with long screws. Each side uses

2 long screws.

8. Cut the foam seal to the window width and insert the sash

seal between the glass and the window to prevent air and

insects from getting into the room.

9. For added insulation, the insert strip can be installed

between the air conditioner and window sill. This is option-

al.

Foam Seal

Window Sill

Sash Lock

Curtain Locks Flange

Curtain

Remove the Air Conditioner from the Window

(End of Season)

1. Turn the air conditioner off, and disconnect the

power cord.

2. Remove the sash seal from between win-

dows, and unscrew sash lock.

3. Remove the screws installed through the

frame and frame lock.

4. Close (slide) the side panels into frame.

5. Keeping a firm grip on air conditioner, raise the

sash and carefully “rock” air conditioner back-

ward to drain any condensation water in base of

unit. Be careful not to spill any remaining water

while lifting unit from window.

6. Store parts with the air conditioner in the box.

1. Set the unit in the window so that is centered. Place the

unit so that front edge of the bottom rail is against the back

edge of the sill.

2. Bring the window down so that the front edge of the top

rail is in front of the window. Be sure the unit is tilting

slightly to the outside.

Window

Frame

Top Rail

Bottom Rail

1/4”

CONTROL PANEL

COOL MODE

 Turn the MODE selector clockwise to select HIGH COOL, MED COOL or LOW COOL.

 Turn the TEMPERATURE selector clockwise to select the higher cool settings or turn the selector

counter-clockwise to select the lower cool settings.

 Turn the MODE selector to OFF to turn off the unit.

FAN MODE

 Turn the MODE selector counter-clockwise to select HIGH FAN, MED FAN or LOW FAN.

 Turn the MODE selector to OFF to turn off the unit.

Note: TEMPERATURE mode selector does not function on fan mode.

TEMPERATURE SELECTOR

MODE SELECTOR

Andere Handbücher für WS1-05M2-02

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air PH3-09R Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09H26-A Bedienungsanleitung

Soleus Air

Soleus Air MAC 7500 Bedienungsanleitung

Soleus Air

Soleus Air PH5 Series Bedienungsanleitung

Soleus Air

Soleus Air PAC12 Bedienungsanleitung

Soleus Air

Soleus Air KY-32E Bedienungsanleitung

Soleus Air

Soleus Air PSC-12HP-201 Bedienungsanleitung

Soleus Air

Soleus Air LX-140 NT Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air WM1-06E-01 Bedienungsanleitung

Soleus Air

Soleus Air PH1-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air HCB-R135-A-ID Bedienungsanleitung

Soleus Air

Soleus Air PSX-08-01B Bedienungsanleitung

Soleus Air

Soleus Air KY-34 Bedienungsanleitung

Soleus Air

Soleus Air WS1-06E-02 Bedienungsanleitung

Soleus Air

Soleus Air WS1-15E-02 Bedienungsanleitung

Soleus Air

Soleus Air GB-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air KFMHP-18-ID Bedienungsanleitung

Soleus Air

Soleus Air 3119233 Bedienungsanleitung

Soleus Air

Soleus Air GH-PAC-10E5 Bedienungsanleitung

Soleus Air

Soleus Air KY-32H Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-09-OD Technisches Datenblatt

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung