Soleus Air SG-WAC-25HCE Bedienungsanleitung

Model

SG-WAC-25HCE

Electronic Heat & Cool Window A/C

Operating Instructions

Thank you for choosing a Soleus Air powered by Gree Air Conditioner. This owner’s manual will

provide you with valuable information necessary for the proper care and maintenance of your new

product. Please take a few moments to thoroughly read the instructions and familiarize yourself with

all the operational aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

Recommended Ground Method

For your personal safety, this air conditioner must be grounded. This air conditioner is equipped with a 3 prong power

supply cord with a grounded plug. To minimize the possibility of electrical shock, the cord must be plugged into a 3 prong

outlet and grounded in accordance with all local codes and ordinances. If a 3 prong outlet is not available, it is the cus-

tomer’s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrician.

LCDI Power Cord and Plug

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord that is required

by UL. This power supply cord contains state-of-the-art electronics that sense leakage current. If the cord is damaged

and leakage occurs, power will be disconnected from the unit.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test the plug:

1. Plug power cord into a grounded 3 prong outlet

2. Press RESET (on some units a green light will turn on).

3. Press the TEST Button, the circuit should trip and cut all power to the air conditioner (on some units a green light

may turn off.

4. Press the RESET button for use. You will hear a click and the A/C is not ready for use.

NOTES:

• The RESET button must be engaged for proper use.

• The power supply cord must be replaced if it fails to trip when the TEST button is pressed and the unit fails to reset.

• Do not use the power supply cord as an ON/OFF switch. The

power supply cord is designed as a protection device.

• A damaged power supply cord must be replaced with a new

power supply cord from Soleus Air Powered by Gree.

• The power supply cord contains new user serviceable parts.

Opening the tamper-resistant case voids all warranty and per-

formance claims.

NOTE: Your units power cord and plug may differ from the one

shown.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong.

Do not use an adapter

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock

The electrical ratings for your air conditioner are listed on the model and serial

number label located on the front left side of the unit (when facing the front).

Specific electrical requirements are listed in the chart below. Follow the

requirements below for the type of plug on the power supply cord.

Power Supply Cord

It is the customer’s responsibility:

• To contact a qualified electrician

• To assure that the electrical installation is adequate

and in conformance with the National Electrical Code,

ANSI/NFPA 70 - latest edition, and all local codes and

ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

NEMA 6-20P

PARTS LIST

TOOLS NEEDED

Large Flathead Screwdriver

Tape Measurer

Adjustable Wrench or Pliers

Pencil

Level

Socket Wrenches

Phillips Head Screwdriver

Non-Hardware Packing List

• Window Air Conditioner

• AAA Batteries (2)

• Top Mounting Rail

• Foam Top Mounting Rail Seal Strip

• Accordion Panels (2)

• Side Retainer (2)

• Window Sash Seal

• Foam Seal for Bottom Rail

• Owner’s Manual

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model SG-WAC-25HCE

Power Supply (Ph/V/Hz) 1/230~208/60Hz

Rated Cooling Capacity (BTU/h) 25,000/24,700

Cooling Power Input (Watts) 2,660/2,630

Rated Current Cooling (Amperage) 12/13

EER 9.4/9.4

Noise Level dB(A) 60

CFM 510

Dehumidifying Capacity 192 Pints per day

Product Dimensions (W” x H” x D”) 26.5 x 18.625 x 26.5

Package Dimensions (W” x H” x D”) 29.25 x 20.25 x 32

Net/Gross Weight (Lbs) 139/156

Refrigerant Type R-410A

Plug Type NEMA 6-20P

Rated Current Heating (Amperage) 16/15.6

Heating Power Input (Watts) 3,680/3,030

Rated Heating Capacity (BTU/h) 11,000/8,700

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFI-

CATIONS PRESENTED IN THIS USER’S MANUAL

ARE THE PRESENTATION OF THE MANUFAC-

TURER. SOLEUS INTERNATIONAL HAS NOT CON-

DUCTED INDEPENDENT TEST TO THE INFORMA-

TION AND THE SPECIFICATIONS PRESENTED

HEREWITHIN.

