Sony WRR-801A Bedienungsanleitung

1997 by Sony Corporation

Operating Instructions

UHF Synthesized

DiversityTuner

3-860-930-31(2)

WRR-801A

[AU]

Table of Contents

Precautions

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

On operation

•The tuner must be used within a temperature range of

0°C to 40°C (32°F to 104°F). Avoid using the tuner

for extended periods at extremely high temperatures

or placing it in direct sunlight, especially outdoors,

because this may damage the finish of the case.

Never install the tuner on or near a heat source, such

as lighting equipment or power amplifiers.

•To avoid using in very humid or dusty places,

because such use may shorten the life of the tuner.

•To avoid degradation of the signal-to-noise ratio, do

not use the tuner in noisy places or in locations

subject to vibration, such as the following:

– near electrical equipment, such as motors,

transformers or dimmers

– near air conditioning equipment or places subject

to direct air flow from an air conditioner

– near public address loudspeakers

– where adjacent equipment might knock against the

tuner

•Switching lights on or off may produce electrical

interference over the entire frequency range. Position

the tuner and the wireless microphones so that

interference is minimized.

•The tuner is precisely adjusted at the factory and no

adjustment before use is necessary. Do not touch the

inside of the tuner or try to repair it by yourself.

On cleaning

Clean the tuner with a dry, soft cloth. Never use

thinner, benzene, alcohol or any other chemicals, since

these may damage the finish.

(AU)

Table of Contents

Precautions....................................................... 2

Overview ........................................................... 4

Features ............................................................. 4

System Configuration........................................ 4

Wirelss Channels Selectable .......................... 5

Wireless Channel Lists ...................................... 5

Location of Parts and Controls....................... 8

Front Panel ........................................................ 8

Dispaly .............................................................. 8

Rear Panel ......................................................... 9

Installing a WRU-801ATuner Unit ................. 10

Connections ................................................... 11

Basic Connections ........................................... 11

Connection for Multichannel Operation ......... 11

Channel Setting.............................................. 12

Automatic Search and Setting of Available

Channels..................................................... 13

Operation ........................................................ 14

Muting Functions ............................................ 14

Rack Mounting ............................................... 15

Error Messages .............................................. 15

Specifications................................................. 16

Overview

Space diversity reception system

The WRR-801A provides stable signal reception with

minimum dropout.

Tone squelch circuit for noise elimination

A built-in squelch circuit eliminates noise and signal

interference when the WRR-801A is in signal

reception standby mode.

Compander system

A compander (compressor/expander) system enables

stabilized wireless transmission over a wide dynamic

range.

Rack mounting

The WRR-801A can be mounted in an EIA standard

19-inch rack (1U size).

System Configuration

The tuner can be used with a Sony UHF synthesized

wireless microphone or UHF synthesized transmitter

among the models listed in the table below.

Sony 800 MHz-band system models

Overview

The WRR-801A is a reliable UHF synthesized

diversity tuner for the 800-MHz-band Sony UHF

wireless microphone system which uses the frequency

bands allocated for UHF TV broadcasting.

This tuner is designed to enable simultaneous use of

multiple channels when channels are selected

according to the Sony channel plan.

Installing six WRU-801A UHF Synthesized Tuner

Units will enable six-channel operation on the tuner.

At shipping, one tuner unit is installed in the tuner, and

additional tuner units (sold separately) can be installed

easilly.

Features

Phase Locked Loop (PLL) synthesized

system

The WRR-801A has a refined phase locked loop

(PLL) synthesizer circuit and covers two UHF TV

channels. It operates on 102 channels over a 14-MHz

frequency.

Preprogrammed wireless channel plan for

simultaneous multichannel operation

The WRR-801A has many preprogrammed, easily

settable channels for simultaneous multichannel

operation. One group allows setting of 102 channels.

The tuner also has 12 preset groups of channels, each

of which permits simultaneous operation of 5, 6, 8, 9

or 12 channels without the effects of intermodulation.

Modular multichannel reception

By installing optional WRU-801A UHF Synthesized

Tuner Units, you can receive up to six channels on one

WRR-801A unit.

Versatile display

A liquid-crystal display provides a variety of

information, including the levels of the reception

channels, RF information and transmitter battery

condition.

792.250 to

798.500

Model name

WRR-800A (66)

WRR-801A (66)

WRR-810A (66)

WRR-820A (66)

WRR-840A (66)

WRR-850A (66)

WRR-860A (66)

Tuner

WRT-800A (66)

WRT-805A (66)

WRT-810A (66)

WRT-820A (66)

WRT-830A (66)

WRT-860A (66)

WRT-867A (66)

Frequency band

Frequency

(MHz)

TV channel Transmitter or

microphone

799.250 to

805.500

Wirelss Channels Selectable

The tuner stores thirteen groups of selectable channels:

groups 00 (102 channels), 11 (12 channels),

12 (9 channels), 13 (9 channels), A1 (8 channels), A2

(6 channels), A3 (6 channels), L1 (6 channels), L2 (6

channels), M1 (6 channels), M2 (5 channels), H1 (8

channels) and H2 (8 channels).

Channel groups other than group 00 are designed so

that all channels of one group can be used

simultaneously within the same UHF wireless

microphone system without causing intermodulation.

It is therefore recommended that you usually use a

channel group other than group 00 unless the use of

group 00 is specifically necessary.

Each “wireless channel” is represented by a 2-digit TV

channel number and a 2-digit number, for example:

66-23.

Note

To eliminate interference or noise, please note the

following.

•Do not use two or more wireless microphones or

transmitters whose wireless channels are the same.

•If there is a TV broadcasting station nearby, to avoid

possible interference from its broadcasting, do not

use that station’s channel.

•The number of wireless microphone channels

actually usable in a multi-channel system may be

smaller than the normal capacity of that system if

there is interference from TV broadcasting or other

RF signals.

•When operating two or more UHF wireless

microphone systems using the same wireless channel

in the same group, ensure that the systems are at least

100 m (330 feet)1) apart as far as they are installed

within sight of each other.

1) The distance depends on the operating environment and

conditions.

Wireless Channel Lists

Group 00: All channel access

Use only for a one-channel system or to scan for open

channels.

..........................................................................................................................................................................................................

66-01 792.250

66-02 792.375

66-03 792.500

66-04 792.625

66-05 792.750

66-06 792.875

66-07 793.000

66-08 793.125

66-09 793.250

66-10 793.375

66-11 793.500

66-12 793.625

66-13 793.750

66-14 793.875

66-15 794.000

66-16 794.125

66-17 794.250

66-18 794.375

66-19 794.500

66-20 794.625

66-21 794.750

66-22 794.875

66-23 795.000

66-24 795.125

66-25 795.250

66-26 795.375

66-27 795.500

66-28 795.625

66-29 795.750

66-30 795.875

66-31 796.000

66-32 796.125

66-33 796.250

66-34 796.375

66-35 796.500

66-36 796.625

66-37 796.750

66-38 796.875

66-39 797.000

66-40 797.125

66-41 797.250

66-42 797.375

66-43 797.500

66-44 797.625

66-45 797.750

66-46 797.875

66-47 798.000

66-48 798.125

66-49 798.250

66-50 798.375

66-51 798.500

WL Channel Frequency (MHz) WL Channel Frequency (MHz)

67-01 799.250

67-02 799.375

67-03 799.500

67-04 799.625

67-05 799.750

67-06 799.875

67-07 800.000

67-08 800.125

67-09 800.250

67-10 800.375

67-11 800.500

67-12 800.625

67-13 800.750

67-14 800.875

67-15 801.000

67-16 801.125

67-17 801.250

67-18 801.375

67-19 801.500

67-20 801.625

67-21 801.750

67-22 801.875

67-23 802.000

67-24 802.125

67-25 802.250

67-26 802.375

67-27 802.500

67-28 802.625

67-29 802.750

67-30 802.875

67-31 803.000

67-32 803.125

67-33 803.250

67-34 803.375

67-35 803.500

67-36 803.625

67-37 803.750

67-38 803.875

67-39 804.000

67-40 804.125

67-41 804.250

67-42 804.375

67-43 804.500

67-44 804.625

67-45 804.750

67-46 804.875

67-47 805.000

67-48 805.125

67-49 805.250

67-50 805.375

67-51 805.500

Wirelss Channels Selectable

Group 11: 12-channel group

Use when TV channels both 66 and 67 are available.

Group 12: 9-channel group

Use when TV channel 66 is on the air.

Group 13: 9-channel group

Use when TV channel 67 is on the air.

WL Channel Frequency (MHz)

66-02 792.375

66-07 793.000

66-17 794.250

66-19 794.500

66-35 796.500

66-43 797.500

67-08 800.125

67-19 801.500

67-33 803.250

67-39 804.000

67-42 804.375

67-46 804.875

Group A1: 8-channel group

Use when both TV channels 66 and 67 are available.

Group A2: 6-channel group

Use when TV channel 66 is on the air.

Group A3: 6-channel group

Use when TV channel 67 is on the air.

WL Channel Frequency (MHz)

66-02 792.375

66-04 792.625

66-12 793.625

66-24 795.125

67-02 799.375

67-29 802.750

67-35 803.500

67-44 804.625

WL Channel Frequency (MHz)

67-06 799.875

67-15 801.000

67-21 801.750

67-32 803.125

67-46 804.875

67-50 805.375

WL Channel Frequency (MHz)

67-01 799.250

67-03 799.500

67-11 800.500

67-16 801.125

67-23 802.000

67-27 802.500

67-41 804.250

67-44 804.625

67-50 805.375

WL Channel Frequency (MHz)

66-01 792.250

66-03 792.500

66-11 793.500

66-16 794.125

66-23 795.000

66-27 795.500

66-41 797.250

66-44 797.625

66-50 798.375

WL Channel Frequency (MHz)

66-06 792.875

66-15 794.000

66-21 794.750

66-32 796.125

66-46 797.875

66-50 798.375

Group L1: 6-channel group

Use when TV channel 67 is on the air.

Group M1: 6-channel group

Use when TV channel 67 is on the air.

Group H1: 8-channel group

Use when TV channel 66 is on the air.

Group L2: 6-channel group

Use when TV channel 67 is on the air.

Group M2: 5-channel group

Use when TV channel 67 is on the air.

Group H2: 8-channel group

Use when TV channel 66 is on the air.

WL channel Frequency (MHz)

66-01 792.250

66-03 792.500

66-09 793.250

66-14 793.875

66-18 794.375

66-21 794.750

WL channel Frequency (MHz)

66-31 796.000

66-33 796.250

66-39 797.000

66-44 797.625

66-48 798.125

66-51 798.500

WL channel Frequency (MHz)

67-03 799.500

67-05 799.750

67-11 800.500

67-16 801.125

67-26 802.375

67-35 803.500

67-38 803.875

67-42 804.375

WL channel Frequency (MHz)

66-02 792.375

66-04 792.625

66-10 793.375

66-15 794.000

66-19 794.500

66-22 794.875

WL channel Frequency (MHz)

66-32 796.125

66-34 796.375

66-40 797.125

66-45 797.750

66-49 798.250

WL channel Frequency (MHz)

67-06 799.875

67-08 800.125

67-12 800.625

67-22 801.875

67-25 802.250

67-33 803.250

67-40 804.125

67-45 804.750

Location of Parts and Controls

AF BATT

GP CH

BATT

SET

OFF

POWER

BATT

RF AF BATT

GP CH

12 3 45 6

1POWER switch

2Display

6Blank panels

3GP button

4SET button

5CH button

Front Panel

1POWER switch

Turns the power on and off.

2Display

Displays the status of the tuner and the group and

channel assigned to the unit.

For details, see the following section “Display”.

3GP (group) button

Press to change the group or to display frequencies.

Location of Parts and Controls

1BATT (battery) indicator

5BATT (battery) indication

Indicate the condition of the wireless microphone

transmitter batteries. The indicator and indication start

flashing about one hour before the transmitter batteries

go flat.

1BATT indicator

2RF indicator

3AF indicator

4AF indication

5BATT indication

6GP/CH indication

4SET button

Press to change the group or channel.

5CH (channel) button

Press to change the channel in a group.

6Blank panels

Remove these panels to install optional WRU-801A

UHF Synthesized Tuner Units.

Display

2RF (radio frequency) indicator

7RF (radio frequency) indications

The indicator lights and the indications (dots) appear

when the antenna reception is optimal. Depending on

the RF input level, the number of dots changes.

3AF (audio frequency) indicator

4AF (audio frequency) indication

The indicator lights and the indication appears when

the audio output level is higher than the reference

level.

6GP/CH (group/channel) indication

Shows the reception channel group and respective

channel number.

Pressing the GP button changes this indication to the

frequency indication.

7RF indications

Rear Panel

ANTENNA B TNNER OUTPUT(LINE LEVEL 0dBm) MIX OUTPUT

IN(DC 9V OUT) 564321

ATT

010dB

ANTENNA A AC IN

IN(DC 9V OUT)

ATT

LEVEL

010dB

LINE

0dBm

MIC

–38dBm

⁄

3AC IN connector

4MIX OUTPUT LEVEL switch

5MIX OUTPUT connector

6TUNER OUTPUT connectors

1ANTENNA A, B IN/DC 9V out connectors

2ANTENNA A, B ATT switches

1ANTENNA A, B IN/DC 9V OUT (antenna A, B

input/DC power output) connectors (BNC type)

Connect the supplied antenna or an optional AN-820A

UHF Antenna. To connect two of these units, these

connectors are connected to the ANTENNA OUT

connectors of the WD-820A UHF Antenna Divider.

When the AN-820A is connected, 9 V DC power is

supplied to the antenna’s internal booster through these

connectors.

Note

Never short-circuit these connectors.

2ANTENNA A, B ATT (attenuation) switches

Select the RF attenuation as 0 dB or 10 dB. (Normally,

set the switches to 0 dB.)

3AC IN connector

Connects to an AC power source with the supplied AC

power cord.

4MIX OUTPUT LEVEL switch

Selects the mixed output level as 0 dBm or –38 dBm.

Set this switch according to the input level of the

equipment connected to the tuner.

5MIX OUTPUT connector (ø6.3 phone balanced

(1/4inch TRS))

Supplies mixed audio signals of six tuner units. You

can connect this to the audio input connector of a

mixer, amplifier or similar equipment.

6TUNER OUTPUT (tuner sound output)

connectors (ø6.3 phone balanced (1/4inch TRS))

Each connector supplies the audio signal from the

corresponding tuner unit. You can connect this to the

audio input connector of a mixer, amplifier, or similar

equipment.

Up to five WRU-801A UHF Synthesized Tuner Units

can be installed.

Notes

•Be sure to power this unit off before installing the

WRU-801A.

•The buttons and display on the front panel of the

WRU-801A may be damaged if they are gripped too

strongly. Always hold the WRU-801A by the side.

•Do not touch the connectors on the rear panel of the

WRU-801A.

•Be careful of static electricity.

Installing a WRU-801A

1Power the tuner off and remove the blank panel

with a screwdriver or other tool.

2Hold the WRU-801A by the side and insert into

the slot. Push in until you hear a click.

Installing aWRU-801ATuner Unit

Removing a WRU-801A

On the bottom panel of the tuner, locate the lever

corresponding to the slot where the WRU-801A is

installed and pull the lever forward. The WRU-801A is

ejected from the slot.

Lever

Bottom Panel

Andere Handbücher für WRR-801A

Inhaltsverzeichnis

Andere Sony Tuner Handbücher

Sony

Sony URX-S03D Bedienungsanleitung

Sony

Sony WRU-806B Bedienungsanleitung

Sony

Sony Dream Machine ICF-C743 Bedienungsanleitung

Sony

Sony WRR-800A Bedienungsanleitung

Sony

Sony ST-JX401 Bedienungsanleitung

Sony

Sony FDL-3105 Bedienungsanleitung

Sony

Sony ST-S707ES Bedienungsanleitung

Sony

Sony XDRF1HD - HD Radio Tuner Bedienungsanleitung

Sony

Sony WRR-862A Bedienungsanleitung

Sony

Sony WRU-801A Bedienungsanleitung

Sony

Sony Ipela NSR-S10 Bedienungsanleitung

Sony

Sony ST-S444ES Bedienungsanleitung

Sony

Sony ST-EX880 Bedienungsanleitung

Sony

Sony ST-JX661 Bedienungsanleitung

Sony

Sony URX-M2 Bedienungsanleitung

Sony

Sony ST-SV7 Bedienungsanleitung

Sony

Sony WRU-806B Bedienungsanleitung

Sony

Sony ST-H3600 Bedienungsanleitung

Sony

Sony HCD-WZ5 Bedienungsanleitung

Sony

Sony Ipela NSR-S10 Bedienungsanleitung

Sony

Sony ST-D50L Bedienungsanleitung

Sony

Sony URX-P03D/25 Bedienungsanleitung

Sony

Sony WRU-806B Bedienungsanleitung

Sony

Sony WRR-800A Bedienungsanleitung

Beliebte Tuner Handbücher anderer Marken

Tunersys

Tunersys WS16 1 Bedienungsanleitung

Arcam

Arcam DT91 Bedienungsanleitung

Magnum

Magnum MD 102T Bedienungsanleitung

HDHomeRun

HDHomeRun 20121008 Bedienungsanleitung

Crestron

Crestron C2N-TXM Bedienungsanleitung

Eico

Eico HFT-92 Bedienungsanleitung

MFJ

MFJ MFJ-928 Bedienungsanleitung

NAD

NAD C 445 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SC-FM1 Bedienungsanleitung

Antique Automobile Radio

Antique Automobile Radio 283501B Bedienungsanleitung

Monacor

Monacor PA-1200R Bedienungsanleitung

Technics

Technics ST-X301L Bedienungsanleitung

Manhattan

Manhattan 176156 Bedienungsanleitung

Marantz

Marantz ST-15S1 Bedienungsanleitung

Korg

Korg HA-40 Bedienungsanleitung

Harman Kardon

Harman Kardon TU915 Bedienungsanleitung

Teac

Teac T-1D Bedienungsanleitung

Pioneer

Pioneer GEX-P700DAB Bedienungsanleitung