INSTALLATION & ASSEMBLY INSTRUCTIONS

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If

a new electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made

to fit inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the needed

screws. If not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage. (See FIG. 2).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees, or

awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

Model SG-WAC-25HCE

Unit Height 18 5/8”

Unit Width 26 1/4”

Min. Window Opening (See

FIG 1) 19 1/2”

Min. Window Width 30”

Max Window Width 41”

FIG. 1

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

FIG. 2

Board or wood piece must

be approximately 1/2” higher

than the storm window frame

for proper drainage

Storm window frame

or obstruction

SASH

Storm window frame or

obstruction

SASH

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

1. Pull down the front panel and remove the filter (FIG. 1 below)

2. Lift the front panel upwards to remove and place to the side.

3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air con-

ditioner (FIG. 2 above)

4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet (FIG. 3 & 4).

5. Remove the two control panel screws from the front panel (FIG 5).

FIG. 2

FIG. 1

FIG. 3 FIG. 4

FIG. 5

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

6. Remove the shipping screws from the top of the unit and both sides of the cabinet if installed (FIG 6 & 7).

7. Hold the cabinet while pulling on the base handle to carefully remove the unit. Do not pull or lift near the top of the

unit (FIG 8).

8. Remove the internal packing material prior to installation (FIG. 9)

FIG. 9

FIG. 6 FIG. 7

FIG. 8

ASSEMBLY & INSTALLATION (CONT.)

Placing the Cabinet Inside the Window

1. Open the window and place the cabinet in the middle

of the window sill.

2. Make sure the bottom rail is seated over the window

sill as shown below. Bring the window down temporar-

ily behind the top angle rail to hold the cabinet in place.

3. Fasten cabinet to window sill using two 3/4” HEX-Head

screws. Pre-drill holes if needed. Add the bottom rail

seal over the screws.

Top Angle Rail and Side Bracket Installation

1. Place the air conditioner on a hard flat surface.

2. Locate the foam gasket and top angle rail

3. Attach the foam gasket to the top angle rail

4. Install top angle side to cabinet as shown in FIG 7

5. Slide the “I” section of the window panel into the side

bracket of the cabinet (FIG. 8a ). Do this for both sides.

6. Insert top and bottom legs of window filler panel frame

into channel in the top angle and bottom rail. Do both

sides. Install side retainer to cabinet as shown. FIG 8B-

FIG. 7

Foam Gasket and Top

Angle Rail

FIG. 9

TOP VIEW

SILL

STOOL

ANGLE

FIG. 8a

FIG. 8b

Install Support Brackets

1. Hold each support bracket flush against the outside of

the window sill. Tighten each bracket to the bottom of

the cabinet as shown below. Mark the brackets at top

lever of the window sill and then remove.

2. Assemble the sill angle brackets to the support brack-

ets at the marked position as shown above. Hand

tighten, but not all the way for any changes that may

need to be made later during installation.

3. Install the support brackets (with sill angle brackets

attached) to the bottom of the cabinet as shown below.

4. Tighten all 6 bolts securely.

Extend the Accordion Panels

1. Carefully raise the window to expose the accordion

panel and panel frame. Loosen the locking screws so

the accordion panels slide easily.

2. Extend each panel to completely fill the width of the

window. Tighten the locking screws when the panels

are fully extended.

Install the Window Lock and Sash Seal

1. Trim the sash seal to fit the width of the window. Insert

the sash seal into space between the upper and lower

sashes.

2. Attach the right angle safety lock as shown below.

Mark

Left

Right

1/2” Long Screws

and Locknuts

Sill Angle

Bracket

Flat Head Bolt

Locknut

1/2” long

screw and

locknuts

2 each req’d

for each sup-

port bracket

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air KFIHP-09-ID Bedienungsanleitung

Soleus Air

Soleus Air SA-50 Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air WS1-06E-02 Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-10E2 Bedienungsanleitung

Soleus Air

Soleus Air KY-32U Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE Bedienungsanleitung

Soleus Air

Soleus Air PE3-09R-03 Bedienungsanleitung

Soleus Air

Soleus Air PSH-09-01 Bedienungsanleitung

Soleus Air

Soleus Air PE2-07R-62 Bedienungsanleitung

Soleus Air

Soleus Air PMC-12HP-201 Bedienungsanleitung

Soleus Air

Soleus Air GB-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air KY-32E Bedienungsanleitung

Soleus Air

Soleus Air MAC-12K/10K Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air KFH-18 Bedienungsanleitung

Soleus Air

Soleus Air PSX-08-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air HM1-10-32 Bedienungsanleitung

Soleus Air

Soleus Air KY-320 Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air PH4-13R-01 Bedienungsanleitung

Soleus Air

Soleus Air WS2-15E-201 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung